Manual.ly Logo

Worx WG322E.9 Manual

0.0 · 0 Ratings

PDF manual · 228 Pages

English

M: OA-GPT-54-NAN
page

/ 228

Loading...
6f08fbe1afa9ea4499e535fa65ebe44996da page 16
22
Cordless Chain Saw
EN
• When not in use
• Before moving from one place to another
• Before servicing
• Before changing accessories or attachments, such
as saw chain and guard
2. Inspect chain saw before and after each use.
Check saw closely if guard or other part has been
damaged. Check for any damage that may affect
operator safety or operation of saw. Check for
alignment or binding of moving parts. Check for
broken or damaged parts. Do not use chain saw if
damage affects safety or operation. Have damage
repaired by authorized service center. To locate an
authorized service center, visit www.worx.com
3. Maintain chain saw with care.
• Never expose saw to rain or direct moisture.
• Keep chain sharp, clean, and lubricated for better
and safer performance.
• Follow steps outlined in this manual to sharpen
chain.
• Keep handles dry, clean, and free of oil and grease.
• Keep all screws and nuts tight.
• Keep battery pack from heat, oil, and sharp edges.
4. When servicing, use only identical
replacement parts.
5. When not in use, always store chain saw
• in a high or locked place, out of children’s reach
• in a dry place
• with Bar and Chain Storage/Transportation Cover
(9) in place
Bar Maintenance
To maximize bar life, the following bar maintenance is
recommended.
The bar rails that carry the chain should be cleaned
before storing the tool or if the bar or chain appear to
be dirty.
The rails should be cleaned every time the chain is
removed.
To clean the Bar rails:
1. Remove chain cover and bar and chain. (see
section ASSEMBLY)
2. Using a wire brush, screwdriver or similar tool,
clear the residue from the inner groove of the bar
(See Fig. Q).
3. Make sure to clean oil passages thoroughly
Conditions which require Chain (7) and Guide
Bar (6) maintenance:
• Saw cuts to one side or at an angle.
• Saw has to be forced through the cut.
• Inadequate supply of oil to the bar and chain.
Check the condition of the guide bar each time the
chain is sharpened. A worn guide bar will damage the
chain and make cutting difficult.
After each use, with unit disconnected from power
source, clean all sawdust from the guide bar and
sprocket hole.
When rail top is uneven, use a flat file to restore
square edges and sides.
File Rail Edges
and Sides
Square
Worn Groove Correct Groove
Replace the guide bar when the groove is worn, the
guide bar is bent or cracked, or when excess heating or
burring of the rails occurs. If replacement is necessary,
use only the guide bar specified for your saw in the
repair parts list or on the decal located on the chain
saw.
Replacing Bar & Chain
Replace chain when cutters are too worn to sharpen or
when chain stops. Only use replacement chain noted
in this manual.
Inspect Guide Bar before sharpening chain. A worn or
damaged Guide Bar is unsafe. A worn or damaged Guide
Bar will damage chain. It will also make cutting harder.
Fit the Bar Tensioning Plate (23) Tab into the new bar
by tightening the screw clockwise. The tab protrusion
(a) must be fitted into the bar hole. (See Fig R)
SHARPENING SAW CHAIN
WARNING: Remove the battery pack
before servicing. Severe injury or death
could occur from electrical shock or body
contact with moving chain.
Cutting edges on chain are sharp. Use
protective gloves when handling chain.
Keep chain sharp. Your saw will cut faster and more
safely. A dull chain will cause undue sprocket, guide
bar, chain, and motor wear. If you must force chain
into wood and cutting creates only sawdust with few
large chips, chain is dull.
LUBRICATE SPROCKET
WARNING: Wear heavy duty gloves when
performing any maintenance or service to
this tool. Always remove the battery pack
before performing any service or maintenance
on this tool.
NOTE: It is not necessary to remove the chain or bar
when lubricating the guide bar sprocket.
1. Clean the bar and sprocket
2. Using a grease gun, insert the tip of the gun
into the lubrication hole and inject grease until
it appears at the outside edge of the sprocket tip
(See Fig. S).
3. To rotate the sprocket pull the chain by hand until
the ungreased side of the sprocket is in line with
the grease hole. Repeat the lubrication procedure.
ENVIRONMENTAL
PROTECTION
Waste electrical products must not be disposed
of with household waste. Please recycle where
facilities exist. Check with your local authorities
or retailer for recycling advice.
TROUBLESHOOTING TABLE
The following table gives checks and actions that
you can perform if your machine does not operate

Chat with your Worx WG322E.9 manual using AI

Get instant AI answers from your Worx WG322E.9 manual

Ask anything about the Worx WG322E.9. Answers come from this manual, with the pages they are based on.

WG322E.9 Maintenance Schedule

After every use
Inspect chain saw before and after each use

Check for damage, alignment issues, binding parts, or broken components that may affect safety or operation.

Show in the manual (page 21)
After every use
Clean sawdust from guide bar and sprocket hole

Clean all debris with the unit disconnected from the power source to ensure proper function.

Show in the manual (page 21)
Every time chain is removed
Clean guide bar rails and oil passages

Use a wire brush or screwdriver to clear residue from the inner groove and ensure oil passages are clean.

Show in the manual (page 21)
Every time chain is sharpened
Inspect guide bar condition

Check for wear, bending, or cracking; replace if damaged to prevent chain damage and difficult cutting.

Show in the manual (page 21)
As needed
File guide bar edges square

If rail top is uneven, use a flat file to restore square edges and sides.

Show in the manual (page 21)
Every 10 minutes during operation
Check chain tension while cutting

New chains stretch; check frequently and tighten if loose to avoid kickback and rapid wear.

Show in the manual (page 20)
Before each use
Check oil level and refill if low

Check the Oil Level Window regularly; never operate without oil to prevent extensive damage.

Show in the manual (page 19)
Periodically
Lubricate drive sprocket

Inject grease into the lubrication hole until it appears at the outside edge of the sprocket tip.

Show in the manual (page 22)
M: QW-35-FL

Ask a Question

0/1000

Do you recommend WG322E.9?

Yes No

Frequently Asked Questions

A

It is intended for sawing trees, tree trunks, branches, wooden beams, planks, and similar wood materials. The guidance also warns against cutting mineral materials or non-wood items.

Is this answer helpful?

A

No. The instructions state the chain saw is not filled with oil when supplied. You must fill the bar and chain oil before use and never operate with an empty oil tank, or extensive damage can occur.

Is this answer helpful?

A

Run the saw and point the guide bar tip toward a piece of cardboard or paper on the ground. If an increasing oil pattern appears, the automatic oiler is working properly. If no oil appears with a full reservoir, contact WORX service.

Is this answer helpful?

A

Correct chain tension prevents overheating, reduces the chance of kickback causes, and helps avoid chain jumping out of the guide bar groove. New chains may stretch, so tension should be checked frequently at the start and during operation.

Is this answer helpful?

A

Use a firm two-hand grip, do not overreach or cut above shoulder height, avoid letting the guide bar tip touch anything while running, and only use the manufacturer-specified low-kickback chain and bar. Watch for shifting wood that could pinch the chain.

Is this answer helpful?

A

The manual warns to use extreme caution when cutting limbs under tension because the wood can spring back when tension releases. Plan your cuts to manage spring-back and avoid positions where you could be struck.

Is this answer helpful?

A

Charge the Li-ion battery before the first use, using the charger specified for the WORX 20V PowerShare system. When the battery gets hot after heavy use, allow it to cool before charging. Remove the battery before servicing or adjusting chain tension.

Is this answer helpful?

M: OA-GPT-54-NAN

Advantages and Disadvantages

Advantages

  • Automatic chain lubrication with a 130 ml oil tank helps maintain cutting performance.
  • Low-kickback chain and reduced kickback guide bar are designed to reduce kickback risk.
  • Cordless 20V Max PowerShare platform is convenient for pruning and wood cutting.
  • Includes practical features like chain tensioning with a ratchet mechanism for proper setup.
VS

Disadvantages

  • Must use recommended bar and chain oil and refill before it runs low to avoid damage.
  • Chain tension must be checked frequently; a loose chain can jump and increase kickback risk.
  • 25 cm bar length can limit cutting capacity for larger jobs.
  • Safe results depend on correct technique, PPE, and stable footing.
M: OA-GPT-54-NAN

Product Specification

Type

Chainsaw

Battery

20V, Li-Ion

Bar length

9.84in

Chain speed

12.47ft/s

Chain pitch

3/8"

Chain oil tank

4.40fl oz

Special features

Auxiliary handle, tool-free chain tensioning, automatic chain lubrication, chain brake, bucking spike

Vibration level

8.20ft/s^2

Noise level

96dB(A)

Weight

5.29lb

Scope of delivery

without charger and battery

M: GO-GEM-FL-25

Product Description

Worx WG322E.9 20V PowerShare Cordless Chainsaw Solo

Tackle everyday cutting tasks with the Worx WG322E.9 20V PowerShare cordless chainsaw. Built around the 20V Max platform and designed for mobile work, it is intended for sawing trees, tree trunks, branches, and common wood materials like beams and planks. With a 25 cm bar and a 3/8 chain pitch, it targets clean, controlled cuts for pruning and general landscaping.

Power comes from a WORX 20V PowerShare battery system (the WG322E.9 is presented as a solo model, so battery and charger inclusion can vary by bundle). The chain speed is 3.8 m/s, helping the tool reach full cutting performance quickly, while an automatic oiler keeps lubrication consistent during use. The oil tank holds 130 ml, and you can monitor levels through the oil level window and refill as needed.

For safer handling, the saw is equipped with low-kickback features, including a reduced kickback guide bar and a low-kickback chain. Still, kickback can occur under certain conditions, so the guidance emphasizes firm two-hand control, proper stance, avoiding overreaching, and never letting the guide bar tip touch anything while the chain is moving. The manual also stresses that correct chain tension and lubrication are essential to prevent chain jumping, overheating, and rapid wear.

Key results

  • 25 cm bar and 20V Max cordless design for trimming trees, branches, and wood beams with no cord management.
  • Automatic chain lubrication (130 ml tank) for smoother cutting and longer chain life when oil is correct.
  • Low-kickback chain and reduced kickback guide bar to reduce the risk of sudden reactions during cutting.
  • Tool-focused maintenance and chain tension checks (especially after first use) to avoid overheating and kickback causes.

Pros and cons

Pros

  • Automatic oiler helps keep cutting performance consistent.
  • Low-kickback chain and reduced kickback guide bar improve safety during routine cuts.
  • Adjustable, ratcheting chain tension process supports proper fit.
  • Suitable for a wide range of wood cutting tasks as described in the intended use.

Cons

  • Requires correct bar and chain oil (and never running dry) to prevent damage.
  • Chain tension must be checked regularly; loose chain increases kickback and wear.
  • 25 cm bar limits reach and capacity compared with larger saws.
  • Full safe operation depends on PPE, stance, and technique.

Notes

  • For complete guidance, follow the Worx WG322E.9 20V PowerShare Cordless chainsaw solo Manual, including kickback prevention, lubrication, and storage steps.
M: OA-GPT-54-NAN

© Copyright 2026 Manual.ly