Manual.ly Logo

Worx WG322E.9 Manual

0.0 · 0 Ratings

PDF manual · 228 Pages

English

M: OA-GPT-54-NAN
page

/ 228

Loading...
6f08fbe1afa9ea4499e535fa65ebe44996da page 14
20
Cordless Chain Saw
EN
OPERATION
1. BEFORE USING YOUR CORDLESS TOOL
WARNING! The charger and battery pack are
specially designed to work together so do not
attempt to use any other devices. Never insert
or allow metallic objects into your charger or battery
pack connections because of an electrical failure and
hazard will occur.
NOTE: Your battery pack is UNCHARGED and you
must charge once before use.
The battery charger supplied is matched to the Li-ion
battery installed in the machine. Do not use another
battery charger.
2. CHARGING YOUR BATTERY PACK
The Li-ion battery is protected against deep
discharging. When the battery is empty, the machine is
switched off by means of a protective circuit.
In a warm environment or after heavy use, the battery
pack may become too hot to permit charging. Allow
time for the battery to cool down before recharging.
3. TO REMOVE OR INSTALL BATTERY PACK
(See Fig. I1, I2, I3)
Depress the Battery Pack Release Button to remove the
Battery Pack from your tool. After recharging, insert
the Battery Pack into the battery port. A simple push
and slight pressure will be sufficient until a click is
heard. Check to see if the battery is fully secured.
NOTE: When removing the battery pack, hold it
firmly to avoid dropping and injury.
4. Switching on and off (See Fig. J)
ATTENTION: Check the battery pack
before using your cordless tool. Only use
the battery pack listed in the accessories
section.
For switching on the tool, press the Lock-Out
Button (15), then fully press the On/Off Switch (2) and
hold in this position. The Lock-Out Button can now be
released.
For switching off, release the On/Off Switch.
5. CUTTING
IMPORTANT: Is the oil tank filled? Check
the Oil Level Window (14) prior to
starting and regularly during operation
(See Fig. K1). Refill oil when oil level is low. A
full oil tank will last approx. 12 minutes of
cutting depending on sawing intensity and
stops.
Check recent replaced chain tension about
every 10 minutes during operation.
1) Installing the battery pack into the machine.
2) Make sure section of log to be cut is not laying
on the ground. This will keep the chain (7) from
touching the ground as it cuts through the log.
Touching the ground while the Chain is moving is
dangerous and will dull the Chain.
3) Use both hands to grip saw. Always use left hand
to grip Front Handle(4) and right hand to grip Rear
Handle (1). Use a firm grip. Thumbs and fingers
must wrap around saw handles. (See Fig. K2)
4) Make sure your footing is firm. Keep feet-shoulder
width apart. Distribute your weight evenly on both
feet.
5) When ready to make a cut, push the Lock-Out
Button (15) completely in with the right thumb
and squeeze the trigger. This will turn saw on.
Releasing the trigger will turn the saw off. Make
sure the saw is running at full speed before
starting a cut.
6) When starting a cut, slowly place moving chain
against the wood. The wood should be as close to
the saw body as possible. Hold saw firmly in place
to avoid possible bouncing or skating (sideways
movement) of saw.
7) Guide the saw using light pressure and do not put
excessive force on the saw, letting the saw do its
work. The motor will overload and can burn out. It
will do the job better and safer at the rate for which
it was intended.
8) Remove the saw from a cut with the saw running at
full speed. Stop the saw by releasing the On/off Switch
(2). Make sure the chain has stopped before setting
the saw down.
9) Keep practicing on scrap logs in a secure working
area until you are comfortable, using a fluid motion
and a steady cutting rate.
Kickback Safety Devices On This Saw
This saw has a low-kickback chain and reduced
kickback Guide Bar. Both items reduce the chance of
kickback. However, kickback can still occur with this
saw.
The following steps will reduce the risk of kickback.
• Use both hands to grip saw while saw is running.
Use firm grip. Thumbs and fingers must wrap
around saw handles.
• Keep all safety items in place on saw. Make sure
they work properly.
• Do not overreach or cut above shoulder height.
• Keep solid footing and balance at all times.
• Stand slightly to the left side of saw. This keeps
your body from being in direct line with chain.
• Do not let Guide Bar nose touch anything when
chain is moving.
• Never try cutting through two logs at same time.
Only cut one log at a time.
• Do not bury the Guide Bar nose or try plunge cut
(boring into wood using Guide Bar nose).
• Watch for shifting of wood or other forces that may
pinch chain.
• Use extreme caution when reentering a previous
cut.
• Use only the low-kickback chain and Guide Bar
(6) that were supplied with this chain saw or
recommended.
• Never use a dull or loose chain. Keep chain sharp
with proper tension.
How to use Saw Safely
1. Use the chain saw only with secure footing.
2. Hold the chain saw at the right-hand side of your

Chat with your Worx WG322E.9 manual using AI

Get instant AI answers from your Worx WG322E.9 manual

Ask anything about the Worx WG322E.9. Answers come from this manual, with the pages they are based on.

WG322E.9 Maintenance Schedule

After every use
Inspect chain saw before and after each use

Check for damage, alignment issues, binding parts, or broken components that may affect safety or operation.

Show in the manual (page 21)
After every use
Clean sawdust from guide bar and sprocket hole

Clean all debris with the unit disconnected from the power source to ensure proper function.

Show in the manual (page 21)
Every time chain is removed
Clean guide bar rails and oil passages

Use a wire brush or screwdriver to clear residue from the inner groove and ensure oil passages are clean.

Show in the manual (page 21)
Every time chain is sharpened
Inspect guide bar condition

Check for wear, bending, or cracking; replace if damaged to prevent chain damage and difficult cutting.

Show in the manual (page 21)
As needed
File guide bar edges square

If rail top is uneven, use a flat file to restore square edges and sides.

Show in the manual (page 21)
Every 10 minutes during operation
Check chain tension while cutting

New chains stretch; check frequently and tighten if loose to avoid kickback and rapid wear.

Show in the manual (page 20)
Before each use
Check oil level and refill if low

Check the Oil Level Window regularly; never operate without oil to prevent extensive damage.

Show in the manual (page 19)
Periodically
Lubricate drive sprocket

Inject grease into the lubrication hole until it appears at the outside edge of the sprocket tip.

Show in the manual (page 22)
M: QW-35-FL

Ask a Question

0/1000

Do you recommend WG322E.9?

Yes No

Frequently Asked Questions

A

It is intended for sawing trees, tree trunks, branches, wooden beams, planks, and similar wood materials. The guidance also warns against cutting mineral materials or non-wood items.

Is this answer helpful?

A

No. The instructions state the chain saw is not filled with oil when supplied. You must fill the bar and chain oil before use and never operate with an empty oil tank, or extensive damage can occur.

Is this answer helpful?

A

Run the saw and point the guide bar tip toward a piece of cardboard or paper on the ground. If an increasing oil pattern appears, the automatic oiler is working properly. If no oil appears with a full reservoir, contact WORX service.

Is this answer helpful?

A

Correct chain tension prevents overheating, reduces the chance of kickback causes, and helps avoid chain jumping out of the guide bar groove. New chains may stretch, so tension should be checked frequently at the start and during operation.

Is this answer helpful?

A

Use a firm two-hand grip, do not overreach or cut above shoulder height, avoid letting the guide bar tip touch anything while running, and only use the manufacturer-specified low-kickback chain and bar. Watch for shifting wood that could pinch the chain.

Is this answer helpful?

A

The manual warns to use extreme caution when cutting limbs under tension because the wood can spring back when tension releases. Plan your cuts to manage spring-back and avoid positions where you could be struck.

Is this answer helpful?

A

Charge the Li-ion battery before the first use, using the charger specified for the WORX 20V PowerShare system. When the battery gets hot after heavy use, allow it to cool before charging. Remove the battery before servicing or adjusting chain tension.

Is this answer helpful?

M: OA-GPT-54-NAN

Advantages and Disadvantages

Advantages

  • Automatic chain lubrication with a 130 ml oil tank helps maintain cutting performance.
  • Low-kickback chain and reduced kickback guide bar are designed to reduce kickback risk.
  • Cordless 20V Max PowerShare platform is convenient for pruning and wood cutting.
  • Includes practical features like chain tensioning with a ratchet mechanism for proper setup.
VS

Disadvantages

  • Must use recommended bar and chain oil and refill before it runs low to avoid damage.
  • Chain tension must be checked frequently; a loose chain can jump and increase kickback risk.
  • 25 cm bar length can limit cutting capacity for larger jobs.
  • Safe results depend on correct technique, PPE, and stable footing.
M: OA-GPT-54-NAN

Product Specification

Type

Chainsaw

Battery

20V, Li-Ion

Bar length

9.84in

Chain speed

12.47ft/s

Chain pitch

3/8"

Chain oil tank

4.40fl oz

Special features

Auxiliary handle, tool-free chain tensioning, automatic chain lubrication, chain brake, bucking spike

Vibration level

8.20ft/s^2

Noise level

96dB(A)

Weight

5.29lb

Scope of delivery

without charger and battery

M: GO-GEM-FL-25

Product Description

Worx WG322E.9 20V PowerShare Cordless Chainsaw Solo

Tackle everyday cutting tasks with the Worx WG322E.9 20V PowerShare cordless chainsaw. Built around the 20V Max platform and designed for mobile work, it is intended for sawing trees, tree trunks, branches, and common wood materials like beams and planks. With a 25 cm bar and a 3/8 chain pitch, it targets clean, controlled cuts for pruning and general landscaping.

Power comes from a WORX 20V PowerShare battery system (the WG322E.9 is presented as a solo model, so battery and charger inclusion can vary by bundle). The chain speed is 3.8 m/s, helping the tool reach full cutting performance quickly, while an automatic oiler keeps lubrication consistent during use. The oil tank holds 130 ml, and you can monitor levels through the oil level window and refill as needed.

For safer handling, the saw is equipped with low-kickback features, including a reduced kickback guide bar and a low-kickback chain. Still, kickback can occur under certain conditions, so the guidance emphasizes firm two-hand control, proper stance, avoiding overreaching, and never letting the guide bar tip touch anything while the chain is moving. The manual also stresses that correct chain tension and lubrication are essential to prevent chain jumping, overheating, and rapid wear.

Key results

  • 25 cm bar and 20V Max cordless design for trimming trees, branches, and wood beams with no cord management.
  • Automatic chain lubrication (130 ml tank) for smoother cutting and longer chain life when oil is correct.
  • Low-kickback chain and reduced kickback guide bar to reduce the risk of sudden reactions during cutting.
  • Tool-focused maintenance and chain tension checks (especially after first use) to avoid overheating and kickback causes.

Pros and cons

Pros

  • Automatic oiler helps keep cutting performance consistent.
  • Low-kickback chain and reduced kickback guide bar improve safety during routine cuts.
  • Adjustable, ratcheting chain tension process supports proper fit.
  • Suitable for a wide range of wood cutting tasks as described in the intended use.

Cons

  • Requires correct bar and chain oil (and never running dry) to prevent damage.
  • Chain tension must be checked regularly; loose chain increases kickback and wear.
  • 25 cm bar limits reach and capacity compared with larger saws.
  • Full safe operation depends on PPE, stance, and technique.

Notes

  • For complete guidance, follow the Worx WG322E.9 20V PowerShare Cordless chainsaw solo Manual, including kickback prevention, lubrication, and storage steps.
M: OA-GPT-54-NAN

© Copyright 2026 Manual.ly