Manual.ly Logo

Worx WG322E.9 Manual

0.0 · 0 Ratings

PDF manual · 228 Pages

English

M: OA-GPT-54-NAN
page

/ 228

Loading...
6f08fbe1afa9ea4499e535fa65ebe44996da page a
10
Cordless Chain Saw
EN
GENERAL POWER TOOL
SAFETY WARNINGS
WARNING: Read all safety warnings and
all instructions. Failure to follow the
warnings and instructions may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future
reference.
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-
operated (cordless) power tool.
1. WORK AREA SAFETY
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b)
Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can
cause you to lose control.
2. ELECTRICAL SAFETY
a)
Power tool plugs must match the outlet.
Never modify the plug in any way. Do
not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or
grounded surfaces, such as pipes,
radiators, ranges and refrigerators. There is
an increased risk of electric shock if your body is
earthed or grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d)
Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the
power tool. Keep cord away from heat, oil,
sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use
an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces
the risk of electric shock.
f) If operating a power tool in a damp
location is unavoidable, use a residual
current device (RCD) protected supply. Use
of an RCD reduces the risk of electric shock.
3. PERSONAL SAFETY
a) Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use a power tool while
you are tired or under the influence of
drugs, alcohol or medication. A moment of
inattention while operating power tools may
result in serious personal injury.
b)
Use personal protective equipment. Always
wear eye protection. Protective equipment
such as dust mask, non-skid safety shoes, hard
hat, or hearing protection used for appropriate
conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure
the switch is in the off-position before
connecting to power source and/or battery
pack, picking up or carrying the tool.
Carrying power tools with your finger on the
switch or energising power tools that have the
switch on invites accidents.
d) Remove any adjusting key or wrench
before turning the power tool on. A wrench
or a key left attached to a rotating part of the
power tool may result in personal injury.
e)
Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing
or jewellery. Keep your hair, clothing and
gloves away from moving parts. Loose
clothes, jewellery or long hair can be caught in
moving parts.
g) If devices are provided for the connection
of dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust collection can reduce dust-
related hazards.
4. POWER TOOL USE AND CARE
a) Do not force the power tool. Use the
correct power tool for your application.
The correct power tool will do the job better and
safer at the rate for which it was designed.
b) Do not use the power tool if the switch
does not turn it on and off. Any power tool
that cannot be controlled with the switch is
dangerous and must be repaired.
c) Disconnect the plug from the power
source and/or the battery pack from the
power tool before making any adjustments,
changing accessories, or storing power
tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool’s operation.
If damaged, have the power tool repaired
before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
g) Use the power tool, accessories and
tool bits etc. in accordance with these
instructions, taking into account the

Chat with your Worx WG322E.9 manual using AI

Get instant AI answers from your Worx WG322E.9 manual

Ask anything about the Worx WG322E.9. Answers come from this manual, with the pages they are based on.

WG322E.9 Maintenance Schedule

After every use
Inspect chain saw before and after each use

Check for damage, alignment issues, binding parts, or broken components that may affect safety or operation.

Show in the manual (page 21)
After every use
Clean sawdust from guide bar and sprocket hole

Clean all debris with the unit disconnected from the power source to ensure proper function.

Show in the manual (page 21)
Every time chain is removed
Clean guide bar rails and oil passages

Use a wire brush or screwdriver to clear residue from the inner groove and ensure oil passages are clean.

Show in the manual (page 21)
Every time chain is sharpened
Inspect guide bar condition

Check for wear, bending, or cracking; replace if damaged to prevent chain damage and difficult cutting.

Show in the manual (page 21)
As needed
File guide bar edges square

If rail top is uneven, use a flat file to restore square edges and sides.

Show in the manual (page 21)
Every 10 minutes during operation
Check chain tension while cutting

New chains stretch; check frequently and tighten if loose to avoid kickback and rapid wear.

Show in the manual (page 20)
Before each use
Check oil level and refill if low

Check the Oil Level Window regularly; never operate without oil to prevent extensive damage.

Show in the manual (page 19)
Periodically
Lubricate drive sprocket

Inject grease into the lubrication hole until it appears at the outside edge of the sprocket tip.

Show in the manual (page 22)
M: QW-35-FL

Ask a Question

0/1000

Do you recommend WG322E.9?

Yes No

Frequently Asked Questions

A

It is intended for sawing trees, tree trunks, branches, wooden beams, planks, and similar wood materials. The guidance also warns against cutting mineral materials or non-wood items.

Is this answer helpful?

A

No. The instructions state the chain saw is not filled with oil when supplied. You must fill the bar and chain oil before use and never operate with an empty oil tank, or extensive damage can occur.

Is this answer helpful?

A

Run the saw and point the guide bar tip toward a piece of cardboard or paper on the ground. If an increasing oil pattern appears, the automatic oiler is working properly. If no oil appears with a full reservoir, contact WORX service.

Is this answer helpful?

A

Correct chain tension prevents overheating, reduces the chance of kickback causes, and helps avoid chain jumping out of the guide bar groove. New chains may stretch, so tension should be checked frequently at the start and during operation.

Is this answer helpful?

A

Use a firm two-hand grip, do not overreach or cut above shoulder height, avoid letting the guide bar tip touch anything while running, and only use the manufacturer-specified low-kickback chain and bar. Watch for shifting wood that could pinch the chain.

Is this answer helpful?

A

The manual warns to use extreme caution when cutting limbs under tension because the wood can spring back when tension releases. Plan your cuts to manage spring-back and avoid positions where you could be struck.

Is this answer helpful?

A

Charge the Li-ion battery before the first use, using the charger specified for the WORX 20V PowerShare system. When the battery gets hot after heavy use, allow it to cool before charging. Remove the battery before servicing or adjusting chain tension.

Is this answer helpful?

M: OA-GPT-54-NAN

Advantages and Disadvantages

Advantages

  • Automatic chain lubrication with a 130 ml oil tank helps maintain cutting performance.
  • Low-kickback chain and reduced kickback guide bar are designed to reduce kickback risk.
  • Cordless 20V Max PowerShare platform is convenient for pruning and wood cutting.
  • Includes practical features like chain tensioning with a ratchet mechanism for proper setup.
VS

Disadvantages

  • Must use recommended bar and chain oil and refill before it runs low to avoid damage.
  • Chain tension must be checked frequently; a loose chain can jump and increase kickback risk.
  • 25 cm bar length can limit cutting capacity for larger jobs.
  • Safe results depend on correct technique, PPE, and stable footing.
M: OA-GPT-54-NAN

Product Specification

Type

Chainsaw

Battery

20V, Li-Ion

Bar length

9.84in

Chain speed

12.47ft/s

Chain pitch

3/8"

Chain oil tank

4.40fl oz

Special features

Auxiliary handle, tool-free chain tensioning, automatic chain lubrication, chain brake, bucking spike

Vibration level

8.20ft/s^2

Noise level

96dB(A)

Weight

5.29lb

Scope of delivery

without charger and battery

M: GO-GEM-FL-25

Product Description

Worx WG322E.9 20V PowerShare Cordless Chainsaw Solo

Tackle everyday cutting tasks with the Worx WG322E.9 20V PowerShare cordless chainsaw. Built around the 20V Max platform and designed for mobile work, it is intended for sawing trees, tree trunks, branches, and common wood materials like beams and planks. With a 25 cm bar and a 3/8 chain pitch, it targets clean, controlled cuts for pruning and general landscaping.

Power comes from a WORX 20V PowerShare battery system (the WG322E.9 is presented as a solo model, so battery and charger inclusion can vary by bundle). The chain speed is 3.8 m/s, helping the tool reach full cutting performance quickly, while an automatic oiler keeps lubrication consistent during use. The oil tank holds 130 ml, and you can monitor levels through the oil level window and refill as needed.

For safer handling, the saw is equipped with low-kickback features, including a reduced kickback guide bar and a low-kickback chain. Still, kickback can occur under certain conditions, so the guidance emphasizes firm two-hand control, proper stance, avoiding overreaching, and never letting the guide bar tip touch anything while the chain is moving. The manual also stresses that correct chain tension and lubrication are essential to prevent chain jumping, overheating, and rapid wear.

Key results

  • 25 cm bar and 20V Max cordless design for trimming trees, branches, and wood beams with no cord management.
  • Automatic chain lubrication (130 ml tank) for smoother cutting and longer chain life when oil is correct.
  • Low-kickback chain and reduced kickback guide bar to reduce the risk of sudden reactions during cutting.
  • Tool-focused maintenance and chain tension checks (especially after first use) to avoid overheating and kickback causes.

Pros and cons

Pros

  • Automatic oiler helps keep cutting performance consistent.
  • Low-kickback chain and reduced kickback guide bar improve safety during routine cuts.
  • Adjustable, ratcheting chain tension process supports proper fit.
  • Suitable for a wide range of wood cutting tasks as described in the intended use.

Cons

  • Requires correct bar and chain oil (and never running dry) to prevent damage.
  • Chain tension must be checked regularly; loose chain increases kickback and wear.
  • 25 cm bar limits reach and capacity compared with larger saws.
  • Full safe operation depends on PPE, stance, and technique.

Notes

  • For complete guidance, follow the Worx WG322E.9 20V PowerShare Cordless chainsaw solo Manual, including kickback prevention, lubrication, and storage steps.
M: OA-GPT-54-NAN

© Copyright 2026 Manual.ly