Manual.ly Logo

Worx WG322E.9 Manual

0.0 · 0 Ratings

PDF manual · 228 Pages

English

M: OA-GPT-54-NAN
page

/ 228

Loading...
6f08fbe1afa9ea4499e535fa65ebe44996da page 15
21
Cordless Chain Saw
EN
body (See Fig. L).
3. The Chain (7) must be running at full speed before
it makes contact with the wood.
4. Use the Bumper Spikes (13) to secure the saw onto
the wood before starting to cut.
5. Use the Bumper Spikes as a leverage point while
cutting. (See Fig. M)
6. Do not operate the chain saw with arms fully
extended, attempt to saw areas which are difficult
to reach, or stand on a ladder while sawing (see
Fig. N).
Never use the chain saw above shoulder height
CUTTING WOOD UNDER TENSION (See fig. O)
WARNING: When cutting a limb that is
under tension, use extreme caution. Be
alert for wood springing back. When
wood tension is released, limb could spring
back and strike operator causing severe injury
or death.
When sawing logs supported on both ends, start
the cut from above(Y) about 1/3 of the diameter into
the log (overbuck) and then finish the cut (Z) from
below, in order to avoid contact of the chain saw with
the ground. When sawing logs supported on only
one end, start the cut from below (Y) about 1/3 of
the diameter into the log (underbuck) and finish the
cut from above (Z) in order to avoid log splitting or
jamming of the chain saw.
OPERATION FOR POLE SAW (ONLY FOR
WG323E, WG323E.9)
Cutting with shoulder strap (See Fig. P1)
The extension pole is supplied with a shoulder strap
that gives extra support when hoisting the Pole Saw in
the air. Hook the shoulder strap to the extension pole
and wrap around your shoulder. The shoulder strap
can also soften the impact if the Pole Saw is dropped
after the completion of a cut.
Cutting with extension pole
1. Install the battery pack into the machine.
2. Before cutting a high branch, consider all the same
points detailed in the previous section “Trimming
Branches” but pay particular attention to the likely
path of the falling branch.
WARNING: Do not stand directly below
a branch being cut. Keep bystanders far
away. Do not stand on a ladder or other type
of unstable support while using the tool. Do
not use the tool near cable, electrical power or
telephone lines. Keep 3m(10 ft) away from all
power lines. (See Fig. P2-P5)
3. Use both hands to grip Pole Saw. Use only
designated grip areas when operating Pole Saw
(See Fig. P6). Use firm grip. Thumbs and fingers
must wrap around Pole Saw handle and pole.
4. Make sure your footing is firm. Keep feet apart.
Divide your weight evenly on both feet.
5. When ready to make a cut, press the Lock-out
Button (30), then fully press the On/off Switch (31)
(See Fig. P7). This will turn Pole Saw on. Releasing
On/off Switch will turn Pole Saw off. Make sure
saw is running at full speed before starting a cut.
6. When starting a cut, place moving chain
against wood. Hold Pole Saw firmly in place to
avoid possible bouncing or skating (sideways
movement) of saw.
7. Guide Pole Saw using light pressure. Do not force
Pole Saw. The motor will overload and can burn
out. It will do the job better and safer at the rate for
which it was intended.
8. Remove Pole Saw from a cut with saw running
at full speed. Stop Pole Saw by releasing trigger.
Make sure chain has stopped before setting Pole
Saw down.
TRIMMING A TREE (PRUNING)
WARNING: Avoid kickback. Kickback can
result in severe injury or death.
See Kickback, to avoid risk of kickback.
WARNING: Do not operate Pole Saw while
• in a tree
• on a ladder or any other unstable surface
• in any awkward position
You may lose control of Pole Saw causing
severe injury.
WARNING: Do not extend arms above
shoulders when using Pole Saw.
CAUTION: Seek professional help if facing
conditions beyond your ability.
Trimming a tree is the process of cutting limbs from a
living tree. Make sure your footing is firm. Keep feet
apart. Divide your weight evenly on both feet.
Follow directions below to trim a tree.
1. Make first cut 15cm from tree trunk on underside
of limb. Use top of guide bar to make this cut. Cut
1/3 through diameter of limb (See Fig. P8).
2. Move 5 to 10cm farther out on limb. Make second
cut from above limb. Continue cut until you cut
limb off.
3. Make third cut as close to tree trunk as possible
on underside of limb stub. Use top of guide bar to
make this cut. Cut 1/3 through diameter of stub.
4. Make fourth cut directly above third cut. Cut down
to meet third cut. This will remove limb stub.
SAW MAINTENANCE
Follow maintenance instructions in this manual.
Proper cleaning of saw and chain and Guide Bar
maintenance can reduce chances of kickback. Inspect
and maintain saw after each use. This will increase the
service life of your saw.
NOTE: Even with proper sharpening, risk of kickback
can increase with each sharpening.
MAINTENANCE AND
STORAGE OF CHAIN SAW
1. Remove the battery pack

Chat with your Worx WG322E.9 manual using AI

Get instant AI answers from your Worx WG322E.9 manual

Ask anything about the Worx WG322E.9. Answers come from this manual, with the pages they are based on.

WG322E.9 Maintenance Schedule

After every use
Inspect chain saw before and after each use

Check for damage, alignment issues, binding parts, or broken components that may affect safety or operation.

Show in the manual (page 21)
After every use
Clean sawdust from guide bar and sprocket hole

Clean all debris with the unit disconnected from the power source to ensure proper function.

Show in the manual (page 21)
Every time chain is removed
Clean guide bar rails and oil passages

Use a wire brush or screwdriver to clear residue from the inner groove and ensure oil passages are clean.

Show in the manual (page 21)
Every time chain is sharpened
Inspect guide bar condition

Check for wear, bending, or cracking; replace if damaged to prevent chain damage and difficult cutting.

Show in the manual (page 21)
As needed
File guide bar edges square

If rail top is uneven, use a flat file to restore square edges and sides.

Show in the manual (page 21)
Every 10 minutes during operation
Check chain tension while cutting

New chains stretch; check frequently and tighten if loose to avoid kickback and rapid wear.

Show in the manual (page 20)
Before each use
Check oil level and refill if low

Check the Oil Level Window regularly; never operate without oil to prevent extensive damage.

Show in the manual (page 19)
Periodically
Lubricate drive sprocket

Inject grease into the lubrication hole until it appears at the outside edge of the sprocket tip.

Show in the manual (page 22)
M: QW-35-FL

Ask a Question

0/1000

Do you recommend WG322E.9?

Yes No

Frequently Asked Questions

A

It is intended for sawing trees, tree trunks, branches, wooden beams, planks, and similar wood materials. The guidance also warns against cutting mineral materials or non-wood items.

Is this answer helpful?

A

No. The instructions state the chain saw is not filled with oil when supplied. You must fill the bar and chain oil before use and never operate with an empty oil tank, or extensive damage can occur.

Is this answer helpful?

A

Run the saw and point the guide bar tip toward a piece of cardboard or paper on the ground. If an increasing oil pattern appears, the automatic oiler is working properly. If no oil appears with a full reservoir, contact WORX service.

Is this answer helpful?

A

Correct chain tension prevents overheating, reduces the chance of kickback causes, and helps avoid chain jumping out of the guide bar groove. New chains may stretch, so tension should be checked frequently at the start and during operation.

Is this answer helpful?

A

Use a firm two-hand grip, do not overreach or cut above shoulder height, avoid letting the guide bar tip touch anything while running, and only use the manufacturer-specified low-kickback chain and bar. Watch for shifting wood that could pinch the chain.

Is this answer helpful?

A

The manual warns to use extreme caution when cutting limbs under tension because the wood can spring back when tension releases. Plan your cuts to manage spring-back and avoid positions where you could be struck.

Is this answer helpful?

A

Charge the Li-ion battery before the first use, using the charger specified for the WORX 20V PowerShare system. When the battery gets hot after heavy use, allow it to cool before charging. Remove the battery before servicing or adjusting chain tension.

Is this answer helpful?

M: OA-GPT-54-NAN

Advantages and Disadvantages

Advantages

  • Automatic chain lubrication with a 130 ml oil tank helps maintain cutting performance.
  • Low-kickback chain and reduced kickback guide bar are designed to reduce kickback risk.
  • Cordless 20V Max PowerShare platform is convenient for pruning and wood cutting.
  • Includes practical features like chain tensioning with a ratchet mechanism for proper setup.
VS

Disadvantages

  • Must use recommended bar and chain oil and refill before it runs low to avoid damage.
  • Chain tension must be checked frequently; a loose chain can jump and increase kickback risk.
  • 25 cm bar length can limit cutting capacity for larger jobs.
  • Safe results depend on correct technique, PPE, and stable footing.
M: OA-GPT-54-NAN

Product Specification

Type

Chainsaw

Battery

20V, Li-Ion

Bar length

9.84in

Chain speed

12.47ft/s

Chain pitch

3/8"

Chain oil tank

4.40fl oz

Special features

Auxiliary handle, tool-free chain tensioning, automatic chain lubrication, chain brake, bucking spike

Vibration level

8.20ft/s^2

Noise level

96dB(A)

Weight

5.29lb

Scope of delivery

without charger and battery

M: GO-GEM-FL-25

Product Description

Worx WG322E.9 20V PowerShare Cordless Chainsaw Solo

Tackle everyday cutting tasks with the Worx WG322E.9 20V PowerShare cordless chainsaw. Built around the 20V Max platform and designed for mobile work, it is intended for sawing trees, tree trunks, branches, and common wood materials like beams and planks. With a 25 cm bar and a 3/8 chain pitch, it targets clean, controlled cuts for pruning and general landscaping.

Power comes from a WORX 20V PowerShare battery system (the WG322E.9 is presented as a solo model, so battery and charger inclusion can vary by bundle). The chain speed is 3.8 m/s, helping the tool reach full cutting performance quickly, while an automatic oiler keeps lubrication consistent during use. The oil tank holds 130 ml, and you can monitor levels through the oil level window and refill as needed.

For safer handling, the saw is equipped with low-kickback features, including a reduced kickback guide bar and a low-kickback chain. Still, kickback can occur under certain conditions, so the guidance emphasizes firm two-hand control, proper stance, avoiding overreaching, and never letting the guide bar tip touch anything while the chain is moving. The manual also stresses that correct chain tension and lubrication are essential to prevent chain jumping, overheating, and rapid wear.

Key results

  • 25 cm bar and 20V Max cordless design for trimming trees, branches, and wood beams with no cord management.
  • Automatic chain lubrication (130 ml tank) for smoother cutting and longer chain life when oil is correct.
  • Low-kickback chain and reduced kickback guide bar to reduce the risk of sudden reactions during cutting.
  • Tool-focused maintenance and chain tension checks (especially after first use) to avoid overheating and kickback causes.

Pros and cons

Pros

  • Automatic oiler helps keep cutting performance consistent.
  • Low-kickback chain and reduced kickback guide bar improve safety during routine cuts.
  • Adjustable, ratcheting chain tension process supports proper fit.
  • Suitable for a wide range of wood cutting tasks as described in the intended use.

Cons

  • Requires correct bar and chain oil (and never running dry) to prevent damage.
  • Chain tension must be checked regularly; loose chain increases kickback and wear.
  • 25 cm bar limits reach and capacity compared with larger saws.
  • Full safe operation depends on PPE, stance, and technique.

Notes

  • For complete guidance, follow the Worx WG322E.9 20V PowerShare Cordless chainsaw solo Manual, including kickback prevention, lubrication, and storage steps.
M: OA-GPT-54-NAN

© Copyright 2026 Manual.ly