Manual.ly Logo

Worx WG384E Manual

0.0 · 0 Ratings

PDF manual · 88 Pages

English

M: QW-35-FL
page

/ 88

Loading...
c7b50bdbc36f698af3a7a103bdd313789403 page 14
20
Cordless Chain Saw
EN
• Follow steps outlined in this manual to sharpen
chain.
• Keep handles dry, clean, and free of oil and grease.
• Keep all screws and nuts tight.
4. When servicing, use only identical replacement
parts.
5. When not in use, always store Chainsaw
• in a high or locked place, out of children’s reach
• in a dry place
• with bar and chain cover in place
Bar Maintenance
To maximize bar life, the following bar maintenance is
recommended.
The bar rails that carry the chain should be cleaned
before storing the tool or if the bar or chain appear to
be dirty.
The rails should be cleaned every time the chain is
removed.
To clean the Bar rails:
1. Remove chain cover and bar and chain. (see
section ASSEMBLY)
2. Using a wire brush, screwdriver or similar tool,
clear the residue from the inner groove of the bar
(See Fig. S).
3. Make sure to clean oil passages thoroughly
Conditions which require chain and guide bar
maintenance:
• Saw cuts to one side or at an angle.
• Saw has to be forced through the cut.
• Inadequate supply of oil to the bar and chain.
Check the condition of the guide bar each time the
chain is sharpened. A worn guide bar will damage the
chain and make cutting difficult.
After each use, remove the battery pack, clean all
sawdust from the guide bar and sprocket hole.
When rail top is uneven, use a flat file to restore
square edges and sides.
File Rail Edges
and Sides
Square
Worn Groove Correct Groove
Replace the guide bar when the groove is worn, the
guide bar is bent or cracked, or when excess heating or
burring of the rails occurs. If replacement is necessary,
use only the guide bar specified for your saw in
the repair parts list or on the decal located on the
Chainsaw.
Replacing Bar & Chain
Replace chain when cutters are too worn to sharpen or
when chain stops. Only use replacement chain noted
in this manual.
Inspect guide bar before sharpening chain. A worn
or damaged guide bar is unsafe. A worn or damaged
guide bar will damage chain. It will also make cutting
harder.
Fit the bar tensioning plate tab into the new bar by
tightening the screw clockwise. The tab protrusion (a)
must be fitted into the bar hole. (See Fig. T)
SHARPENING SAW CHAIN
WARNING: Remove the battery pack
before servicing. Severe injury or death
could occur from electrical shock or body
contact with moving chain.
Cutting edges on chain are sharp. Use
protective gloves when handling chain.
Keep chain sharp. Your saw will cut faster and more
safely. A dull chain will cause undue sprocket, Guide
Bar, chain, and motor wear. If you must force chain
into wood and cutting creates only sawdust with few
large chips, chain is dull.
LUBRICATE SPROCKET
WARNING: Wear heavy duty gloves when
performing any maintenance or service to
this tool. Always remove the battery pack
before performing any service or maintenance
on this tool.
NOTE: It is not necessary to remove the chain or bar
when lubricating the guide bar sprocket.
1. Clean the bar and sprocket
2. Using a grease gun, insert the tip of the gun into
the lubrication hole and inject grease until it
appears at the outside edge of the sprocket tip.
(See Fig. U)
3. To rotate the sprocket pull the chain by hand until
the ungreased side of the sprocket is in line with
the grease hole. Repeat the lubrication procedure.
ENVIRONMENTAL
PROTECTION
Waste electrical products must not be disposed
of with household waste. Please recycle where
facilities exist. Check with your local authorities
or retailer for recycling advice.

Chat with your Worx WG384E manual using AI

Get instant AI answers from your Worx WG384E manual

Ask anything about the Worx WG384E. Answers come from this manual, with the pages they are based on.

WG384E Maintenance Schedule

After each use
Inspect and clean the chainsaw

Remove battery pack. Inspect for damage, alignment, or binding. Clean sawdust from guide bar and sprocket hole.

Show in the manual (page 19)
Every time chain is removed
Clean guide bar rails

Use a wire brush or similar tool to clear residue from inner groove of the bar and clean oil passages thoroughly.

Show in the manual (page 20)
Each time chain is sharpened
Check guide bar condition

Inspect the guide bar for wear, bending, cracking, or excess heating/burring. Replace if damaged.

Show in the manual (page 20)
Regular intervals
Test chain brake function

Perform a function check by activating and deactivating the chain brake via the front hand guard.

Show in the manual (page 18)
Before starting and regularly during operation
Check oil level

Verify oil level window before starting and regularly while operating. Refill when low.

Show in the manual (page 18)
Every 10 minutes during operation
Check new chain tension

If the chain was recently replaced, check its tension every 10 minutes during operation.

Show in the manual (page 18)
As needed (when dull)
Sharpen or replace saw chain

Keep chain sharp. If cutting creates only sawdust or requires forcing, sharpen or replace the chain.

Show in the manual (page 20)
M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend WG384E?

Yes No

Frequently Asked Questions

A

No, the Worx WG384 requires two battery packs to function. The machine will not start unless both battery slots are filled with compatible 20V Max batteries.

Is this answer helpful?

A

If the chain can be lifted more than half the depth of the drive link off the guide bar, it is too loose. New chains stretch quickly so check tension often during the first few uses.

Is this answer helpful?

A

You must use standard bar and chain oil (ISO VG32). Do not use recycled oil or motor oil as this can damage the automatic oiler and void your warranty.

Is this answer helpful?

A

Absolutely not. The manual strictly warns against operating the chainsaw while in a tree. Always stand on solid, level ground to ensure stability and safety.

Is this answer helpful?

A

Runtime varies based on cutting intensity but a full charge typically lasts about 12 minutes of continuous cutting. Using two batteries helps extend total work time.

Is this answer helpful?

A

No, this chainsaw is intended only for cutting wood. Using it on plastic, masonry, or other non-wood materials is dangerous and can cause severe damage to the tool.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Compatible with all WORX 20V Max PowerShare batteries for maximum flexibility
  • Automatic chain lubrication system reduces maintenance and extends chain life
  • Integrated chain brake provides immediate safety protection against kickback
  • Lightweight design at 3.9 kg makes it easy to maneuver and carry
  • Clear oil level window allows for quick and easy monitoring of lubricant
VS

Disadvantages

  • Requires two batteries to operate which may increase initial setup cost
  • Chain tension must be checked frequently as new chains stretch quickly
  • Not suitable for cutting mineral materials or non-wood building components
  • Battery runtime depends on load intensity and may require spare packs for large jobs
  • Oil tank capacity is limited to 150 ml requiring frequent refills on heavy tasks
M: QW-35-FL

Product Specification

Type

Chainsaw

Bar Length

13.78 in

Chain Speed

26.25 ft/s

Chain Pitch

3/8"

Oil Tank Capacity

5.07 fl oz

Features

Battery level indicator, auxiliary handle, brushless motor, tool-free chain tensioning, automatic chain lubrication, chain brake, claw stop

Vibration Level

11.15 ft/s²

Noise Emission

96dB(A)

M: QW-35-FL

Product Description

Worx WG384 40V PowerShare Chainsaw Review

The Worx WG384 40V PowerShare Chainsaw is a versatile cordless tool designed for homeowners and professionals who need reliable wood cutting power without the hassle of cords or gasoline. This battery-powered saw features a robust 40-volt system powered by two 20V Max lithium-ion batteries, ensuring high performance for felling trees, limbing branches, and bucking logs. With a 14-inch guide bar and a chain speed of 8 meters per second, it delivers efficient cuts through various wood types.

One of the standout features of this chainsaw is its compatibility with the Worx PowerShare ecosystem. Users can utilize any 20V Max WORX battery, offering flexibility and convenience for those who already own other tools in the line. The machine includes an automatic oiler to keep the chain lubricated during operation, reducing wear and tear while maintaining safety. Safety is prioritized with a chain brake that activates instantly upon kickback, protecting the operator from sudden recoil.

The ergonomic design ensures comfort during extended use. The front handle and rear grip are positioned for optimal control, allowing users to maintain a firm hold even when cutting difficult timber. The tool also features a clear oil level window, making it easy to monitor fluid levels before and during work. Whether you are clearing storm debris or preparing firewood, the Worx WG384 offers a clean, quiet, and powerful solution.

Important Notes

  • Always wear protective gear including eye protection and hearing guards.
  • Ensure the chain is properly tensioned before each use to prevent accidents.
  • Charge both batteries simultaneously for balanced power output.
  • Never operate the saw above shoulder height or on unstable surfaces like ladders.
M: QW-35-FL

© Copyright 2026 Manual.ly