Manual.ly Logo

Worx WG384E Manual

0.0 · 0 Ratings

PDF manual · 88 Pages

English

M: QW-35-FL
page

/ 88

Loading...
c7b50bdbc36f698af3a7a103bdd313789403 page 12
18
Cordless Chain Saw
EN
4. TO REMOVE OR INSTALL BATTERY PACK
(See Fig. I)
Depress the battery pack release button to remove the
2 battery packs from your tool. After recharging, insert
the 2 battery packs into the battery ports. A simple
push and slight pressure will be sufficient until a click
is heard. Check to see if the battery is fully secured.
Note:
• When removing the battery pack, hold it
firmly to avoid dropping and injury.
• This machine will only run when 2 batteries
are installed. It is recommended to use the
same two batteries and charge the two
batteries at the same time.
• When you use two batteries with different
power, the machine will only run to the
lower common denominator.
5. POWER INDICATOR LIGHT (See Fig. J)
IMPORTANT:
When only one light is illuminated, your battery
is overly discharged, even though the machine
may still be capable to work. Continuing to
operate your machine with the battery in this
discharged condition may reduce the life and
performance of your battery.
When no light are illuminated, at least one
battery is not fully installed or battery may be
defective, please double check the batteries are
fully seated into position.
BATTERY STATUS
• Before starting or after use, press the button
beside the power indicator light on the machine to
check the battery capacity.
• During operation, the battery capacity will be
indicated automatically by the battery power
indicator. The indicator constantly senses and
displays the battery condition as follows.
• For the machine with 2 battery packs with different
power, the power indicator light displays the
battery condition with the lower one of the two
batteries.
Battery indicator
light status
Battery condition
Five green lights
(
) are
illuminated.
The two batteries are in a
highly charged condition.
Two, three or four
green lights are
illuminated.
The two batteries have a
remaining charge. The more
lights are illuminated, the
more battery capacity.
Only one green
light (
)
is illuminated.
The battery level of at least
one battery pack is very low.
Please check and charge the
battery pack.
No light is
illuminated.
At least one battery is not fully
installed or battery may be
defective.
Only one light is
flashing twice per
cycle.
At least one battery is over
discharged (please refer to
the battery charge condition),
please recharge the two
batteries at once before use
again or storage.
Only one light
is flashing three
times per cycle.
At least one battery is hot,
wait for them cool down
before start again.
Only one light is
flashing four times
per cycle.
The machine is over load.
Remove tool from cutting area
and try again.
Only one light is
flashing five times
per cycle.
Chain brake lever is activated.
Pull the front hand guard
towards the operator (position
) to deactivate chain brake.
6. SWITCHING ON AND OFF (SEE FIG. K)
ATTENTION: Check the battery packs before
using your cordless tool. Only use the battery
pack listed in the accessories section.
For switching on the tool, press the lock-out button,
then fully press the on/off switch and hold in this
position. The lock-out button can now be released.
For switching off, release the on/off switch.
NOTE: The chain brake must be activated in order for
the saw to be switched on.
7. CHAIN BRAKE LEVER (See Fig. L)
The chain brake lever is a safety mechanism activated
through the front hand guard, when kickback occurs.
Chain stops immediately.
The following function check should be carried out at
regular intervals. Pull the front hand guard towards
the operator (position
) to deactivate chain brake.
To activate the chain brake, push front hand guard
forwards (position
).
NOTE: If the saw is unable to start, even though it is
assembled properly and working with fully charged
battery packs, then you should check if the chain brake
lever is in the correct position (position
).
8. CUTTING
IMPORTANT: Is the oil tank filled? Check
the Oil Level Window prior to starting and
regularly during operation (See Fig. M). Refill
oil when oil level is low. A full oil tank will last
approx. 12 minutes of cutting depending on
sawing intensity and stops.
Check recent replaced chain tension about
every 10 minutes during operation.
(1) Installing the battery pack into the machine.
(2) Make sure section of log to be cut is not laying on
the ground. This will keep the chain from touching
the ground as it cuts through the log.
Touching the ground while the chain is moving is
dangerous and will dull the chain.
(3) Use both hands to grip saw. Always use left hand
to grip front handle and right hand to grip rear
handle. Use a firm grip. Thumbs and fingers must

Chat with your Worx WG384E manual using AI

Get instant AI answers from your Worx WG384E manual

Ask anything about the Worx WG384E. Answers come from this manual, with the pages they are based on.

WG384E Maintenance Schedule

After each use
Inspect and clean the chainsaw

Remove battery pack. Inspect for damage, alignment, or binding. Clean sawdust from guide bar and sprocket hole.

Show in the manual (page 19)
Every time chain is removed
Clean guide bar rails

Use a wire brush or similar tool to clear residue from inner groove of the bar and clean oil passages thoroughly.

Show in the manual (page 20)
Each time chain is sharpened
Check guide bar condition

Inspect the guide bar for wear, bending, cracking, or excess heating/burring. Replace if damaged.

Show in the manual (page 20)
Regular intervals
Test chain brake function

Perform a function check by activating and deactivating the chain brake via the front hand guard.

Show in the manual (page 18)
Before starting and regularly during operation
Check oil level

Verify oil level window before starting and regularly while operating. Refill when low.

Show in the manual (page 18)
Every 10 minutes during operation
Check new chain tension

If the chain was recently replaced, check its tension every 10 minutes during operation.

Show in the manual (page 18)
As needed (when dull)
Sharpen or replace saw chain

Keep chain sharp. If cutting creates only sawdust or requires forcing, sharpen or replace the chain.

Show in the manual (page 20)
M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend WG384E?

Yes No

Frequently Asked Questions

A

No, the Worx WG384 requires two battery packs to function. The machine will not start unless both battery slots are filled with compatible 20V Max batteries.

Is this answer helpful?

A

If the chain can be lifted more than half the depth of the drive link off the guide bar, it is too loose. New chains stretch quickly so check tension often during the first few uses.

Is this answer helpful?

A

You must use standard bar and chain oil (ISO VG32). Do not use recycled oil or motor oil as this can damage the automatic oiler and void your warranty.

Is this answer helpful?

A

Absolutely not. The manual strictly warns against operating the chainsaw while in a tree. Always stand on solid, level ground to ensure stability and safety.

Is this answer helpful?

A

Runtime varies based on cutting intensity but a full charge typically lasts about 12 minutes of continuous cutting. Using two batteries helps extend total work time.

Is this answer helpful?

A

No, this chainsaw is intended only for cutting wood. Using it on plastic, masonry, or other non-wood materials is dangerous and can cause severe damage to the tool.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Compatible with all WORX 20V Max PowerShare batteries for maximum flexibility
  • Automatic chain lubrication system reduces maintenance and extends chain life
  • Integrated chain brake provides immediate safety protection against kickback
  • Lightweight design at 3.9 kg makes it easy to maneuver and carry
  • Clear oil level window allows for quick and easy monitoring of lubricant
VS

Disadvantages

  • Requires two batteries to operate which may increase initial setup cost
  • Chain tension must be checked frequently as new chains stretch quickly
  • Not suitable for cutting mineral materials or non-wood building components
  • Battery runtime depends on load intensity and may require spare packs for large jobs
  • Oil tank capacity is limited to 150 ml requiring frequent refills on heavy tasks
M: QW-35-FL

Product Specification

Type

Chainsaw

Bar Length

13.78 in

Chain Speed

26.25 ft/s

Chain Pitch

3/8"

Oil Tank Capacity

5.07 fl oz

Features

Battery level indicator, auxiliary handle, brushless motor, tool-free chain tensioning, automatic chain lubrication, chain brake, claw stop

Vibration Level

11.15 ft/s²

Noise Emission

96dB(A)

M: QW-35-FL

Product Description

Worx WG384 40V PowerShare Chainsaw Review

The Worx WG384 40V PowerShare Chainsaw is a versatile cordless tool designed for homeowners and professionals who need reliable wood cutting power without the hassle of cords or gasoline. This battery-powered saw features a robust 40-volt system powered by two 20V Max lithium-ion batteries, ensuring high performance for felling trees, limbing branches, and bucking logs. With a 14-inch guide bar and a chain speed of 8 meters per second, it delivers efficient cuts through various wood types.

One of the standout features of this chainsaw is its compatibility with the Worx PowerShare ecosystem. Users can utilize any 20V Max WORX battery, offering flexibility and convenience for those who already own other tools in the line. The machine includes an automatic oiler to keep the chain lubricated during operation, reducing wear and tear while maintaining safety. Safety is prioritized with a chain brake that activates instantly upon kickback, protecting the operator from sudden recoil.

The ergonomic design ensures comfort during extended use. The front handle and rear grip are positioned for optimal control, allowing users to maintain a firm hold even when cutting difficult timber. The tool also features a clear oil level window, making it easy to monitor fluid levels before and during work. Whether you are clearing storm debris or preparing firewood, the Worx WG384 offers a clean, quiet, and powerful solution.

Important Notes

  • Always wear protective gear including eye protection and hearing guards.
  • Ensure the chain is properly tensioned before each use to prevent accidents.
  • Charge both batteries simultaneously for balanced power output.
  • Never operate the saw above shoulder height or on unstable surfaces like ladders.
M: QW-35-FL

© Copyright 2026 Manual.ly