Manual.ly Logo

Worx WG384E Manual

0.0 · 0 Ratings

PDF manual · 88 Pages

English

M: QW-35-FL
page

/ 88

Loading...
c7b50bdbc36f698af3a7a103bdd313789403 page 8
8
Cordless Chain Saw
EN
GENERAL POWER TOOL
SAFETY WARNINGS
WARNING: Read all safety warnings and
all instructions. Failure to follow the
warnings and instructions may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future
reference.
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-
operated (cordless) power tool.
1. WORK AREA SAFETY
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b)
Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can
cause you to lose control.
2. ELECTRICAL SAFETY
a)
Power tool plugs must match the outlet.
Never modify the plug in any way. Do
not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or
grounded surfaces, such as pipes,
radiators, ranges and refrigerators. There is
an increased risk of electric shock if your body is
earthed or grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d)
Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the
power tool. Keep cord away from heat, oil,
sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use
an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces
the risk of electric shock.
f) If operating a power tool in a damp
location is unavoidable, use a residual
current device (RCD) protected supply. Use
of an RCD reduces the risk of electric shock.
3. PERSONAL SAFETY
a) Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use a power tool while
you are tired or under the influence of
drugs, alcohol or medication. A moment of
inattention while operating power tools may
result in serious personal injury.
b)
Use personal protective equipment. Always
wear eye protection. Protective equipment
such as dust mask, non-skid safety shoes, hard
hat, or hearing protection used for appropriate
conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure
the switch is in the off-position before
connecting to power source and/or battery
pack, picking up or carrying the tool.
Carrying power tools with your finger on the
switch or energising power tools that have the
switch on invites accidents.
d) Remove any adjusting key or wrench
before turning the power tool on. A wrench
or a key left attached to a rotating part of the
power tool may result in personal injury.
e)
Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing
or jewellery. Keep your hair, clothing and
gloves away from moving parts. Loose
clothes, jewellery or long hair can be caught in
moving parts.
g) If devices are provided for the connection
of dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust collection can reduce dust-
related hazards.
4. POWER TOOL USE AND CARE
a) Do not force the power tool. Use the
correct power tool for your application.
The correct power tool will do the job better and
safer at the rate for which it was designed.
b) Do not use the power tool if the switch
does not turn it on and off. Any power tool
that cannot be controlled with the switch is
dangerous and must be repaired.
c) Disconnect the plug from the power
source and/or the battery pack from the
power tool before making any adjustments,
changing accessories, or storing power
13
Z
Y
kg
Z
Y
a
Injecting grease to lubricate
TS
R
Q
PO
U

Chat with your Worx WG384E manual using AI

Get instant AI answers from your Worx WG384E manual

Ask anything about the Worx WG384E. Answers come from this manual, with the pages they are based on.

WG384E Maintenance Schedule

After each use
Inspect and clean the chainsaw

Remove battery pack. Inspect for damage, alignment, or binding. Clean sawdust from guide bar and sprocket hole.

Show in the manual (page 19)
Every time chain is removed
Clean guide bar rails

Use a wire brush or similar tool to clear residue from inner groove of the bar and clean oil passages thoroughly.

Show in the manual (page 20)
Each time chain is sharpened
Check guide bar condition

Inspect the guide bar for wear, bending, cracking, or excess heating/burring. Replace if damaged.

Show in the manual (page 20)
Regular intervals
Test chain brake function

Perform a function check by activating and deactivating the chain brake via the front hand guard.

Show in the manual (page 18)
Before starting and regularly during operation
Check oil level

Verify oil level window before starting and regularly while operating. Refill when low.

Show in the manual (page 18)
Every 10 minutes during operation
Check new chain tension

If the chain was recently replaced, check its tension every 10 minutes during operation.

Show in the manual (page 18)
As needed (when dull)
Sharpen or replace saw chain

Keep chain sharp. If cutting creates only sawdust or requires forcing, sharpen or replace the chain.

Show in the manual (page 20)
M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend WG384E?

Yes No

Frequently Asked Questions

A

No, the Worx WG384 requires two battery packs to function. The machine will not start unless both battery slots are filled with compatible 20V Max batteries.

Is this answer helpful?

A

If the chain can be lifted more than half the depth of the drive link off the guide bar, it is too loose. New chains stretch quickly so check tension often during the first few uses.

Is this answer helpful?

A

You must use standard bar and chain oil (ISO VG32). Do not use recycled oil or motor oil as this can damage the automatic oiler and void your warranty.

Is this answer helpful?

A

Absolutely not. The manual strictly warns against operating the chainsaw while in a tree. Always stand on solid, level ground to ensure stability and safety.

Is this answer helpful?

A

Runtime varies based on cutting intensity but a full charge typically lasts about 12 minutes of continuous cutting. Using two batteries helps extend total work time.

Is this answer helpful?

A

No, this chainsaw is intended only for cutting wood. Using it on plastic, masonry, or other non-wood materials is dangerous and can cause severe damage to the tool.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Compatible with all WORX 20V Max PowerShare batteries for maximum flexibility
  • Automatic chain lubrication system reduces maintenance and extends chain life
  • Integrated chain brake provides immediate safety protection against kickback
  • Lightweight design at 3.9 kg makes it easy to maneuver and carry
  • Clear oil level window allows for quick and easy monitoring of lubricant
VS

Disadvantages

  • Requires two batteries to operate which may increase initial setup cost
  • Chain tension must be checked frequently as new chains stretch quickly
  • Not suitable for cutting mineral materials or non-wood building components
  • Battery runtime depends on load intensity and may require spare packs for large jobs
  • Oil tank capacity is limited to 150 ml requiring frequent refills on heavy tasks
M: QW-35-FL

Product Specification

Type

Chainsaw

Bar Length

13.78 in

Chain Speed

26.25 ft/s

Chain Pitch

3/8"

Oil Tank Capacity

5.07 fl oz

Features

Battery level indicator, auxiliary handle, brushless motor, tool-free chain tensioning, automatic chain lubrication, chain brake, claw stop

Vibration Level

11.15 ft/s²

Noise Emission

96dB(A)

M: QW-35-FL

Product Description

Worx WG384 40V PowerShare Chainsaw Review

The Worx WG384 40V PowerShare Chainsaw is a versatile cordless tool designed for homeowners and professionals who need reliable wood cutting power without the hassle of cords or gasoline. This battery-powered saw features a robust 40-volt system powered by two 20V Max lithium-ion batteries, ensuring high performance for felling trees, limbing branches, and bucking logs. With a 14-inch guide bar and a chain speed of 8 meters per second, it delivers efficient cuts through various wood types.

One of the standout features of this chainsaw is its compatibility with the Worx PowerShare ecosystem. Users can utilize any 20V Max WORX battery, offering flexibility and convenience for those who already own other tools in the line. The machine includes an automatic oiler to keep the chain lubricated during operation, reducing wear and tear while maintaining safety. Safety is prioritized with a chain brake that activates instantly upon kickback, protecting the operator from sudden recoil.

The ergonomic design ensures comfort during extended use. The front handle and rear grip are positioned for optimal control, allowing users to maintain a firm hold even when cutting difficult timber. The tool also features a clear oil level window, making it easy to monitor fluid levels before and during work. Whether you are clearing storm debris or preparing firewood, the Worx WG384 offers a clean, quiet, and powerful solution.

Important Notes

  • Always wear protective gear including eye protection and hearing guards.
  • Ensure the chain is properly tensioned before each use to prevent accidents.
  • Charge both batteries simultaneously for balanced power output.
  • Never operate the saw above shoulder height or on unstable surfaces like ladders.
M: QW-35-FL

© Copyright 2026 Manual.ly