Manual.ly Logo

Worx WG384E Manual

0.0 · 0 Ratings

PDF manual · 88 Pages

English

M: QW-35-FL
page

/ 88

Loading...
c7b50bdbc36f698af3a7a103bdd313789403 page 13
19
Cordless Chain Saw
EN
wrap around saw handles. (See Fig. N)
(4) Make sure your footing is firm. Keep feet-shoulder
width apart. Distribute your weight evenly on both
feet.
(5) When ready to make a cut, push the lock-out
button completely in with the right thumb and
squeeze the trigger. This will turn saw on. Releasing
the trigger will turn the saw off. Make sure the saw
is running at full speed before starting a cut.
(6) When starting a cut, slowly place moving chain
against the wood. The wood should be as close to
the saw body as possible. Hold saw firmly in place
to avoid possible bouncing or skating (sideways
movement) of saw.
(7) Guide the saw using light pressure and do not put
excessive force on the saw, letting the saw do its
work. The motor will overload and can burn out.
It will do the job better and safer at the rate for
which it was intended.
(8) Remove the saw from a cut with the saw running
at full speed. Stop the saw by releasing the on/off
switch. Make sure the chain has stopped before
setting the saw down.
(9) Keep practicing on scrap logs in a secure working
area until you are comfortable, using a fluid
motion and a steady cutting rate.
Kickback Safety Devices On This Saw
This saw has a low-kickback chain and reduced
kickback Guide Bar. Both items reduce the chance of
kickback. However, kickback can still occur with this
saw.
The following steps will reduce the risk of kickback.
• Use both hands to grip saw while saw is running.
Use firm grip. Thumbs and fingers must wrap
around saw handles.
• Keep all safety items in place on saw. Make sure
they work properly.
• Do not overreach or cut above shoulder height.
• Keep solid footing and balance at all times.
• Stand slightly to the left side of saw. This keeps
your body from being in direct line with chain.
• Do not let Guide Bar nose touch anything when
chain is moving.
• Never try cutting through two logs at same time.
Only cut one log at a time.
• Do not bury the Guide Bar nose or try plunge cut
(boring into wood using guide bar nose).
• Watch for shifting of wood or other forces that
may pinch chain.
• Use extreme caution when reentering a previous
cut.
• Use only the low-kickback chain and guide
bar that were supplied with this Chainsaw or
recommended.
• Never use a dull or loose chain. Keep chain sharp
with proper tension.
How to use Saw Safely
1. Use the Chainsaw only with secure footing.
2. Hold the Chainsaw at the right-hand side of your
body (See Fig. O).
3. The chain must be running at full speed before it
makes contact with the wood.
4. Use the bumper spikes to secure the saw onto the
wood before starting to cut.
5. Use the Bumper Spikes as a leverage point while
cutting. (See Fig. P)
6. Do not operate the Chainsaw with arms fully
extended, attempt to saw areas which are difficult
to reach, or stand on a ladder while sawing (See
Fig. Q).
Never use the Chainsaw above shoulder height
Cutting wood under tension (See Fig. R)
WARNING: When cutting a limb that is
under tension, use extreme caution. Be
alert for wood springing back. When wood
tension is released, limb could spring back and
strike operator causing severe injury or death.
When sawing logs supported on both ends, start
the cut from above(Y) about 1/3 of the diameter into
the log (overbuck) and then finish the cut (Z) from
below, in order to avoid contact of the Chainsaw with
the ground. When sawing logs supported on only
one end, start the cut from below (Y) about 1/3 of
the diameter into the log (underbuck) and finish the
cut from above (Z) in order to avoid log splitting or
jamming of the Chainsaw.
SAW MAINTENANCE
Follow maintenance instructions in this manual.
Proper cleaning of saw and chain and Guide Bar
maintenance can reduce chances of kickback. Inspect
and maintain saw after each use. This will increase the
service life of your saw.
NOTE: Even with proper sharpening, risk of kickback
can increase with each sharpening.
MAINTENANCE AND
STORAGE OF Chainsaw
1. Remove the battery pack
• When not in use
• Before moving from one place to another
• Before servicing
• Before changing accessories or attachments, such
as saw chain and guard
2. Inspect Chainsaw before and after each use.
Check saw closely if guard or other part has been
damaged. Check for any damage that may affect
operator safety or operation of saw. Check for
alignment or binding of moving parts. Check for
broken or damaged parts. Do not use Chainsaw if
damage affects safety or operation. Have damage
repaired by authorized service center. To locate an
authorized service center, visit www.worx.com.
3. Maintain Chainsaw with care.
• Never expose saw to rain or direct moisture.
• Keep chain sharp, clean, and lubricated for better
and safer performance.

Chat with your Worx WG384E manual using AI

Get instant AI answers from your Worx WG384E manual

Ask anything about the Worx WG384E. Answers come from this manual, with the pages they are based on.

WG384E Maintenance Schedule

After each use
Inspect and clean the chainsaw

Remove battery pack. Inspect for damage, alignment, or binding. Clean sawdust from guide bar and sprocket hole.

Show in the manual (page 19)
Every time chain is removed
Clean guide bar rails

Use a wire brush or similar tool to clear residue from inner groove of the bar and clean oil passages thoroughly.

Show in the manual (page 20)
Each time chain is sharpened
Check guide bar condition

Inspect the guide bar for wear, bending, cracking, or excess heating/burring. Replace if damaged.

Show in the manual (page 20)
Regular intervals
Test chain brake function

Perform a function check by activating and deactivating the chain brake via the front hand guard.

Show in the manual (page 18)
Before starting and regularly during operation
Check oil level

Verify oil level window before starting and regularly while operating. Refill when low.

Show in the manual (page 18)
Every 10 minutes during operation
Check new chain tension

If the chain was recently replaced, check its tension every 10 minutes during operation.

Show in the manual (page 18)
As needed (when dull)
Sharpen or replace saw chain

Keep chain sharp. If cutting creates only sawdust or requires forcing, sharpen or replace the chain.

Show in the manual (page 20)
M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend WG384E?

Yes No

Frequently Asked Questions

A

No, the Worx WG384 requires two battery packs to function. The machine will not start unless both battery slots are filled with compatible 20V Max batteries.

Is this answer helpful?

A

If the chain can be lifted more than half the depth of the drive link off the guide bar, it is too loose. New chains stretch quickly so check tension often during the first few uses.

Is this answer helpful?

A

You must use standard bar and chain oil (ISO VG32). Do not use recycled oil or motor oil as this can damage the automatic oiler and void your warranty.

Is this answer helpful?

A

Absolutely not. The manual strictly warns against operating the chainsaw while in a tree. Always stand on solid, level ground to ensure stability and safety.

Is this answer helpful?

A

Runtime varies based on cutting intensity but a full charge typically lasts about 12 minutes of continuous cutting. Using two batteries helps extend total work time.

Is this answer helpful?

A

No, this chainsaw is intended only for cutting wood. Using it on plastic, masonry, or other non-wood materials is dangerous and can cause severe damage to the tool.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Compatible with all WORX 20V Max PowerShare batteries for maximum flexibility
  • Automatic chain lubrication system reduces maintenance and extends chain life
  • Integrated chain brake provides immediate safety protection against kickback
  • Lightweight design at 3.9 kg makes it easy to maneuver and carry
  • Clear oil level window allows for quick and easy monitoring of lubricant
VS

Disadvantages

  • Requires two batteries to operate which may increase initial setup cost
  • Chain tension must be checked frequently as new chains stretch quickly
  • Not suitable for cutting mineral materials or non-wood building components
  • Battery runtime depends on load intensity and may require spare packs for large jobs
  • Oil tank capacity is limited to 150 ml requiring frequent refills on heavy tasks
M: QW-35-FL

Product Specification

Type

Chainsaw

Bar Length

13.78 in

Chain Speed

26.25 ft/s

Chain Pitch

3/8"

Oil Tank Capacity

5.07 fl oz

Features

Battery level indicator, auxiliary handle, brushless motor, tool-free chain tensioning, automatic chain lubrication, chain brake, claw stop

Vibration Level

11.15 ft/s²

Noise Emission

96dB(A)

M: QW-35-FL

Product Description

Worx WG384 40V PowerShare Chainsaw Review

The Worx WG384 40V PowerShare Chainsaw is a versatile cordless tool designed for homeowners and professionals who need reliable wood cutting power without the hassle of cords or gasoline. This battery-powered saw features a robust 40-volt system powered by two 20V Max lithium-ion batteries, ensuring high performance for felling trees, limbing branches, and bucking logs. With a 14-inch guide bar and a chain speed of 8 meters per second, it delivers efficient cuts through various wood types.

One of the standout features of this chainsaw is its compatibility with the Worx PowerShare ecosystem. Users can utilize any 20V Max WORX battery, offering flexibility and convenience for those who already own other tools in the line. The machine includes an automatic oiler to keep the chain lubricated during operation, reducing wear and tear while maintaining safety. Safety is prioritized with a chain brake that activates instantly upon kickback, protecting the operator from sudden recoil.

The ergonomic design ensures comfort during extended use. The front handle and rear grip are positioned for optimal control, allowing users to maintain a firm hold even when cutting difficult timber. The tool also features a clear oil level window, making it easy to monitor fluid levels before and during work. Whether you are clearing storm debris or preparing firewood, the Worx WG384 offers a clean, quiet, and powerful solution.

Important Notes

  • Always wear protective gear including eye protection and hearing guards.
  • Ensure the chain is properly tensioned before each use to prevent accidents.
  • Charge both batteries simultaneously for balanced power output.
  • Never operate the saw above shoulder height or on unstable surfaces like ladders.
M: QW-35-FL

© Copyright 2026 Manual.ly