Manual.ly Logo

Worx WX712 Manual

0.0 · 0 Ratings

PDF manual · 92 Pages

English

M: OA-GPT-54-NAN
page

/ 92

Loading...
6ea6357a01e59480a8c9e63a4b4151f708c0 page 8
Angle Grinder EN
8
SAFETY INSTRUCTIONS
FOR ALL OPERATIONS
SAFETY WARNINGS COMMON FOR GRINDING
OR ABRASIVE CUTTING-OFF OPERATIONS:
a) This power tool is intended to function as
a grinder, or cut-off tool. Read all safety
warnings, instructions, illustrations and
specifications provided with this power
tool. Failure to follow all instructions listed below
may result in electric shock, fire and/or serious
injury.
b) Operations such as sanding, wire brushing,
polishing are not recommended to be
performed with this power tool. Operations
for which the power tool was not designed may
create a hazard and cause personal injury.
c) Do not use accessories which are not
specifically designed and recommended
by the tool manufacturer. Just because the
accessory can be attached to your power tool, it
does not assure safe operation.
d) The rated speed of the accessory must
be at least equal to the maximum speed
marked on the power tool. Accessories
running faster than their rated speed can break
and fly apart.
e) The outside diameter and the thickness of
your accessory must be within the capacity
rating of your power tool. Incorrectly sized
accessories cannot be adequately guarded or
controlled.
f) Threaded mounting of accessories must
match the grinder spindle thread. For
accessories mounted by flanges, the arbour
hole of the accessory must fit the locating
diameter of the flange. Accessories that do not
match the mounting hardware of the power tool
will run out of balance, vibrate excessively and
may cause loss of control.
g) Do not use a damaged accessory. Before
each use inspect the accessory such as
abrasive wheels for chips and cracks,
backing pad for cracks, tear or excess
wear. If power tool or accessory is
dropped, inspect for damage or install an
undamaged accessory. After inspecting and
installing an accessory, position yourself
and bystanders away from the plane of the
rotating accessory and run the power tool
at maximum no-load speed for one minute.
Damaged accessories will normally break apart
during this test time.
h) Wear personal protective equipment.
Depending on application, use face
shield, safety goggles or safety glasses.
As appropriate, wear dust mask, hearing
protectors, gloves and workshop apron
capable of stopping small abrasive or
workpiece fragments. The eye protection must
be capable of stopping flying debris generated by
various operations . The dust mask or respirator
must be capable of filtrating particles generated
by your operation. Prolonged exposure to high
intensity noise may cause hearing loss.
i) Keep bystanders a safe distance away from
work area. Anyone entering the work area
must wear personal protective equipment.
Fragments of workpiece or of a broken accessory
may fly away and cause injury beyond immediate
area of operation.
j) Hold power tool by insulated gripping
surfaces only, when performing an
operation where the cutting accessory
may contact hidden wiring or its own cord.
Cutting accessory contacting a “live” wire may
make exposed metal parts of the power tool
“live” and could give the operator an electric
shock
k) Position the cord clear of the spinning
accessory. If you lose control, the cord may be
cut or snagged and your hand or arm may be
pulled into the spinning accessory.
l) Never lay the power tool down until the
accessory has come to a complete stop.
The spinning accessory may grab the surface and
pull the power tool out of your control.
m) Do not run the power tool while carrying
it at your side. Accidental contact with the
spinning accessory could snag your clothing,
pulling the accessory into your body.
n) Regularly clean the power tool’s air vents.
The motor’s fan will draw the dust inside
the housing and excessive accumulation of
powdered metal may cause electrical hazards.
o) Do not operate the power tool near
flammable materials. Sparks could ignite these
materials.
p) Do not use accessories that require liquid
coolants. Using water or other liquid coolants
may result in electrocution or shock.
q) Your hand must hold on the handle when you
are working. Always use the auxiliary handles
supplied with the tool. Loss of control can cause
personal injury
FURTHER SAFETY INSTRUCTIONS FOR ALL
OPERATIONS
Kickback and Related Warnings
Kickback is a sudden reaction to a pinched or
snagged rotating wheel, backing pad, brush or
any other accessory. Pinching or snagging causes

Chat with your Worx WX712 manual using AI

Get instant AI answers from your Worx WX712 manual

Ask anything about the Worx WX712. Answers come from this manual, with the pages they are based on.

WX712 Maintenance Schedule

Regularly
Clean ventilation slots

Keep motor ventilation slots clean to prevent dust accumulation which may cause electrical hazards. Use non-metallic objects to remove dust.

Show in the manual (page 11)
Before each use
Inspect accessory for damage

Check abrasive wheels for chips and cracks, backing pad for tears or wear before every operation to ensure safe use.

M: QW-35-FL

Ask a Question

0/1000

Do you recommend WX712?

Yes No

Frequently Asked Questions

A

It is designed for cutting, rough grinding, and brushing metal and stone materials without water. It works best on general workshop and DIY tasks where a compact angle grinder is needed.

Is this answer helpful?

A

No. The tool is not recommended for sanding, polishing, or wire brushing. It is intended mainly for grinding and cutting operations using the proper discs and guard.

Is this answer helpful?

A

The WX712 uses 125 mm discs, which offer a practical balance between control and working capacity for common grinding and cutting jobs.

Is this answer helpful?

A

Yes. It includes a protective guard system and an auxiliary handle, and the design emphasizes safe control during operation. However, safe use still depends on correct accessories and protective equipment.

Is this answer helpful?

A

It is relatively light at about 2.0 kg, and the anti-vibration auxiliary handle helps improve comfort. Even so, vibration and noise mean it is best to take regular breaks and use proper safety gear.

Is this answer helpful?

A

Check that the disc is undamaged, the guard is fitted correctly, the outer flange is tight, and the tool is unplugged before changing accessories. Also make sure the workpiece is secure.

Is this answer helpful?

M: OA-GPT-54-NAN

Advantages and Disadvantages

Advantages

  • Strong 860W motor for everyday cutting and grinding tasks.
  • Light 2.0 kg body helps reduce strain during longer sessions.
  • Anti-vibration auxiliary handle improves comfort and control.
  • 125 mm disc size offers good versatility for common workshop jobs.
VS

Disadvantages

  • Not intended for sanding, polishing, or wire brushing tasks.
  • Requires careful setup and the correct guard for each operation.
  • Noise and vibration levels mean protective gear is necessary.
  • Best results depend on proper discs, technique, and maintenance.
M: OA-GPT-54-NAN

Product Specification

Type

Angle grinder

Power

860W (230V)

No-load speed

12000/min

Disc diameter

4.92 in

Tool mounting

M14 spindle thread, Spindle lock

Features

Softgrip, Auxiliary handle, Vibration damping

Weight

4.41 lb

Scope of delivery

Grinding disc

M: OA-GPT-54-NAN

Product Description

Worx WX712 Electric Angle Grinder: Compact Power for Everyday Metalwork

The Worx WX712 Electric angle grinder Manual points to a tool built for practical workshop tasks, and the WX712 itself reflects that idea well. Designed for cutting, rough grinding, and brushing metal and stone without water, this angle grinder aims to balance power, control, and portability in one compact package.

With a 860W motor, the WX712 delivers a strong performance for a tool in this class. Its 12,000 RPM no-load speed helps it handle demanding jobs with confidence, while the 125 mm disc capacity gives it enough working area for common cutting and grinding tasks. At around 2.0 kg, it is light enough to handle comfortably during longer sessions, especially when working on edges, welds, or small fabrication jobs.

A useful feature is the anti-vibration auxiliary handle, which improves comfort and helps reduce fatigue during repeated use. The guard system is also designed with safety in mind, making it easier to set up the grinder for either grinding or cutting operations. The machine uses a standard spindle thread and includes essential accessories such as a spanner and grinding disc, so getting started is straightforward.

What stands out most is how clearly the WX712 focuses on controlled performance. This is not a multifunction tool trying to do everything; instead, it is a dedicated grinder for users who want reliable material removal and clean cuts. For DIY projects, home repairs, or light professional use, that focused design can be a real advantage.

Safety remains a major theme throughout the tool's setup and use. The grinder is intended for dry work only, and it should always be used with the proper guard, disc type, and protective gear. Like any angle grinder, it demands respect: correct disc selection, firm two-handed control, and careful work habits are essential for good results.

Notes

  • Best suited for metal and stone trimming, roughing, and brushing.
  • Use only the correct disc type and guard for the job.
  • Anti-vibration support helps during extended use.
  • Always follow safe operating practices and protective equipment guidelines.
M: OA-GPT-54-NAN

© Copyright 2026 Manual.ly