Manual.ly Logo

Worx WX423 Manual

0.0 · 0 Ratings

PDF manual · 64 Pages

English

M: QW-35-FL
page

/ 64

Loading...
3cbc95edebf1020fb58541726223ec95c817 page c
Electric Circular Saw EN
12
Wheels intended for a larger power tool
are not suitable for the higher speed of a
smaller tool and may burst.
g) The outside diameter and the
thickness of your accessory must
be within the capacity rating of your
power tool. Incorrectly sized accessories
cannot be adequately guarded or
controlled.
h) The arbour size of wheels and flanges
must properly fit the spindle of
the power tool. Wheels and flanges
with arbour holes that do not match the
mounting hardware of the power tool will
run out of balance, vibrate excessively and
may cause loss of control.
i) Do not use damaged wheels. Before
each use, inspect the wheels for chips
and cracks. If power tool or wheel is
dropped, inspect for damage or install
an undamaged wheel. After inspecting
and installing the wheel, position
yourself and bystanders away from
the plane of the rotating wheel and
run the power tool at maximum no
load speed for one minute. Damaged
wheels will normally break apart during
this test time.
j) Wear personal protective equipment.
Depending on application, use face
shield, safety goggles or safety
glasses. As appropriate, wear dust
mask, hearing protectors, gloves and
shop apron capable of stopping small
abrasive or workpiece fragments.
The eye protection must be capable of
stopping flying debris generated by various
operations. The dust mask or respirator
must be capable of filtrating particles
generated by your operation. Prolonged
exposure to high intensity noise may cause
hearing loss.
k) Keep bystanders a safe distance away
from work area. Anyone entering
the work area must wear personal
protective equipment. Fragments of
workpiece or of a broken wheel may fly
away and cause injury beyond immediate
area of operation.
I) Hold the power tool by insulated
gripping surfaces only, when
performing an operation where
the cutting accessory may contact
hidden wiring or its own cord. Cutting
accessory contacting a “live” wire may
make exposed metal parts of the power
tool “live” and could give the operator an
electric shock.
m) Position the cord clear of the spinning
accessory. lf you lose control, the cord
may be cut or snagged and your hand or
arm may be pulled into the spinning wheel.
n) Never lay the power tool down until
the accessory has come to a complete
stop. The spinning wheel may grab the
surface and pull the power tool out of your
control.
o) Do not run the power tool while
carrying it at your side. Accidental
contact with the spinning accessory could
snag your clothing, pulling the accessory
into your body.
p) Regularly clean the power tool’s air
vents. The motor’s fan will draw the
dust inside the housing and excessive
accumulation of powdered metal may
cause electrical hazards.
q) Do not operate the power tool near
flammable materials. Sparks could ignite
these materials.
r) Do not use accessories that require
liquid coolants. Using water or other
liquid coolants may result in electrocution
or shock.
KICKBACK AND RELATED
WARNINGS
Kickback is a sudden reaction to a pinched or
snagged rotating wheel. Pinching or snagging
causes rapid stalling of the rotating wheel
which in turn causes the uncontrolled power
tool to be forced in the direction opposite of
the wheel’s rotation at the point of the binding.
For example, if an abrasive wheel is snagged
or pinched by the workpiece, the edge of the
wheel that is entering into the pinch point can
dig into the surface of the material causing
the wheel to climb out or kick out. The wheel

Chat with your Worx WX423 manual using AI

Get instant AI answers from your Worx WX423 manual

Ask anything about the Worx WX423. Answers come from this manual, with the pages they are based on.

WX423 Maintenance Schedule

Before each use
Check lower guard function and spring operation

Ensure the lower guard moves freely and closes instantly. Check the spring operation; if sluggish or damaged, service before use.

Show in the manual (page 11)
Before each use
Inspect cutting wheels for damage

Inspect wheels for chips and cracks. If dropped, inspect for damage or install an undamaged wheel.

Show in the manual (page 12)
Regularly
Clean air vents

Regularly clean the power tool's air vents to prevent excessive accumulation of powdered metal which may cause electrical hazards.

Show in the manual (page 12)
Periodically
Inspect supply cord

Inspect tool cords periodically and if damaged, have repaired by authorized service facility.

Show in the manual (page 15)
Periodically
Clear dust from guard and base

Periodically clear dust and chips from guard and base to ensure proper performance.

Show in the manual (page 15)
M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend WX423?

Yes No

Frequently Asked Questions

A

The saw can cut wood up to 27mm, aluminum up to 3mm, PVC pipes with a 13mm radius, tiles up to 8mm, and sheet steel up to 0.91mm depending on the blade used.

Is this answer helpful?

A

Yes, the product description mentions it comes with a case along with accessories like blades and guides for convenient storage and transport.

Is this answer helpful?

A

Use the spindle lock button to hold the shaft steady and the included hex key to loosen the blade bolt. Replace the blade and tighten securely before use.

Is this answer helpful?

A

While specific warranty terms are not listed in the text, WORX products typically come with a manufacturer warranty. Check your local retailer for specific coverage details.

Is this answer helpful?

A

No, never use liquid coolants or water with this electric tool as it poses a risk of electric shock. Keep the tool dry at all times.

Is this answer helpful?

A

You must wear eye protection, hearing protection, and a dust mask. Gloves and a shop apron are also recommended for full body protection.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Compact and lightweight design at 1.4kg for easy handling
  • Versatile cutting capabilities for wood, metal, tile, and PVC
  • Includes multiple blades: TCT, HSS, and Diamond disc
  • Dust extraction outlet helps maintain a clean workspace
  • Soft grip handle reduces user fatigue during operation
VS

Disadvantages

  • Maximum cutting depth limited to 27mm may restrict thick material work
  • Requires separate purchase of additional specialized blades
  • Vibration levels require careful management to avoid hand-arm syndrome
  • Blade changes require a hex key which can be easily misplaced
  • Not suitable for very high volume industrial continuous use
M: QW-35-FL

Product Specification

Type

Mini plunge saw

Power

400W

No-load speed

3600/min

Blade diameter

3.35 inches

Cutting capacity

1.06 inches (cut depth at 0°)

Tool holder

15mm chuck

Features

Soft grip, parallel fence, dust extraction

Weight

3.09 lbs

Package contents

Case, 3-piece accessory set

M: QW-35-FL

Product Description

Worx WX423 Electric Mini Submersible Saw Review

The Worx WX423 Electric Mini Submersible Saw is a compact and powerful tool designed for precision cutting in tight spaces. With a rated power of 400W, this saw delivers efficient performance for various materials including wood, aluminum, PVC pipes, tiles, and thin sheet steel. Its lightweight design at just 1.4kg makes it easy to handle, while the soft grip handle ensures comfort during extended use.

This versatile circular saw features a spindle lock button for quick blade changes and an adjustable depth lever that allows cuts up to 27mm deep. The included parallel guide ensures straight cuts, making it ideal for DIY projects and professional tasks alike. The dust extraction outlet connects to a vacuum adapter for cleaner work environments. Safety is prioritized with a lower blade guard that retracts automatically and a lock-off button to prevent accidental starts.

The package includes essential accessories such as a TCT blade for wood, an HSS blade, a diamond disc for hard materials, a hex key, and a parallel guide. Whether you are cutting timber or trimming metal, the WX423 handles the job with ease. The no-load speed of 3600 RPM provides the necessary torque for smooth operation across different materials.

Users should always wear protective gear including eye protection, hearing protection, and a dust mask when operating this tool. Proper maintenance involves keeping the base plate clean and ensuring the blade is sharp. The tool complies with international safety standards and features double insulation for added user protection.

Important Notes

  • Always ensure the blade is secure before starting.
  • Use only recommended blades for specific materials.
  • Keep ventilation slots clean to prevent overheating.
M: QW-35-FL

© Copyright 2026 Manual.ly