Manual.ly Logo

T.I.P. AJ 4 Plus Series Manual

0.0 · 0 Ratings

PDF manual · 64 Pages

English

M: gpt-5.6-terra
page

/ 64

Loading...
b4505f43ffaaa3be0a00c497728a53047337 page 6
Originalgebrauchsanweisung
4
5.4. Positionierung der Pumpe
Zum Hinablassen oder Hochziehen der Pumpe darf nur ein geeignetes Ablassseil und keines-
falls der Druckschlauch oder das Anschlusskabel verwendet werden.
Die Pumpe darf nur mit einem dafür geeigneten Ablassseil in die Flüssigkeit hinabgelassen und hochgezogen
werden. Verwenden Sie ein Seil aus rostfreiem Stahl oder synthetischen Materialien wie Nylon. Seile, die in Folge
von Wettereinflüssen und Feuchtigkeit zu Rostbildung, Verwitterung, Fäulnis etc. neigen, dürfen wegen der damit
verbundenen Gefahr des Reißens nicht verwendet werden. Das Seil muss nicht nur das Gewicht der Pumpe, der
mit Wasser gefüllten Druckleitung und des Anschlusskabels tragen können, sondern zusätzlich den Belastungen
standhalten, die beim Betrieb auftreten. Die serienmäßige Ausstattung dieses Modells umfasst ein hochwertiges
Ablassseil (1).Zur Befestigung des Ablassseils dienen zwei Ösen (2) am oberen Teil der Pumpe.
Achten Sie darauf, dass sich die Pumpe in einer vertikalen Position ausrichtet, wenn sie am Seil angehoben wird.
Lassen Sie die Pumpe mit dem Ablassseil vorsichtig in die Förderflüssigkeit hinab. Beim Hinablassen muss die
Pumpe senkrecht ausgerichtet sein. Achten Sie darauf, dass das Gerät nicht gegen den Rand der Vertiefung
schlägt oder an diesem reibt. Die Pumpe muss vollständig in die Flüssigkeit eingetaucht werden. Der Abstand
zum Grund sollte im Betrieb mindestens 0,5 m betragen, um das Ansaugen, von Schlamm, Sand, Steinen etc. zu
verhindern.
Um diese Positionierung sicherzustellen wird empfohlen, die Pumpe auf den Grund des Brunnenschachts abzu-
lassen und die so gemessene Eintauchtiefe am gespannten Seil zu markieren. Machen sie eine zweite Markie-
rung 0,5 m unterhalb (Richtung Pumpe). Ziehen Sie nun die Pumpe 50 cm nach oben und fixieren Sie das Gerät
in dieser Position unter Berücksichtigung der zweiten Markierung. Bitte beachten Sie, dass die maximale Ein-
tauchtiefe der Pumpe in Flüssigkeit 20 m beträgt.
6. Elektrischer Anschluss
Das Gerät verfügt über ein Netzanschlusskabel mit Netzstecker. Netzanschlusskabel und Netzstecker dürfen nur
durch Fachpersonal ausgetauscht werden, um Gefährdungen zu vermeiden. Tragen Sie die Pumpe nicht am
Netzanschlusskabel, und benutzen Sie es nicht, um den Netzstecker aus der Steckdose zu ziehen. Schützen Sie
Netzstecker und Netzanschlusskabel vor Hitze, Öl und scharfen Kanten.
Die bei den technischen Daten genannten Werte müssen der vorhandenen Netzspannung
entsprechen. Die für die Installation verantwortliche Person muss sicherstellen, dass der elekt-
rische Anschluss über eine den Normen entsprechende Erdung verfügt.
Der elektrische Anschluss muss mit einem hoch empfindlichen Fehlerstromschutzschalter
(FI-Schalter) ausgestattet sein: ∆ = 30 mA (DIN VDE 0100-739).
Verlängerungskabel dürfen keinen geringeren Querschnitt haben als Gummischlauchleitungen
mit dem Kurzzeichen H07RN-F (3 x 1,0 mm²) nach VDE. Netzstecker und Kupplungen müs-
sen spritzwassergeschützt sein.
7. Inbetriebnahme
Während des Betriebs der Pumpe dürfen sich keine Personen im Wasser aufhalten.
Die Pumpe darf nur in dem Leistungsbereich verwendet werden, der auf dem Typenschild ge-
nannt ist.
Das Trockenlaufen - Betrieb der Pumpe, ohne Wasser zu fördern - muss verhindert werden,
da Wassermangel zum Heißlaufen der Pumpe führt. Dies kann zu erheblichen Schäden am
Gerät führen.
Stellen Sie sicher, dass sich die elektrischen Steckverbindungen in überflutungssicherem Be-
reich befinden.
Es ist absolut verboten, mit den Händen in die Öffnung der Pumpe zu greifen, wenn das Gerät
an das Stromnetz angeschlossen ist.
Die Pumpe darf nicht arbeiten, wenn der Druckanschluss oder die Druckleitung geschlossen
ist.
4

Chat with your T.I.P. AJ 4 Plus Series manual using AI

Get instant AI answers from your T.I.P. AJ 4 Plus Series manual

Ask anything about the T.I.P. AJ 4 Plus Series. Answers come from this manual, with the pages they are based on.

AJ 4 Plus Series Maintenance Schedule

Before each use
Visual inspection of pump and cable

Check the mains connection line and plug for damage. Ensure all screws are tight and connections are in perfect condition before every use.

As needed
Clean intake filter

If water is not clean, disconnect power and remove pump from water. Clean the outer surface with a steel brush or remove the stainless steel panel to clean inside.

M: QW-35-FL

Ask a Question

0/1000

Do you recommend AJ 4 Plus Series?

Yes No

Frequently Asked Questions

A

It is designed for clean water from deep wells, boreholes, cisterns, and storage tanks. Typical uses include garden irrigation, sprinkler systems, terrace cleaning, and non-potable domestic water supply.

Is this answer helpful?

A

The pump has a nominal power rating of 1,100 W, a maximum flow rate of 6,000 liters per hour, a maximum pressure of 5.7 bar, and a maximum delivery height of 57 meters.

Is this answer helpful?

A

The pump starts after connection to power and restarts when water use drops system pressure below about 3 bar. It shuts down after water demand stops and flow reaches a minimal level.

Is this answer helpful?

A

The maximum submersion depth is 20 meters. Position it vertically and keep it at least 0.5 meters above the well bottom to limit the intake of sediment and debris.

Is this answer helpful?

A

Its dry-run protection makes several pumping attempts, pauses between cycles, and eventually enters error mode if no water is available. Correct the cause, then unplug the pump for about 10 seconds to reset it.

Is this answer helpful?

A

No. It is not intended for drinking water or pool use. It must also not be used with saltwater, sewage, flammable, corrosive, explosive, or other hazardous liquids.

Is this answer helpful?

M: gpt-5.6-terra

Advantages and Disadvantages

Advantages

  • Delivers up to 6,000 l/h, with a maximum head of 57 m and pressure up to 5.7 bar.
  • Slim 9.8 cm diameter supports installation in narrow boreholes and deep well shafts.
  • Automatic control starts below about 3 bar and stops when demand ends.
  • Integrated dry-run, thermal motor, and non-return valve protection improve operating safety.
  • Includes a 23 m power cable and lowering rope for deep-well installation.
VS

Disadvantages

  • Suitable only for clean water with particles up to 2 mm; sand and abrasive debris increase wear.
  • Not intended for drinking water, swimming pools, saltwater, sewage, or hazardous liquids.
  • Maximum liquid temperature is limited to 35 C.
  • Requires a properly grounded electrical supply with a 30 mA RCD.
  • Dry-run fault mode requires manual reset after the water supply issue is corrected.
M: gpt-5.6-terra

Product Specification

Features

tankless

M: gpt-5.6-terra

Product Description

T.I.P. Electric Deep Well Pump Manual: Powerful Water Supply for Wells and Gardens

The T.I.P. Electric Deep Well Pump AJ 4 Plus 100/57 AUT is a compact submersible pressure pump designed to bring clean water up from deep wells, boreholes, cisterns, and storage tanks. With a slim 9.8 cm diameter body, it is particularly suitable for narrow shafts where larger pumps cannot fit. Its combination of strong pressure, automatic control, and protective features makes it a practical choice for private water supply and irrigation projects.

Powered by a 1,100 W motor, this model can deliver up to 6,000 liters per hour and reach a maximum delivery head of 57 meters. It produces up to 5.7 bar of pressure, supporting demanding tasks such as watering large gardens, operating sprinkler systems, washing terraces, and supplying non-potable household water. The pump is intended for clean, clear water containing particles no larger than 2 mm.

Automatic pressure-controlled operation

A major benefit highlighted in the T.I.P. Electric Deep Well Pump Manual is its integrated electronic control system. Once connected to power, the pump begins after an approximately 10-second delay. It starts automatically when water is drawn and system pressure drops below about 3 bar. When taps or connected consumers are closed, the unit stops after flow falls to a minimum level.

This automatic operation offers the convenience of a household water system without requiring a separate pressure vessel. The delayed shutoff, which can last up to 40 seconds, helps reduce excessive cycling during low-flow use. An integrated non-return valve also prevents water from flowing back into the pump after shutdown and helps protect the system from pressure surges.

Installation and operating protection

The pump can be submerged to a maximum depth of 20 meters and should be positioned at least 0.5 meters above the bottom of the well. This clearance helps reduce the intake of sludge, sand, and stones. A 23-meter power cable and lowering rope are supplied, while the pressure hose or pipe should match at least the 1-inch outlet diameter.

Built-in dry-run protection and thermal motor protection add reassurance during normal operation. If water is unavailable, the pump makes repeated restart attempts before entering an error mode. After the cause is corrected, disconnecting power for around 10 seconds resets the system. The intake filter can be cleaned when needed, but internal repairs should be left to authorized service personnel.

Note: This pump is for private applications and clean, non-drinking water only. Do not use it for swimming pools, saltwater, sewage, flammable liquids, or liquids above 35 C. Use a properly grounded supply protected by a 30 mA RCD.

M: gpt-5.6-terra

© Copyright 2026 Manual.ly