T.I.P. AJ 4 Plus Series Manual
PDF manual · 64 Pages
English

Quick check
Incorrect answer, please try again.
Chat with your T.I.P. AJ 4 Plus Series manual using AI
Get instant AI answers from your T.I.P. AJ 4 Plus Series manual
Ask anything about the T.I.P. AJ 4 Plus Series. Answers come from this manual, with the pages they are based on.
AJ 4 Plus Series Maintenance Schedule
Check the mains connection line and plug for damage. Ensure all screws are tight and connections are in perfect condition before every use.
If water is not clean, disconnect power and remove pump from water. Clean the outer surface with a steel brush or remove the stainless steel panel to clean inside.
Ask a Question
Do you recommend AJ 4 Plus Series?
Yes NoFrequently Asked Questions
It is designed for clean water from deep wells, boreholes, cisterns, and storage tanks. Typical uses include garden irrigation, sprinkler systems, terrace cleaning, and non-potable domestic water supply.
Is this answer helpful?
The pump has a nominal power rating of 1,100 W, a maximum flow rate of 6,000 liters per hour, a maximum pressure of 5.7 bar, and a maximum delivery height of 57 meters.
Is this answer helpful?
The pump starts after connection to power and restarts when water use drops system pressure below about 3 bar. It shuts down after water demand stops and flow reaches a minimal level.
Is this answer helpful?
The maximum submersion depth is 20 meters. Position it vertically and keep it at least 0.5 meters above the well bottom to limit the intake of sediment and debris.
Is this answer helpful?
Its dry-run protection makes several pumping attempts, pauses between cycles, and eventually enters error mode if no water is available. Correct the cause, then unplug the pump for about 10 seconds to reset it.
Is this answer helpful?
No. It is not intended for drinking water or pool use. It must also not be used with saltwater, sewage, flammable, corrosive, explosive, or other hazardous liquids.
Is this answer helpful?
Advantages and Disadvantages
Advantages
- Delivers up to 6,000 l/h, with a maximum head of 57 m and pressure up to 5.7 bar.
- Slim 9.8 cm diameter supports installation in narrow boreholes and deep well shafts.
- Automatic control starts below about 3 bar and stops when demand ends.
- Integrated dry-run, thermal motor, and non-return valve protection improve operating safety.
- Includes a 23 m power cable and lowering rope for deep-well installation.
Disadvantages
- Suitable only for clean water with particles up to 2 mm; sand and abrasive debris increase wear.
- Not intended for drinking water, swimming pools, saltwater, sewage, or hazardous liquids.
- Maximum liquid temperature is limited to 35 C.
- Requires a properly grounded electrical supply with a 30 mA RCD.
- Dry-run fault mode requires manual reset after the water supply issue is corrected.
Product Specification
Features
tankless
Product Description
T.I.P. Electric Deep Well Pump Manual: Powerful Water Supply for Wells and Gardens
The T.I.P. Electric Deep Well Pump AJ 4 Plus 100/57 AUT is a compact submersible pressure pump designed to bring clean water up from deep wells, boreholes, cisterns, and storage tanks. With a slim 9.8 cm diameter body, it is particularly suitable for narrow shafts where larger pumps cannot fit. Its combination of strong pressure, automatic control, and protective features makes it a practical choice for private water supply and irrigation projects.
Powered by a 1,100 W motor, this model can deliver up to 6,000 liters per hour and reach a maximum delivery head of 57 meters. It produces up to 5.7 bar of pressure, supporting demanding tasks such as watering large gardens, operating sprinkler systems, washing terraces, and supplying non-potable household water. The pump is intended for clean, clear water containing particles no larger than 2 mm.
Automatic pressure-controlled operation
A major benefit highlighted in the T.I.P. Electric Deep Well Pump Manual is its integrated electronic control system. Once connected to power, the pump begins after an approximately 10-second delay. It starts automatically when water is drawn and system pressure drops below about 3 bar. When taps or connected consumers are closed, the unit stops after flow falls to a minimum level.
This automatic operation offers the convenience of a household water system without requiring a separate pressure vessel. The delayed shutoff, which can last up to 40 seconds, helps reduce excessive cycling during low-flow use. An integrated non-return valve also prevents water from flowing back into the pump after shutdown and helps protect the system from pressure surges.
Installation and operating protection
The pump can be submerged to a maximum depth of 20 meters and should be positioned at least 0.5 meters above the bottom of the well. This clearance helps reduce the intake of sludge, sand, and stones. A 23-meter power cable and lowering rope are supplied, while the pressure hose or pipe should match at least the 1-inch outlet diameter.
Built-in dry-run protection and thermal motor protection add reassurance during normal operation. If water is unavailable, the pump makes repeated restart attempts before entering an error mode. After the cause is corrected, disconnecting power for around 10 seconds resets the system. The intake filter can be cleaned when needed, but internal repairs should be left to authorized service personnel.
Note: This pump is for private applications and clean, non-drinking water only. Do not use it for swimming pools, saltwater, sewage, flammable liquids, or liquids above 35 C. Use a properly grounded supply protected by a 30 mA RCD.
Search for 67,706 Manuals online
Type-in Brand or Model