Manual.ly Logo

T.I.P. AJ 4 Plus Series Manual

0.0 · 0 Ratings

PDF manual · 64 Pages

English

M: gpt-5.6-terra
page

/ 64

Loading...
b4505f43ffaaa3be0a00c497728a53047337 page 5
Originalgebrauchsanweisung
3
Die Pumpe eignet sich nicht zur Förderung von Salzwasser, Fäkalien, entflammbaren, ätzen-
den, explosiven oder anderen gefährlichen Flüssigkeiten. Die Förderflüssigkeit darf die bei
den technischen Daten genannte Höchsttemperatur nicht überschreiten.
In der Pumpe kommen Schmiermittel zum Einsatz, die bei unsachgemäßem Gebrauch oder
bei Beschädigungen des Geräts die Förderflüssigkeit verschmutzen können. Die eingesetzten
Schmiermittel sind biologisch abbaubar und gesundheitlich unbedenklich.
4. Lieferumfang
Im Lieferumfang dieses Produkts sind enthalten:
Eine Pumpe mit Anschlusskabel, ein Ablassseil, eine Gebrauchsanweisung.
Überprüfen Sie den Lieferumfang auf Vollständigkeit. Je nach Anwendungszweck kann weiteres Zubehör erfor-
derlich sein (siehe Kapitel „Installation“, „Automatisierung mit Spezialzubehör“ und „Bestellung von Ersatzteilen“).
Bewahren Sie die Verpackung nach Möglichkeit bis zum Ablauf der Garantiezeit auf. Entsorgen Sie Verpa-
ckungsmaterialien umweltgerecht.
5. Installation
5.1. Allgemeine Hinweise zur Installation
Während der gesamten Installation darf das Gerät nicht ans Stromnetz angeschlossen sein.
Die Pumpe und das gesamte Anschlusssystem müssen vor Frost geschützt werden.
Beachten Sie bitte auch die Abbildungen, die sich im Text, bzw. als Anhang am Ende dieser Gebrauchsanwei-
sung befinden. Die Zahlen, die in den nachfolgenden Ausführungen in Klammern genannt sind, beziehen sich auf
Abb. 5 am Ende der Gebrauchsanweisung.
Alle Anschlussleitungen müssen absolut dicht sein, da undichte Leitungen die Leistung der Pumpe beeinträchti-
gen und erhebliche Schäden herbeiführen können.
Verwenden Sie gegebenenfalls geeignetes Dichtungsmaterial, damit die Montage luftdicht erfolgt.
Vermeiden Sie beim Anziehen von Verschraubungen übermäßige Kraft, die zu Beschädigungen führen kann.
Achten Sie beim Verlegen der Anschlussleitungen darauf, dass kein Gewicht sowie keine Schwingungen oder
Spannungen auf die Pumpe einwirken. Außerdem dürfen die Anschlussleitungen keine Knicke oder ein Gegenge-
fälle aufweisen.
5.2. Installation der Druckleitung
Die Druckleitung befördert die Flüssigkeit, die gefördert werden soll, von der Pumpe zur Entnahmestelle. Zur
Vermeidung von Strömungsverlusten empfiehlt sich die Verwendung einer Druckleitung, die mindestens den glei-
chen Durchmesser hat wie der Druckanschluss (5) der Pumpe.
Als Druckleitung ist ein für diesen Verwendungszweck geeigneter flexibler Schlauch zu verwenden - beispielswei-
se ein speziell konzipierter Entwässerungsschlauch. Im Falle einer Festinstallation erweisen sich starre Rohre als
ideale Druckleitung.
Die Pumpe verfügt über ein integriertes Rückschlagventil. Es verhindert, dass nach Beendigung des Betriebs
Flüssigkeit aus der Druckleitung in die Pumpe zurückläuft, und bietet Schutz vor Beschädigungen des Geräts
durch Druckstöße.
Montieren Sie die Druckleitung an den Druckanschluss (5) der Pumpe.
5.3. Befestigen des Ablassseils
Führen Sie das im Lieferumfang enthaltene Ablassseil wie auf Abb.1 zu sehen, durch die zwei Ösen am oberen
Ende der Pumpe. Danach fixieren Sie das Seil mit einem doppelten Knoten (Abb.2). Achten Sie darauf, dass das
Ablassseil fest an der Pumpe fixiert ist.
Abb.1
Abb.2
3

Chat with your T.I.P. AJ 4 Plus Series manual using AI

Get instant AI answers from your T.I.P. AJ 4 Plus Series manual

Ask anything about the T.I.P. AJ 4 Plus Series. Answers come from this manual, with the pages they are based on.

AJ 4 Plus Series Maintenance Schedule

Before each use
Visual inspection of pump and cable

Check the mains connection line and plug for damage. Ensure all screws are tight and connections are in perfect condition before every use.

As needed
Clean intake filter

If water is not clean, disconnect power and remove pump from water. Clean the outer surface with a steel brush or remove the stainless steel panel to clean inside.

M: QW-35-FL

Ask a Question

0/1000

Do you recommend AJ 4 Plus Series?

Yes No

Frequently Asked Questions

A

It is designed for clean water from deep wells, boreholes, cisterns, and storage tanks. Typical uses include garden irrigation, sprinkler systems, terrace cleaning, and non-potable domestic water supply.

Is this answer helpful?

A

The pump has a nominal power rating of 1,100 W, a maximum flow rate of 6,000 liters per hour, a maximum pressure of 5.7 bar, and a maximum delivery height of 57 meters.

Is this answer helpful?

A

The pump starts after connection to power and restarts when water use drops system pressure below about 3 bar. It shuts down after water demand stops and flow reaches a minimal level.

Is this answer helpful?

A

The maximum submersion depth is 20 meters. Position it vertically and keep it at least 0.5 meters above the well bottom to limit the intake of sediment and debris.

Is this answer helpful?

A

Its dry-run protection makes several pumping attempts, pauses between cycles, and eventually enters error mode if no water is available. Correct the cause, then unplug the pump for about 10 seconds to reset it.

Is this answer helpful?

A

No. It is not intended for drinking water or pool use. It must also not be used with saltwater, sewage, flammable, corrosive, explosive, or other hazardous liquids.

Is this answer helpful?

M: gpt-5.6-terra

Advantages and Disadvantages

Advantages

  • Delivers up to 6,000 l/h, with a maximum head of 57 m and pressure up to 5.7 bar.
  • Slim 9.8 cm diameter supports installation in narrow boreholes and deep well shafts.
  • Automatic control starts below about 3 bar and stops when demand ends.
  • Integrated dry-run, thermal motor, and non-return valve protection improve operating safety.
  • Includes a 23 m power cable and lowering rope for deep-well installation.
VS

Disadvantages

  • Suitable only for clean water with particles up to 2 mm; sand and abrasive debris increase wear.
  • Not intended for drinking water, swimming pools, saltwater, sewage, or hazardous liquids.
  • Maximum liquid temperature is limited to 35 C.
  • Requires a properly grounded electrical supply with a 30 mA RCD.
  • Dry-run fault mode requires manual reset after the water supply issue is corrected.
M: gpt-5.6-terra

Product Specification

Features

tankless

M: gpt-5.6-terra

Product Description

T.I.P. Electric Deep Well Pump Manual: Powerful Water Supply for Wells and Gardens

The T.I.P. Electric Deep Well Pump AJ 4 Plus 100/57 AUT is a compact submersible pressure pump designed to bring clean water up from deep wells, boreholes, cisterns, and storage tanks. With a slim 9.8 cm diameter body, it is particularly suitable for narrow shafts where larger pumps cannot fit. Its combination of strong pressure, automatic control, and protective features makes it a practical choice for private water supply and irrigation projects.

Powered by a 1,100 W motor, this model can deliver up to 6,000 liters per hour and reach a maximum delivery head of 57 meters. It produces up to 5.7 bar of pressure, supporting demanding tasks such as watering large gardens, operating sprinkler systems, washing terraces, and supplying non-potable household water. The pump is intended for clean, clear water containing particles no larger than 2 mm.

Automatic pressure-controlled operation

A major benefit highlighted in the T.I.P. Electric Deep Well Pump Manual is its integrated electronic control system. Once connected to power, the pump begins after an approximately 10-second delay. It starts automatically when water is drawn and system pressure drops below about 3 bar. When taps or connected consumers are closed, the unit stops after flow falls to a minimum level.

This automatic operation offers the convenience of a household water system without requiring a separate pressure vessel. The delayed shutoff, which can last up to 40 seconds, helps reduce excessive cycling during low-flow use. An integrated non-return valve also prevents water from flowing back into the pump after shutdown and helps protect the system from pressure surges.

Installation and operating protection

The pump can be submerged to a maximum depth of 20 meters and should be positioned at least 0.5 meters above the bottom of the well. This clearance helps reduce the intake of sludge, sand, and stones. A 23-meter power cable and lowering rope are supplied, while the pressure hose or pipe should match at least the 1-inch outlet diameter.

Built-in dry-run protection and thermal motor protection add reassurance during normal operation. If water is unavailable, the pump makes repeated restart attempts before entering an error mode. After the cause is corrected, disconnecting power for around 10 seconds resets the system. The intake filter can be cleaned when needed, but internal repairs should be left to authorized service personnel.

Note: This pump is for private applications and clean, non-drinking water only. Do not use it for swimming pools, saltwater, sewage, flammable liquids, or liquids above 35 C. Use a properly grounded supply protected by a 30 mA RCD.

M: gpt-5.6-terra

© Copyright 2026 Manual.ly