Manual.ly Logo

Oase FiltoSmart 60 Manual

0.0 · 0 Ratings

PDF manual · 98 Pages

English

M: QW-35-FL
page

/ 98

Loading...
de634e5ecefd526039f1cb7c8d7970520119 page a
- DE -
10 FiltoSmart 60
STÖRUNGSBESEITIGUNG
Störung
Ursache
Abhilfe
Gerät läuft nicht an
Netzspannung fehlt
Netzspannung überprüfen
Laufeinheit blockiert
Reinigen
Wasserstand im Gerät zu niedrig
Wasser auffüllen
Wasserfluss ungenügend
Filtergehäuse oder Laufeinheit verschmutzt
Reinigen
Laufeinheit verschlissen
Laufeinheit ersetzen
Filterschaum verschmutzt
Reinigen
Keramiksubstrat verschmutzt
Reinigen
Saugkorb verstopft
Saugkorb reinigen
Leitungssystem verschmutzt
Saugeinheit, Ausströmeinheit und
Schläuche reinigen
Filterwirkung ungenügend
Filterschaum verschmutzt
Reinigen
Filterschaum verschlissen
Ersetzen
Keramiksubstrat verschmutzt
Reinigen
Keramiksubstrat verschlissen
Ersetzen
Erhöhte Geräuschentwicklung
Luft im Filter, Entlüfterschlauch an Pumpe nicht richtig
positioniert
Sitz des Entlüfterschlauches korri-
gieren.
REINIGUNG UND WARTUNG
• Gerät bei Bedarf mit klarem Wasser und mit einer
weichen Bürste reinigen.
• Keine Reinigungsmittel oder chemische Lösungen
verwenden. Um Kalkablagerungen zu entfernen,
wird OASE PumpClean empfohlen.
• Reinigungs- und Austauschzyklen für Filtermateria-
lien sind abhängig von Beckengröße und Besatz.
Reinigung und Austausch sollten daher nach Bedarf
erfolgen, um die volle Filterleistung sicherzustellen.
Filtermaterial reinigen/ersetzen
HINWEIS
Verpackung um Filtermaterial entfernen. Alle Filter-
materialien vor der ersten Verwendung mit warmem
Leitungswasser gründlich ausspülen, um mögliche Ver-
schmutzungen zu entfernen. (→ Filtermaterial reini-
gen/ersetzen)
Voraussetzung
• Der Gerätekopf ist abgenommen. (→ Gerätekopf
ausbauen)
So gehen Sie vor:
K, L
• Filterschaum herausnehmen und unter warmem
Wasser spülen oder ersetzen.
• Keramiksubstrat unter warmen Wasser ausspülen
oder ersetzen.
– Vor dem Erstgebrauch Keramiksubstrat aus dem
Plastikbeutel nehmen, unter warmen Wasser
ausspülen und lose in den Filterbehälter füllen.
Laufeinheit reinigen/ersetzen
Voraussetzung
• Der Gerätekopf ist abgenommen. (→ Gerätekopf
ausbauen)
So gehen Sie vor:
M
• Pumpendeckel nach unten abziehen.
• Laufeinheit ausbauen, reinigen oder ersetzen.
• Gerät in umgekehrter Reihenfolge zusammen-
bauen.
– Auf korrekten Sitz der beiden Gummilager ach-
ten.
– Darauf achten, dass der Entlüfterschlauch vor-
handen ist und nach oben zeigt, damit die Luft
entweichen kann.
Gerät wieder installieren
• Gerätekopf und Filtereinheit wieder zusammen-
bauen. (→ Gerätekopf einbauen)

Chat with your Oase FiltoSmart 60 manual using AI

Get instant AI answers from your Oase FiltoSmart 60 manual

Ask anything about the Oase FiltoSmart 60. Answers come from this manual, with the pages they are based on.

FiltoSmart 60 Maintenance Schedule

Regularly
Check water level and circulation

Regularly check the water level and circulation in the filter and in the aquarium to ensure proper operation.

As needed
Clean unit with clear water and soft brush

If necessary, clean the unit with clear water using a soft brush. Do not use cleaning agents or chemical solutions.

Show in the manual (page 10)
As needed
Rinse or replace foam filter

Remove the foam filter and rinse it in warm water or replace it if worn. Frequency depends on tank size and stocking.

Show in the manual (page 10)
As needed
Rinse or replace ceramic substrate

Rinse the ceramic substrate in warm water or replace it if worn. Frequency depends on tank size and stocking.

Show in the manual (page 10)
As needed
Clean or replace impeller unit

Remove the pump lid, take out the impeller unit, clean it, or replace it if worn. Ensure rubber bearings are seated correctly.

Show in the manual (page 10)
M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend FiltoSmart 60?

Yes No

Frequently Asked Questions

A

The Oase FiltoSmart 60 is recommended for aquariums with a maximum volume of 60 liters.

Is this answer helpful?

A

Yes, the device is suitable for both freshwater and saltwater operations within the specified temperature range.

Is this answer helpful?

A

Ensure the vent hose is present and pointing upwards when reassembling the unit head to allow air to escape properly.

Is this answer helpful?

A

Thoroughly rinse all filter materials like the ceramic substrate and foam with warm tap water to remove any soiling before installation.

Is this answer helpful?

A

Yes, the unit has an IPX8 protection rating and is waterproof up to a depth of 1 meter.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Compact size fits perfectly in small aquarium setups
  • Dual filtration chambers provide excellent mechanical and biological cleaning
  • IPX8 rating allows safe submersion up to 1 meter depth
  • Easy-to-clean head design simplifies routine maintenance tasks
VS

Disadvantages

  • Hose length is limited to 1 meter which may restrict placement options
  • Ceramic substrate must be rinsed well before first use to avoid cloudiness
  • Pump cannot operate if running dry, requiring careful monitoring
  • Holder for wall mounting is sold separately and not included
M: QW-35-FL

Product Specification

Type

External Filter

Suitability

Freshwater, Saltwater, Aquarium

Flow Rate

79.3 gal/h

Net Pump Head

2.3 ft

Aquarium Size

max. 15.9 gal

Filtration

1.3 qt Filter Volume, 0.74 qt Pre-filter Volume, 1x Pre-filter Insert, 1x Filter Foam (Cartridge), 1x Ceramic Substrate (Filter Rings)

Connections

8/12mm Hose Connections

Power Consumption

5W

Dimensions

5.9x6.5x3.5 in (WxHxD)

Weight

1.88 lbs

Features

Self-priming, Outlet Pipe, Diffuser, Intake Pipe, 1x 3.3 ft Hose, 4.9 ft Cable Length, Includes Inlet/Outlet Set

Manufacturer Warranty

Three Years

M: QW-35-FL

Product Description

Oase FiltoSmart 60 External Filter Review

The Oase FiltoSmart 60 is a versatile external canister filter designed specifically for smaller aquariums up to 60 liters. This unit combines mechanical and biological filtration into a compact design, making it an ideal choice for freshwater or saltwater setups in home environments. The system utilizes a two-chamber filtration process where water first passes through a ceramic substrate for biological cleaning before moving through a 20 ppi foam filter for mechanical debris removal.

Installation is straightforward, allowing the unit to sit beside the tank or be mounted on the outside wall using a separate holder. The package includes all necessary hoses, suction cups, and a connection set with a water distributor option. Before initial use, it is crucial to rinse all filter media thoroughly with warm water to remove manufacturing dust. The pump features an IPX8 protection rating, ensuring it remains safe even if submerged up to one meter deep during operation.

Maintenance involves periodic cleaning of the impeller unit and replacing worn foam filters or ceramic substrates. Users should ensure the vent hose is correctly positioned to prevent air locks, which can cause noise or reduced flow. Always disconnect power before reaching into the water to handle the unit safely. This filter offers a reliable solution for keeping small aquatic habitats clear and healthy without taking up excessive space.

Key Features

  • Compact design suitable for tanks up to 60 liters
  • Dual-stage filtration with ceramic and foam media
  • Safe operation with IPX8 waterproof rating
  • Easy access head design for quick maintenance

Important Notes

  • Do not let the pump run dry as this will destroy the motor.
  • Cut cables before disposal to render the unit unusable.
  • Use only original spare parts for optimal performance.
M: QW-35-FL

© Copyright 2026 Manual.ly