Manual.ly Logo

Benning VT 1 Manual

5.0 · 1 Ratings

PDF manual · 39 Pages

English

M: QW-35-FL
page

/ 39

Loading...
b2bd134465851f0824cfe2518403304ed976 page a
08/ 2020
BENNING VT 1
10
Earth (voltage to earth)
This symbol shows the orientation of the batteries for inserting them with correct polarity.
2. Devicedescription (figure A)
1
ProbetipwithLEDindication (red)
2
Grip limit
3
Clip
4
Batterycompartmentcover
3. Functional test
- Check the phase indicator and cable break detector for correct functioning immediately before and
after using it!
- Test the phase test for correct functioning with a familiar voltage source, e.g. a 230 V socket/5-pin
CEE socket.
- Please replace the batteries as soon as the red LED indication
1
or the acoustic signal are getting
weaker.
- Do not use the BENNING VT 1, if not all functions are working properly!
- The BENNING VT 1 has no circuit breaker and is always enabled. A special circuit with low current
consumption extends the battery lifetime and thus ensures that the device is ready for use.
4. Howtheindicatorworks
- The BENNING VT 1 phase indicator and cable break detector detects electric fields generated by
phase/external conductor voltages from 200 V to 1,000 V AC (45 Hz to 65 Hz) on.
- If an electric field is detected, the probe tip
1
lights up in red color and an acoustic signal is emit-
ted. The flashing frequency of the red probe tip
1
as well as the frequency of the acoustic signal
increase with the electric field or the voltage applied increasing as well.
- The BENNING VT 1 phase indicator and cable break detector can be used to determine the phase
(external conductor) of an AC voltage.
- The test does not require any current flow and no electrically conductive contact with the system
part, socket or insulated line.
- Please observe that the BENNING VT 1 only responds to sufficiently strong fields with a phase/
external conductor voltage from 200 V AC on.
If the BENNING VT 1 phase indicator and cable break detector does not react, the distance to the live
system part might be too large, the system part might be shielded or the insulation might be too thick.
5. Phase/externalconductortestofanACvoltage (figure B)
- Place the probe tip
1
onto the assumed phase (external conductor) of the system part.
- If the phase (external conductor) has been detected, this is confirmed by an acoustic signal and by
the probe tip
1
lighting up in red color.
Attention!
Please observe that even if the BENNING VT 1 does not indicate a phase (external conductor), a dan-
gerous voltage may be applied to the test object nevertheless. For determining the absence of voltage,
only use a two-pole voltage tester complying with the DIN EN 61243-3 (VDE 0682-401) standard, e.g.
a DUSPOL
®
voltage tester.

Chat with your Benning VT 1 manual using AI

Get instant AI answers from your Benning VT 1 manual

Ask anything about the Benning VT 1. Answers come from this manual, with the pages they are based on.

VT 1 Maintenance Schedule

Before and after each use
Perform functional check

Check the device for correct functioning immediately before and after every use using a known voltage source.

Show in the manual (page 10)
As needed
Replace batteries

Replace batteries when the red LED indication or acoustic signal becomes weak. Use two Micro LR03/AAA batteries.

Show in the manual (page 10)
Periodically / When dirty
Clean housing and battery compartment

Clean the exterior of the device with a clean dry cloth. Clean contamination in the battery area with a dry cloth.

Show in the manual (page 11)
During long-term storage
Remove batteries during storage

If the device is stored for a longer period of time, remove the batteries from the device to prevent damage.

Show in the manual (page 11)
M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend VT 1?

Yes No
0
User Pic

Kayleigh Altenwerth

7 months ago

Does the side-specific shutdown check function reliably?

0
User Pic

Manual.ly

6 months ago

Yes, the side-specific shutdown check feature is designed to work effectively. Users have confirmed that it accurately verifies the shutdown status on each side, ensuring proper operation and safety.

M: QW-35-FL
M: QW-35-FL

Frequently Asked Questions

A

No, the BENNING VT1 is designed exclusively for alternating current (AC). It detects electric fields generated by phase voltages starting from approximately 200 V AC. Direct voltage (DC) fields will not be recognized by this device.

Is this answer helpful?

A

You should replace the batteries immediately if the red LED indicator becomes dim or if the acoustic signal becomes weak. A functional check on a known voltage source is recommended before every use to ensure reliability.

Is this answer helpful?

A

Yes, provided you follow all safety instructions. The device is rated for CAT III 1000 V and CAT IV 600 V environments. However, it must only be used by qualified electricians, and you must never touch the white probe tip while testing.

Is this answer helpful?

A

No, you cannot use the BENNING VT1 to confirm the absence of voltage. It only indicates the presence of a phase. To determine if a circuit is de-energized, you must use a certified two-pole voltage tester compliant with DIN EN 61243-3.

Is this answer helpful?

A

The BENNING VT1 requires two Micro batteries, specifically type LR03 or AAA (1.5 V). They must be inserted with the correct polarity, positive pole facing forward, into the battery compartment.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Non-contact operation ensures high safety for the user by preventing direct contact with live parts.
  • Dual indication system with both visual LED and audible tone provides clear confirmation of phase presence.
  • Capable of detecting cable breaks and interruptions in live lines without cutting insulation.
  • Always active design with low current consumption extends battery life and readiness for use.
  • Robust construction meets CAT III 1000V and CAT IV 600V overvoltage categories for professional environments.
VS

Disadvantages

  • Cannot verify the absence of voltage; a separate two-pole tester is required for safety verification.
  • Does not detect direct current (DC) voltages, limiting its use to AC systems only.
  • Performance can be affected by excessive distance, thick insulation, or heavy shielding around conductors.
  • Requires frequent battery replacement when signals weaken, as there is no power switch to turn off.
  • Not suitable for unqualified personnel; strictly intended for use by trained electricians.
M: QW-35-FL

Product Specification

Measurement range

200-1000V

M: QW-35-FL

Product Description

Benning VT1 Non-contact Phase Tester - Read, Download & Print Free

The Benning VT1 Non-contact Phase Tester is an essential tool for qualified electricians who need to quickly and safely identify live phases in electrical installations. Designed with a focus on user safety and reliability, this device allows professionals to detect alternating voltage fields without making direct physical contact with the conductor. This feature significantly reduces the risk of accidental short circuits or electric shocks during routine checks.

Operating within a nominal voltage range of 200 V to 1,000 V AC, the BENNING VT1 responds to frequencies between 45 Hz and 65 Hz. When an electric field is detected, the device provides immediate feedback through a bright red LED located at the probe tip and an audible acoustic signal. The intensity of both the light and sound increases as the voltage strength rises, giving the operator a clear indication of the presence and magnitude of the phase voltage.

Beyond simple phase detection, the Benning VT1 serves as a cable break detector. By sliding the probe along an insulated line from the power source towards the end, users can locate interruptions such as broken wires in cable reels or defective bulbs in lighting chains. The moment the signal stops, the exact location of the break has been found. It is important to note that this device does not confirm the absence of voltage; it only indicates presence. For verifying that a circuit is truly dead, a two-pole voltage tester must be used.

Safety is paramount in the design of this instrument. It features a protective insulation class II construction and includes a grip limit to ensure hands never touch the sensitive white probe tip during operation. The unit is always active, utilizing a special low-power circuit to maximize battery life, though it requires fresh AAA batteries to function correctly. With its compact dimensions and lightweight build, it fits easily into any toolkit while meeting rigorous industrial standards like DIN EN 61010-1.

Important Notes

  • Always perform a functional test on a known live source before and after using the device.
  • Do not use the tester if the battery compartment is open or if indicators are weak.
  • The device cannot detect DC voltage fields.
  • Ensure proper distance from the conductor; thick insulation or shielding may prevent detection.
M: QW-35-FL

© Copyright 2026 Manual.ly