Manual.ly Logo

Worx WX531 Manual

0.0 · 0 Ratings

PDF manual · 176 Pages

English

M: QW-35-FL
page

/ 176

Loading...
2e5fadf0654c313c12b976fa9ea14bd502cc page c
EN20V Cordless Brushless Circular saw
12
the least amount of wheel is exposed
towards the operator. Position yourself
and bystanders away from the plane
of the rotating wheel. The guard helps to
protect operator from broken wheel fragments
and accidental contact with wheel.
b) Use only bonded reinforced or diamond
cut-off wheels for your power tool. Just
because an accessory can be attached to your
power tool, it does not assure safe operation.
c) The rated speed of the accessory must
be at least equal to the maximum speed
marked on the power tool. Accessories
running faster than their rated speed can break
and fly apart.
d) Wheels must be used only for
recommended applications. For example:
do not grind with the side of cut-off
wheel. Abrasive cut-off wheels are intended
for peripheral grinding, side forces applied to
these wheels may cause them to shatter.
e) Always use undamaged wheel flanges
that are of correct diameter for your
selected wheel. Proper wheel flanges
support the wheel thus reducing the possibility
of wheel breakage.
f) Do not use worn down reinforced wheels
from larger power tools. Wheels intended
for a larger power tool are not suitable for the
higher speed of a smaller tool and may burst.
g) The outside diameter and the thickness
of your accessory must be within the
capacity rating of your power tool.
Incorrectly sized accessories cannot be
adequately guarded or controlled.
h) The arbour size of wheels and flanges
must properly fit the spindle of the power
tool. Wheels and flanges with arbour holes
that do not match the mounting hardware of
the power tool will run out of balance, vibrate
excessively and may cause loss of control.
i) Do not use damaged wheels. Before
each use, inspect the wheels for chips
and cracks. If power tool or wheel is
dropped, inspect for damage or install an
undamaged wheel. After inspecting and
installing the wheel, position yourself
and bystanders away from the plane of
the rotating wheel and run the power
tool at maximum no load speed for one
minute. Damaged wheels will normally break
apart during this test time.
j) Wear personal protective equipment.
Depending on application, use face
shield, safety goggles or safety glasses.
As appropriate, wear dust mask, hearing
protectors, gloves and shop apron
capable of stopping small abrasive or
workpiece fragments. The eye protection
must be capable of stopping flying debris
generated by various operations. The dust
mask or respirator must be capable of filtrating
particles generated by your operation.
Prolonged exposure to high intensity noise
may cause hearing loss.
k) Keep bystanders a safe distance away
from work area. Anyone entering the
work area must wear personal protective
equipment. Fragments of workpiece or of a
broken wheel may fly away and cause injury
beyond immediate area of operation.
l) Hold the power tool by insulated gripping
surfaces only, when performing an
operation where the cutting accessory
may contact hidden wiring. Cutting
accessory contacting a “live” wire may make
exposed metal parts of the power tool “live”
and could give the operator an electric shock.
m) Never lay the power tool down until the
accessory has come to a complete stop.
The spinning wheel may grab the surface and
pull the power tool out of your control.
n) Do not run the power tool while carrying
it at your side. Accidental contact with the
spinning accessory could snag your clothing,
pulling the accessory into your body.
o) Regularly clean the power tool’s air
vents. The motor’s fan will draw the dust
inside the housing and excessive accumulation
of powdered metal may cause electrical
hazards.
p) Do not operate the power tool near
flammable materials. Sparks could ignite
these materials.
KICKBACK AND RELATED
WARNINGS
Kickback is a sudden reaction to a pinched or
snagged rotating wheel. Pinching or snagging
causes rapid stalling of the rotating wheel which
in turn causes the uncontrolled power tool to be
forced in the direction opposite of the wheel’s
rotation at the point of the binding.
For example, if an abrasive wheel is snagged or
pinched by the workpiece, the edge of the wheel
that is entering into the pinch point can dig into
the surface of the material causing the wheel to
climb out or kick out. The wheel may either jump
toward or away from the operator, depending on
direction of the wheel’s movement at the point of
pinching. Abrasive wheels may also break under
these conditions.
Kickback is the result of power tool misuse and/or
incorrect operating procedures or conditions and
can be avoided by taking proper precautions as
given below.
a) Maintain a firm grip on the power tool
and position your body and arm to allow
you to resist kickback forces. Always
use auxiliary handle, if provided, for
maximum control over kickback or torque
reaction during start-up. The operator can
control torque reactions or kickback forces, if
proper precautions are taken.
b) Never place your hand near the rotating
accessory. Accessory may kickback over your
hand.

Chat with your Worx WX531 manual using AI

Get instant AI answers from your Worx WX531 manual

Ask anything about the Worx WX531. Answers come from this manual, with the pages they are based on.

WX531 Maintenance Schedule

Before each use
Check lower guard for proper closing and free movement

Ensure the lower guard moves freely and closes instantly. Do not operate if it does not close or is bent.

Show in the manual (page 11)
Before each use
Inspect saw blades for damage

Check for chips, cracks, dullness, or damage. Replace if necessary to prevent kickback and ensure safety.

Show in the manual (page 12)
Regularly
Clean air vents of dust accumulation

Remove dust from motor ventilation slots to prevent electrical hazards caused by excessive metal powder buildup.

Show in the manual (page 18)
Periodically
Clear dust and chips from guard and base plate

Remove accumulated sawdust and debris from the blade guard and base to ensure proper performance and operation.

Show in the manual (page 18)
As needed
Keep cutting tools sharp and clean

Maintain sharp edges on blades to reduce binding and improve control. Use only recommended sharp blades.

Show in the manual (page 10)
M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend WX531?

Yes No

Frequently Asked Questions

A

The saw accepts 115mm diameter blades with a 9.5mm arbor hole. It supports TCT blades for wood, HCS blades for softer materials, and abrasive diamond discs for tiles and masonry.

Is this answer helpful?

A

No, the battery and charger are not included in the standard package. You must purchase them separately or use an existing Worx 20V PowerShare battery if you own other compatible tools.

Is this answer helpful?

A

Yes, by swapping the standard wood blade for the appropriate accessory. Use an abrasive diamond disc for cutting tiles and metal, ensuring the rated speed matches the tool's 6900 RPM.

Is this answer helpful?

A

The maximum cutting depth at 90 degrees is 41mm. At a 45-degree bevel angle, the depth reduces to 29.5mm, allowing for versatile joinery and structural cuts.

Is this answer helpful?

A

Yes, the Worx WX531 features a dedicated dust extraction outlet. You can connect it to a shop vacuum using the included adapter to keep the work area clean and improve visibility.

Is this answer helpful?

A

The machine weighs 1.71kg as a bare tool. Adding a battery will increase the total weight depending on the capacity of the 20V PowerShare pack used.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Brushless motor delivers high speed and long life
  • Compatible with all Worx 20V PowerShare batteries
  • Lightweight at 1.71kg for easy handling
  • Automatic pendulum guard enhances user safety
  • Includes parallel guide for accurate straight cuts
VS

Disadvantages

  • Battery and charger sold separately
  • Dust collection requires external vacuum attachment
  • Blade size limited to 115mm diameter
  • No onboard storage for hex key or wrench
  • Bevel adjustment range stops at 46 degrees
M: QW-35-FL

Product Specification

Type

Circular saw

No-load speed

6900 rpm

Blade diameter

4.53 in

Cutting capacity

1.61 in (cut depth at 0°), 1.16 in (cut depth at 45° tilt)

Bevel range

0-46°

Arbor

3/8 in bore, spindle lock

Features

Fence, dust extraction, bevel function

Weight

3.77 lb (without battery)

M: QW-35-FL

Product Description

Worx WX531 20V PowerShare Hand Circular Saw: Precision and Power in Your Hands

The Worx WX531 20V PowerShare Hand Circular Saw represents a significant leap in portable woodworking tools, designed for both professional contractors and serious DIY enthusiasts. This cordless powerhouse eliminates the constraints of cords while delivering robust performance through its brushless motor technology. The integration with the Worx PowerShare system allows users to utilize compatible batteries across a wide range of tools, ensuring maximum versatility and convenience on any job site.

Equipped with a high-speed brushless motor, this saw achieves an impressive no-load speed of 6900 RPM. This power translates into clean, efficient cuts through wood, metal, aluminum, and even tiles when paired with the appropriate blade. The machine features a cutting depth of 41mm at 90 degrees and 29.5mm at a 45-degree bevel, providing ample capability for most framing and finishing tasks. Its lightweight design, weighing only 1.71kg without the battery, ensures reduced operator fatigue during extended use.

Safety is paramount in the design of the WX531. It includes a pendulum lower guard that automatically retracts during operation and snaps back instantly to cover the blade when released. The tool also features a safety switch and an on/off trigger to prevent accidental starts. A parallel guide is included to ensure straight, accurate rip cuts, while adjustable depth and angle levers allow for precise customization. Dust extraction capabilities are integrated via a vacuum adapter, helping to maintain a cleaner workspace and improve visibility.

Whether you are building a deck, framing a wall, or cutting ceramic tiles, the Worx WX531 offers the reliability and control needed for professional results. Its compatibility with various 20V batteries means you can choose the capacity that suits your specific project duration, from 1.5Ah packs for light duty to 4.0Ah units for heavy-duty applications. This saw stands as a testament to modern engineering, combining safety, efficiency, and portability into one compact unit.

M: QW-35-FL

© Copyright 2026 Manual.ly