Manual.ly Logo

Worx WX529.9 Manual

0.0 · 0 Ratings

PDF manual · 96 Pages

English

M: QW-35-FL
page

/ 96

Loading...
e5ea7af1a1ad046e8db3a116ef39fccd7efd page 8
Lithium-Ion cordless circular saw
EN
8
that saw teeth are not engaged into the
material. If saw blade is binding, it may walk
up or kickback from the workpiece as the saw is
restarted.
d) Support large panels to minimize the risk of
blade pinching and kickback. Large panels
tend to sag under their own weight. Supports
must be placed under the panel on both sides,
near the line of cut and near the edge of the
panel.
e) Do not use dull or damaged blades.
Unsharpened or improperly set blades produce
narrow kerf causing excessive friction, blade
binding and kickback.
f) Blade depth and bevel adjusting locking
levers must be tight and secure before
making cut. If blade adjustment shifts while
cutting, it may cause binding and kickback.
g) Use extra caution when sawing into
existing walls or other blind areas. The
protruding blade may cut objects that can cause
kickback.
SAFETY INSTRUCTIONS
FOR CIRCULAR SAW WITH
INNER PENDULUM GUARD
a) Check lower guard for proper closing
before each use. Do not operate the saw
if lower guard does not move freely and
close instantly. Never clamp or tie the
lower guard into the open position. If saw is
accidentally dropped, lower guard may be bent.
Raise the lower guard with the retracting handle
and make sure it moves freely and does not touch
the blade or any other part, in all angles and
depths of cut.
b) Check the operation of the lower guard
spring. If the guard and the spring are
not operating properly, they must be
serviced before use. Lower guard may operate
sluggishly due to damaged parts, gummy
deposits, or a build-up of debris.
c) Lower guard may be retracted manually
only for special cuts such as “plunge cuts”
and “compound cuts.” Raise lower guard
by retracting handle and as soon as blade
enters the material, the lower guard must
be released. For all other sawing, the lower
guard should operate automatically.
d) Always observe that the lower guard is
covering the blade before placing saw
down on bench or floor. An unprotected,
coasting blade will cause the saw to walk
backwards, cutting whatever is in its path. Be
aware of the time it takes for the blade to stop
after switch is released.
ADDITIONAL SAFETY
RULES FOR YOUR
CIRCULAR SAW
1. Always wear a dust mask, hearing protection and
eye protection.
2. Only use saw blades recommended in the
specification.
3. Do not use any abrasive wheels.
4. Use only blade diameter(s) in accordance with
the markings.
SAFETY INSTRUCTIONS
FOR BATTERY PACK
a) Do not dismantle, open or shred cells or
battery pack.
b) Do not short-circuit a battery pack. Do not
store battery packs haphazardly in a box or
drawer where they may short-circuit each
other or be short-circuited by conductive
materials. When battery pack is not in use, keep
it away from other metal objects, like paper
clips, coins, keys, nails, screws or other small
metal objects, that can make a connection from
one terminal to another. Shorting the battery
terminals together may cause burns or a fire.
c) Do not expose battery pack to heat or fire.
Avoid storage in direct sunlight.
d) Do not subject battery pack to mechanical
shock.
e) In the event of battery leaking, do not
allow the liquid to come into contact
with the skin or eyes. If contact has been
made, wash the affected area with copious
amounts of water and seek medical advice.
f) Seek medical advice immediately if a cell or
battery pack has been swallowed.
g) Keep battery pack clean and dry.
h) Wipe the battery pack terminals with a
clean dry cloth if they become dirty.
i) Battery pack needs to be charged before
use. Always refer to this instruction and
use the correct charging procedure.
j) Do not maintain battery pack on charge
when not in use.
k) After extended periods of storage, it may
be necessary to charge and discharge
the battery pack several times to obtain
maximum performance.
l) Battery pack gives its best performance
when it is operated at normal room
temperature (20°C ± 5°C).
m) When disposing of battery packs, keep
battery packs of different electrochemical
systems separate from each other.
n) Recharge only with the charger specified
by WORX. Do not use any charger other
than that specifically provided for use with
the equipment. A charger that is suitable for

Chat with your Worx WX529.9 manual using AI

Get instant AI answers from your Worx WX529.9 manual

Ask anything about the Worx WX529.9. Answers come from this manual, with the pages they are based on.

WX529.9 Maintenance Schedule

Before each use
Check lower guard for proper closing

Ensure the lower guard moves freely and closes instantly. Do not operate if it does not close automatically or is damaged.

Periodically
Inspect tool cords

Check power cords regularly for damage. If damaged, have them repaired by an authorized service facility to avoid hazards.

Show in the manual (page 10)
Periodically
Clear dust and chips from guard and base

Remove accumulated sawdust and debris from the blade guard and base plate to ensure proper performance of the saw.

Show in the manual (page 10)
As needed
Wipe battery terminals with a clean dry cloth

Clean the battery pack terminals if they become dirty to maintain good electrical contact and prevent issues.

M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend WX529.9?

Yes No

Frequently Asked Questions

A

The solo package includes the circular saw unit, a TCT blade, a dust adapter, and a hex key. It does not include a battery or charger, which must be purchased separately.

Is this answer helpful?

A

Yes, this saw is part of the Worx PowerShare system. You can use any Worx 20V Max Li-ion battery pack that fits the tool's battery slot.

Is this answer helpful?

A

Always remove the battery pack first. Press the spindle lock button to hold the shaft, then use the hex key to loosen the blade bolt. Replace the blade ensuring the flanges are tight before reinserting the battery.

Is this answer helpful?

A

The maximum cutting depth at a 90-degree angle is 45mm. At a 45-degree bevel angle, the maximum depth is reduced to 33mm.

Is this answer helpful?

A

No, the standard kit does not include a rip fence. You will need to purchase one separately or use a straight edge guide for accurate ripping cuts.

Is this answer helpful?

A

You should periodically clear dust and chips from the guard and base plate to ensure proper performance and prevent binding during operation.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Compatible with all Worx 20V PowerShare batteries for maximum versatility
  • Lightweight design at 2.37kg reduces operator fatigue during long tasks
  • Bevel capacity ranges from 0 to 50 degrees for complex angled cuts
  • Includes a dust adapter for improved workspace cleanliness
  • No-load speed of 3600 RPM ensures fast and efficient cutting performance
VS

Disadvantages

  • Solo kit excludes battery and charger requiring separate purchase
  • Maximum cutting depth limited to 45mm which may restrict thick material work
  • Vibration levels require anti-vibration accessories for prolonged use
  • Dust collection is optional and requires a separate vacuum attachment
  • Blade size is fixed at 150mm limiting options for larger diameter blades
M: QW-35-FL

Product Specification

Type

Hand circular saw

Battery

20V, Li-ion

No-load speed

3600 rpm

Blade diameter

5.91 in

Cutting capacity

1.77 in (cut depth at 0°), 1.18 in (cut depth at 45° tilt)

Bevel angle

0-50°

Arbor

16mm hole, spindle lock

Features

Soft grip, auxiliary handle, dust extraction, bevel function

Weight

5.23 lbs

Package contents

without charger and battery

M: QW-35-FL

Product Description

Worx WX529.9 20V PowerShare Cordless Circular Saw Solo Manual Review

The Worx WX529.9 20V PowerShare Cordless Circular Saw Solo is a versatile tool designed for DIY enthusiasts and professional woodworkers who demand precision without the tether of a power cord. This saw operates on the Worx PowerShare system, allowing users to utilize compatible 20V batteries from across the Worx lineup, offering exceptional flexibility for various projects around the home or job site.

At the heart of this machine is a powerful motor capable of reaching a no-load speed of 3600 RPM. It features a 150mm TCT blade that ensures clean cuts through wood, plastic, and other soft materials. The base plate allows for bevel adjustments ranging from 0 to 50 degrees, enabling angled cuts with ease. A depth adjustment scale helps users set precise cutting depths up to 45mm at 90 degrees and 33mm at 45 degrees. The inclusion of a dust adapter makes it easier to maintain a cleaner workspace by connecting to a vacuum system.

Safety is a top priority with the WX529.9. It includes a lower guard lever that automatically retracts during cutting and covers the blade when not in use. An on/off switch with a lock-off button prevents accidental activation. The ergonomic front handle provides better control, while the spindle lock button simplifies blade changes. Users should always wear appropriate safety gear, including eye protection, hearing protection, and a dust mask, as per the manual instructions.

This solo kit does not include a battery or charger, focusing solely on the tool itself. However, its lightweight design at approximately 2.37kg (without battery) reduces user fatigue during extended use. Whether you are ripping lumber or making cross-cuts, this saw delivers reliable performance when paired with a fully charged Worx 20V battery.

Important Notes

  • Always remove the battery before changing blades or performing maintenance.
  • Ensure the lower guard moves freely before each use.
  • Use only recommended TCT blades for optimal safety and cut quality.
M: QW-35-FL

© Copyright 2026 Manual.ly