Manual.ly Logo

Worx WX527 Manual

0.0 · 0 Ratings

PDF manual · 132 Pages

English

M: QW-35-FL
page

/ 132

Loading...
e707d5cf4be3fb0a1b308d59463d079fb2be page d
Lithium-Ion Cordless Circular Saw
EN
13
OPERATING INSTRUCTIONS
NOTE: Before using the tool, read the
instruction book carefully.
INTENDED USE:
The tool is intended for ripping and cross-cutting
wood and other materials in straight cutting lines,
while resting firmly on the work piece.
ASSEMBLY AND OPERATION
Action Figure
BEFORE OPERATION
Removing the battery pack See Fig. A1
Charging the battery See Fig. A2
Installing the battery pack See Fig. A3
ASSEMBLY
Saw blade Assembly and
Removing
WARNING: Always
remove the battery
before changing the blade!
See Fig. B
Safety On/Off Switch
WARNING:
To avoid
cutting injury from the
sharp blade, please don’t put
your hands around the Base
Plate.
See Fig. C1, C2
Cross and Rip Cutting
Note: To avoid injury from
Kickback, please don’t start
cutting until the blade runs
stably.
See Fig. D1, D2
Cutting Depth Adjusting See Fig. E1, E2
Parallel Guide See Fig. F
Pocket Cutting See Fig. G1, G2
Sawdust Removal See Fig. H
WORKING HINTS FOR YOUR
TOOL
If your power tool becomes too hot, please run your
circular saw no load for 2-3 minutes to cool the motor.
Avoid prolonged usage at very low speeds.
Protect saw blades against impact and shock. Cutting
with extreme force can significantly reduces the
performance capability of the tool and reduces the
service life of the saw blade. Sawing performance and
cutting quality depend essentially on the condition
and the tooth count of the saw blade. Therefore, use
only sharp saw blades that are suited for the material
being cut.
Choice of blades: 24 teeth for general work, approx. 40
teeth for finer cuts, more than 40 teeth for very fine cuts
into delicate surfaces, diamond for tile, cement board,
etc.
Only use saw blades recommended.
MAINTENANCE
Remove the battery pack from the tool before
carrying out any adjustment, servicing or
maintenance.
Keep tools sharp and clean for better and safer
performance. Follow instructions for lubricating and
changing accessories. Inspect tool cords periodically and
if damaged, have repaired by authorized service facility.
Your power tool requires no additional lubrication or
maintenance. There are no user serviceable parts in
your power tool. Never use water or chemical cleaners
to clean your power tool. Wipe clean with a dry cloth.
Always store your power tool in a dry place. Keep the
motor ventilation slots clean. Keep all working controls
free of dust.
If the supply cord is damaged, it must be replaced by
the manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
Periodically clear dust and chips from guard and base to
ensure proper performance.
For Battery tools
The ambient temperature range for the use and storage
of tool and battery is 0
o
C-45
o
C.
The recommended ambient temperature range for the
charging system during charging is 0
o
C-40
o
C.
ENVIRONMENTAL
PROTECTION
Waste electrical products must not be disposed
of with household waste. Please recycle where
facilities exist. Check with your local authorities
or retailer for recycling advice.

Chat with your Worx WX527 manual using AI

Get instant AI answers from your Worx WX527 manual

Ask anything about the Worx WX527. Answers come from this manual, with the pages they are based on.

WX527 Maintenance Schedule

Before each use
Check guard closing and movement

Verify the lower guard closes properly and moves freely before every use. Do not operate if it does not enclose the blade instantly.

Periodically
Inspect power cord for damage

Inspect tool cords periodically. If damaged, have repaired by authorized service facility to avoid electric shock hazard.

Show in the manual (page 13)
Periodically
Clear dust from guard and base

Remove accumulated dust and chips from the guard and base plate regularly to ensure proper performance of the saw.

Show in the manual (page 13)
As needed
Wipe battery terminals

If battery pack terminals become dirty, wipe them with a clean dry cloth to maintain good electrical contact.

M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend WX527?

Yes No

Frequently Asked Questions

A

The Worx WX527 uses the Worx PowerShare 20V Lithium-Ion battery system. It is compatible with all batteries in the Worx 20V lineup, allowing you to use interchangeable power sources from drills, lights, and other tools.

Is this answer helpful?

A

Yes, the Worx WX527 can cut metal if you install the appropriate HSS blade. However, it is primarily designed for wood. When cutting metal, ensure the blade is sharp and rated for the specific metal type to avoid binding or kickback.

Is this answer helpful?

A

First, remove the battery pack for safety. Press the spindle lock button to hold the blade stationary. Use the included hex key to loosen the blade bolt, remove the outer flange, replace the blade, and then reassemble the flange and bolt securely before reinstalling the battery.

Is this answer helpful?

A

In many standard kits, the Worx WX527 is sold as a bare tool without a battery or charger. You must purchase these separately unless specified as part of a combo kit. Check the product listing carefully to confirm what is included in the box.

Is this answer helpful?

A

The maximum cutting depth of the Worx WX527 is 27mm. This depth is sufficient for most residential woodworking projects involving lumber and plywood, but it may be insufficient for very thick timbers or heavy-duty construction beams.

Is this answer helpful?

A

Yes, the saw features a vacuum adapter and a dust extraction outlet. You can connect a shop vacuum to collect sawdust directly from the source, helping to keep your work area clean and improving visibility while cutting.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Compatible with all Worx 20V PowerShare batteries for maximum flexibility
  • Includes a vacuum adapter for effective dust extraction and cleaner workspaces
  • Soft grip handle provides enhanced comfort and control during operation
  • Compact and lightweight design makes it easy to maneuver for detailed cuts
  • Integrated parallel guide ensures accurate and straight ripping cuts
VS

Disadvantages

  • Maximum cutting depth is limited to 27mm which may restrict thicker material work
  • Battery and charger are sold separately in some configurations requiring additional investment
  • Blade size is smaller than standard 184mm saws limiting cut width on large panels
  • May experience reduced power when using older or depleted battery packs
  • Noise level of 92dB requires ear protection for prolonged usage periods
M: QW-35-FL

Product Specification

Type

Circular saw

No-load speed

2500 rpm

Blade diameter

3.35 in

Cutting capacity

1.06 in (cutting depth at 0 degrees)

Tool holder

Bore 0.59 in, spindle lock

Features

Soft grip, guide fence, dust extraction

Weight

3.20 lbs

M: QW-35-FL

Product Description

Worx WX527 20V PowerShare Cordless Hand Circular Saw Review

The Worx WX527 is a versatile Lithium-Ion cordless circular saw designed for precision cutting in wood and other materials. This tool features a compact design with a soft grip handle that ensures comfort during extended use. The saw operates at a no-load speed of 2500 RPM, allowing it to slice through wood up to 27mm thick with ease. Its 85mm TCT blade is optimized for general work, delivering clean cuts across various project types.

One of the standout features of the WX527 is its compatibility with the Worx PowerShare system. Users can utilize any 20V battery from the Worx lineup, providing flexibility and convenience for professionals and DIY enthusiasts alike. The inclusion of a vacuum adapter allows for dust extraction, keeping your workspace cleaner and reducing health hazards associated with sawdust inhalation. The parallel guide ensures straight cuts, making it ideal for ripping tasks where accuracy is paramount.

Safety is a top priority with this model. It includes an upper fixed guard and a lower retractable guard that automatically covers the blade when not cutting. The tool also features a spindle lock for easy blade changes and a safety switch to prevent accidental activation. Proper maintenance involves keeping the base plate free of debris and ensuring the blade remains sharp for optimal performance.

Important Notes

  • Always remove the battery before changing blades or performing maintenance.
  • Use only recommended blades to prevent kickback and ensure safety.
  • Store the tool in a dry place to protect the motor and electronics.
M: QW-35-FL

© Copyright 2026 Manual.ly