Manual.ly Logo

Worx WX445 Manual

0.0 · 0 Ratings

PDF manual · 144 Pages

English

M: QW-35-FL
page

/ 144

Loading...
8d4ea7e1d2824b596f3713c0e045fd246045 page a
Circular saw with laser EN
10
- If the blade becomes twisted or misalign
in the cut, the teeth at the back edge of the
blade can dig into the top surface of the
wood causing the blade to climb out of the
kerf and jump back toward the operator.
KICKBACK IS THE RESULT OF SAW
MISUSE AND/OR INCORRECT
OPERATING PROCEDURES OR
CONDITIONS AND CAN BE AVOIDED BY
TAKING PROPER PRECAUTIONS AS
GIVEN BELOW.
a. Maintain a firm grip with both hands
on the saw and position your arms to
resist kickback forces. Position your
body to either side of the blade, but
not in line with the blade. Kickback
could cause the saw to jump backwards,
but kickback forces can be controlled by the
operator, if proper precautions are taken.
b. When blade is binding, or when
interrupting a cut for any reason,
release the trigger and hold the
saw motionless in the material until
the blade comes to a complete
stop. Never attempt to remove the
saw from the work or pull the saw
backward while the blade is in motion
or kickback may occur. Investigate and
take corrective actions to eliminate the
cause of blade binding.
c. When restarting a saw in the work-
piece, center the saw blade in the
kerf and check that saw teeth are not
engaged into the material. If saw blade
is binding, it may walk up or kickback from
the work-piece as the saw is restarted.
d. Support large panels to minimize the
risk of blade pinching and kickback.
Large panels tend to sag under their own
weight. Supports must be placed under
the panel on both sides, near the line of cut
and near the edge of the panel.
e. Do not use dull or damaged blades.
Unsharpened or improperly set blades
product narrow kerf causing excessive
friction, blade binding and kickback.
f. Blade depth and bevel adjusting
locking levers must be tight and
secure before making cut. If blade
adjustment shifts while cutting, it may
cause binding and kickback.
g. Use extra caution when making a
“plunge cut” into existing walls or
other blind areas. The protruding blade
may cut objects that can cause kickback.
SAFETY INSTRUCTION
FOR CIRCULAR SAW WITH
INNER PENDULUM GUARD
a. Check lower guard for proper closing
before each use. Do not operate the
saw if lower guard does not move
freely and close instantly. Never
clamp or tie the lower guard into the
open position. If saw is accidentally
dropped, lower guard may be bent. Raise
the lower guard with the retracting handle
and make sure it moves freely and does
not touch the blade or any other parts, in all
angles and depths of cut.
b. Check the operation of the lower
guard spring. If the guard and the
spring are not operating properly,
they must be serviced before use.
Lower guard may operate sluggishly due
to damaged parts, gummy deposits, or a
build-up of debris.
c. Lower guard should be retracted
manually only for special cuts such
as “plunge cuts” and “compound
cuts”. Raise lower guard by retracting
handle and as soon as blade enters
the material, the lower guard must be
released. For all other sawing, the lower
guard should operate automatically.
d. Always observe that the lower guard
is covering the blade before placing
saw down on bench or floor. An
unprotected, coasting blade will cause the
saw to walk backwards, cutting whatever is
in its path. Be aware of the time it takes for
blade to stop after switch is released.

Chat with your Worx WX445 manual using AI

Get instant AI answers from your Worx WX445 manual

Ask anything about the Worx WX445. Answers come from this manual, with the pages they are based on.

WX445 Maintenance Schedule

Before each use
Check lower guard for proper closing

Ensure the lower guard moves freely and closes instantly. Do not operate if it does not close properly.

Show in the manual (page 10)
Regularly
Clean the vacuum adapter

Clean the dust extraction adapter regularly to ensure optimum dust extraction performance.

Show in the manual (page 13)
Periodically
Clean the laser generator

Clean the laser generator periodically to maintain visibility of the guide line.

Show in the manual (page 13)
As needed
Keep motor ventilation slots clean

Wipe the tool with a dry cloth and keep motor ventilation slots free of dust and debris.

Show in the manual (page 13)
M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend WX445?

Yes No

Frequently Asked Questions

A

The Worx WX445 can cut up to 66mm deep at a 90-degree angle. For the WX445.1 model, the maximum depth is 64mm.

Is this answer helpful?

A

Locate the plastic access caps on the front or back of the motor housing. Remove them with a flathead screwdriver, take out the old brushes, insert new ones fully, and secure the caps back in place.

Is this answer helpful?

A

No, this saw is designed exclusively for wood cutting. Using metal or stone blades can cause damage and is unsafe.

Is this answer helpful?

A

Yes, staring directly into the Class 2 laser beam can cause flash blindness. Never aim it at people or reflective surfaces.

Is this answer helpful?

A

You must inspect the lower guard before every use to ensure it closes instantly and moves freely without obstruction.

Is this answer helpful?

A

The saw operates on a rated voltage of 220-240V at 50/60Hz.

Is this answer helpful?

A

Standard delivery includes the saw, blade, parallel guide, hex key, and vacuum adapter, but not a carrying case.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Integrated laser guide ensures highly accurate cuts
  • Powerful 1600W motor handles tough wood efficiently
  • Ergonomic dual-handle design offers superior control
  • Vacuum adapter supports effective dust extraction
  • Adjustable base plate allows bevel cuts up to 51 degrees
VS

Disadvantages

  • Laser battery may require frequent replacement over time
  • Heavy vibration levels may cause fatigue during prolonged use
  • No built-in LED light for dark work areas
  • Blade size varies slightly between WX445 and WX445.1 models
  • Requires external vacuum hose for optimal dust collection
M: QW-35-FL

Product Specification

Type

Circular saw

Power

1600 W

No-load speed

5000 rpm

Blade diameter

7.48 in

Cutting capacity

2.60 in (cutting depth at 0°), 1.85 in (cutting depth at 45° tilt)

Bevel angle

0-51°

Arbor size

1.18 in

Features

Softgrip, auxiliary handle, guide fence, dust extraction, cutting line laser, bevel function

Weight

9.48 lbs

M: QW-35-FL

Product Description

Worx WX445 Electric Hand Circular Saw - Precision and Power

The Worx WX445 Electric Hand Circular Saw is a robust tool designed for woodworkers who demand accuracy and efficiency. This powerful saw features a 1600-watt motor that delivers a no-load speed of 5000 RPM, ensuring clean cuts through various wood materials. Whether you are tackling long straight cuts or complex bevel angles up to 51 degrees, this saw handles the job with ease.

One of the standout features of the Worx WX445 is its integrated laser guide. This device projects a precise line onto the workpiece, aligning perfectly with the blade path. This visual aid significantly reduces errors and helps users achieve professional-grade results without the need for extensive measuring during every cut. The saw also includes a parallel guide, allowing for consistent rip cuts at set distances from the edge of the material.

Safety is paramount in the design of this tool. It comes equipped with a lower pendulum guard that automatically retracts when cutting begins and covers the blade immediately after. The lock-off button prevents accidental starts, while the spindle lock allows for safe and easy blade changes. Users can adjust the cutting depth easily using the dedicated lever and scale, ensuring only the necessary amount of blade protrudes below the workpiece to minimize kickback risks.

For cleaner workspaces, the Worx WX445 includes a vacuum adapter compatible with dust extraction systems. This feature helps keep the cutting area clear of sawdust, improving visibility and reducing health hazards associated with airborne particles. The ergonomic rear handle and front grip provide excellent control, even during extended use, though users should always wear appropriate eye, ear, and respiratory protection as recommended by safety standards.

Key Notes

  • Always ensure the blade is sharp and suitable for the material being cut.
  • Check that the lower guard moves freely before each operation.
  • Never remove the safety guards or modify the tool's safety mechanisms.
  • Use genuine replacement parts for maintenance tasks like brush replacement.
M: QW-35-FL

© Copyright 2026 Manual.ly