Manual.ly Logo

Worx WG368E.9 Manual

0.0 · 0 Ratings

PDF manual · 204 Pages

English

M: OA-GPT-54-NAN
page

/ 204

Loading...
bd2ec8690ea8d627ebc8cea60fff754569b0 page 14
Cordless Chain Saw EN
20
“Assembly and Tensioning Chain”.
The circular groove of the guide bar will wear
particularly on the lower edge with time.
When replacing the chain turn the chain bar
180° to allow even wear, thus extending chain
bar life.
Check drive sprocket. If it is worn out or
damaged due to strain, have it exchanged by
an authorized service agent.
If the chain bar is worn out or damaged,
take the chain tensioning catch off the bar
by loosing the screw anti-clockwise. Then
fit the tensioning catch into the new bar by
tightening the screw clockwise. The catch
protrude (a) must be fitted into the bar hole.
(See Fig. W)
SHARPENING CHAIN
WARNING: Remove the battery
pack from the saw before
servicing. Severe injury or death could
occur from electrical shock or body
contact with moving chain.
Cutting edges on chain are sharp. Use
protective gloves when handling chain.
Keep chain sharp. Your saw will cut faster and
more safely. A dull chain will cause undue
sprocket, guide bar, chain, and motor wear. If
you must force chain into wood and cutting
creates only sawdust with few large chips,
chain is dull.
LUBRICATE SPROCKET
WARNING: Wear heavy duty gloves
when performing an maintenance or
service to this tool.
Always remove the battery pack from the saw
before performing any service or maintenance
on this tool.
NOTE: It is not necessary to remove the chain
or bar when lubricating the sprocket.
1. Clean the bar and sprocket.
2. Using a grease gun, insert the tip of the
gun into the lubrication hole and inject
grease until it appears at the outside edge
of the sprocket tip. (See Fig. X)
3. To rotate the sprocket release the chain
stop and pull the chain by hand until the
ungreased side of the sprocket is in line
with the grease hole. Repeat the lubrication
procedure.
CLEANING/STORAGE
Clean the moulded plastic housing of the
chain saw using a soft brush and clean
cloth. Do not use water, solvents or polishes.
Remove all debris, especially from the motor
cooling vents.
Remove and brush clean the cover plate,
chain and chain bar after 1 to 3 hours of use.
Clean the area under the cover plate, the drive
sprocket and chain bar assembly using a soft
brush. Clean oil outlet with a clean cloth.
If the chain saw is to be stored for a longer
period of time, clean chain and chain bar.
Store in a secure, dry place out of the reach of
children.
Do not place other objects on the chain saw.
To prevent leakage ensure machine is left in a
horizontal position (oil filler cap 4 uppermost).
When storing machine in original packaging
the oil tank must be completely emptied.
ENVIRONMENTAL
PROTECTION
This product has been marked with a
symbol relating to removing electric
and electronic waste. This means that
this product shall not be discarded with
household waste but that it shall be returned
to a collection system which conforms to the
European Directive 2002/96/CE. It will then
be recycled or dismantled in order to reduce
the impact on the environment. Electric and
electronic equipment can be hazardous for the
environment and for human health since they
contain hazardous substances.

Chat with your Worx WG368E.9 manual using AI

Get instant AI answers from your Worx WG368E.9 manual

Ask anything about the Worx WG368E.9. Answers come from this manual, with the pages they are based on.

WG368E.9 Maintenance Schedule

Every 10 minutes
Check chain tension during operation

Check recently replaced chain tension about every 10 minutes during operation.

Show in the manual (page 16)
After each use
Inspect saw for damage and alignment

Inspect and maintain saw after each use. Check for damage, binding, or broken parts that may affect safety.

Show in the manual (page 19)
Every 5 hours
Turn guide bar over

Turn the bar over to ensure even wear after every 5 hours of use.

Show in the manual (page 19)
Every time chain is removed
Clean bar rails

Clean the rails every time the chain is removed using a wire brush or similar tool.

Show in the manual (page 19)
Every 1 to 3 hours
Clean cover plate and assembly

Remove and brush clean the cover plate, chain and chain bar after 1 to 3 hours of use.

Show in the manual (page 20)
Every sharpening
Check guide bar condition

Check the condition of the guide bar each time the chain is sharpened to ensure it is not worn or damaged.

Show in the manual (page 19)
M: QW-35-FL

Ask a Question

0/1000

Do you recommend WG368E.9?

Yes No

Frequently Asked Questions

A

The solo version is typically the bare tool only. In many sets, the battery and charger are sold separately, so it is best for users who already own compatible WORX power gear.

Is this answer helpful?

A

It is intended for wood cutting tasks such as branches, logs, planks, beams, and light tree work. It is not suitable for mineral materials, plastic, or masonry.

Is this answer helpful?

A

Yes. The saw uses automatic chain lubrication during operation, but the oil tank must be filled before use. Keeping the chain properly oiled helps reduce wear and improves cutting quality.

Is this answer helpful?

A

The chain should lift about 3 to 6 mm from the guide bar at the center when checked by hand. If it feels loose, adjust it before cutting to reduce kickback risk.

Is this answer helpful?

A

It can be beginner-friendly because of its lock-off switch, visible oil window, and compact size. Still, chainsaws require careful handling, protective gear, and full attention at all times.

Is this answer helpful?

A

Wear eye protection, hearing protection, gloves, and sturdy footwear. A dust mask and protective clothing are also recommended when working around chips, sawdust, and moving chain parts.

Is this answer helpful?

M: OA-GPT-54-NAN

Advantages and Disadvantages

Advantages

  • Cordless 40V Max design gives freedom to work away from outlets.
  • 30 cm guide bar is well suited to pruning and light wood cutting.
  • Automatic chain lubrication helps maintain smoother cutting performance.
  • Low-kickback chain and safety lock features improve user confidence.
VS

Disadvantages

  • Solo version may require a separate battery and charger purchase.
  • Oil must be added before use, or the chain and bar can be damaged.
  • Not intended for heavy-duty logging or cutting non-wood materials.
  • Regular tension checks and maintenance are needed for best results.
M: OA-GPT-54-NAN

Product Specification

Type

Chainsaw

Battery

40V, Li-ion

Bar length

11.81 in

Chain speed

3.8 m/s

Chain oil tank

3.38 fl oz

Features

Additional handle, tool-free chain tensioning, tool-free chain change, automatic chain lubrication, chain brake, chain catch bolt, bucking spike

Vibration level

3.5 m/s^2

Noise level

100 dB(A)

Weight

8.16 lb

Scope of delivery

without charger and battery, incl. guide bar (Oregon), saw chain (Oregon)

M: OA-GPT-54-NAN

Product Description

Worx WG368E.9 Cordless Chainsaw Solo Manual

A practical cordless saw for everyday garden work

The Worx WG368E.9 Cordless chainsaw solo is built for users who want mobile cutting power without the hassle of a cord. Designed for trimming branches, cutting firewood, and handling light timber tasks, it combines a 40V Max lithium-ion platform with a compact 30 cm guide bar and a 25 cm cutting length. The result is a tool that feels manageable, yet still capable enough for regular outdoor maintenance.

One of its biggest strengths is convenience. The solo version is ideal for users who already own compatible WORX batteries, making it a flexible choice for expanding an existing tool setup. The saw is also fairly light for its class, with the bare unit and battery setup kept in a range that supports better control during longer sessions. A chain speed of 3.8 m/s and automatic lubrication help keep cutting smooth, while the low-kickback chain and reduced-kickback bar add a reassuring layer of safety.

The Worx WG368E.9 Cordless chainsaw solo Manual emphasizes careful setup and routine maintenance, and that is part of what makes this model reliable in real use. Chain tension can be adjusted quickly, the oil level is visible at a glance, and the machine is designed to stop accidental starts through a lock-off button and trigger switch combination. For homeowners, this means less guesswork and more confidence when moving from pruning to more demanding cuts.

It is also a thoughtfully engineered saw for seasonal jobs. The 100 ml oil tank, Oregon chain components, and easy-to-follow handling guidance all support consistent performance. Noise and vibration ratings are within the expected range for a cordless chainsaw, but protective gear is still strongly recommended. With proper lubrication, sharp chain upkeep, and safe operating habits, the WG368E.9 can deliver solid results for routine yard care.

Notes

  • Best suited for branches, logs, beams, and general garden cutting.
  • Fill the oil tank before first use; the chain is not pre-oiled.
  • Check chain tension regularly, especially after a new chain is installed.
  • Use eye, ear, and hand protection for safer operation.
  • The solo model is tool-only, so battery and charger may need to be purchased separately.
M: OA-GPT-54-NAN

© Copyright 2026 Manual.ly