Manual.ly Logo

Worx WG368E.9 Manual

0.0 · 0 Ratings

PDF manual · 204 Pages

English

M: OA-GPT-54-NAN
page

/ 204

Loading...
bd2ec8690ea8d627ebc8cea60fff754569b0 page 10
Cordless Chain Saw EN
16
allow metallic objects into your charger
or battery pack connections because
of an electrical failure and hazard will
occur.
NOTE: Your battery pack is UNCHARGED and
you must charge once before use.
The battery charger supplied is matched to
the Li-Ion battery installed in the machine. Do
not use another battery charger.
2. CHARGING YOUR BATTERY PACK
The Li-ion battery is protected against deep
discharging. When the battery is empty,
the machine is switched off by means of a
protective circuit.
In a warm environment or after heavy use, the
battery pack may become too hot to permit
charging. Allow time for the battery to cool
down before recharging.
3. TO REMOVE OR INSTALL BATTERY
PACK (See Fig. G)
Depress the Battery Pack Release Button to
remove the Battery Pack from your tool. After
recharging, insert the Battery Pack into battery
port (See Fig. G). A simple push and slight
pressure will be sufficient until a click is heard.
Check to see if the battery is fully secured.
NOTE: When removing the battery pack,
hold it firmly to avoid dropping and
injury.
4. BATTERY STATUS LED’S (See Fig. H)
NOTE: The Status LED’s will indicate the
battery condition when the button on
the battery is pressed.
The LED’s constantly senses and displays the
battery condition as follows:
Press the button “POWERTEST”, the light
button is illuminated.
When the three green lights are illuminated,
the battery is in a highly charged condition.
When two lights ( ) are illuminated, the
battery is in a moderately charged condition.
When only one green light ( ) is illuminated,
the battery charge is depleted.
IMPORTANT: When only one light is
illuminated, your battery is overly
discharged, even though the tool may
still be capable of working. Continuing
to operate your tool with the battery in
this discharged condition may reduce
the life and performance of your battery.
5. SWITCHING ON AND OFF (See Fig. I)
For switching on the machine, press the
Lock-off Button (3), then fully press the On/Off
Switch (2) and hold in this position. The Lock-
Off Button (3) can now be released.
For switching off, release the On/Off Switch (2).
Cutting
IMPORTANT: Is the oil reservoir
filled? Check the Oil Level Window
(18) prior to starting and regularly
during operation. Refill oil when oil level
is low. A full oil tank will last approx. 20
minutes depending on sawing intensity
and stops (See Fig. J).
Check recent replaced chain tension
about every 10 minutes during
operation.
1. Install the battery pack into the machine
(See Fig. G).
2. Make sure section of log to be cut is not
laying on the ground. This will keep the
Chain (8) from touching the ground as it
cuts through the log. Touching the ground
while the Chain is moving is dangerous
and will dull the Chain.
3. Use both hands to grip saw. Always use
left hand to grip front handle and right
hand to grip rear handle. Use a firm grip.
Thumbs and fingers must wrap around
saw handles (See Fig. K).
4. Make sure your footing is firm. Keep feet
shoulder width apart. Divide your weight
evenly on both feet.
5. When ready to make a cut, push the
Lock-off Button (3) completely in with the
right thumb and squeeze the trigger. This
will turn the saw on. Releasing the trigger
will turn the saw off. Make sure the saw is
running at full speed before starting a cut.
6. When starting a cut, slowly place the
moving chain against the wood. Hold saw
firmly in place to avoid possible bouncing
or skating (sideways movement) of saw.
7. Guide the saw using light pressure and
do not put excessive force on the saw. The

Chat with your Worx WG368E.9 manual using AI

Get instant AI answers from your Worx WG368E.9 manual

Ask anything about the Worx WG368E.9. Answers come from this manual, with the pages they are based on.

WG368E.9 Maintenance Schedule

Every 10 minutes
Check chain tension during operation

Check recently replaced chain tension about every 10 minutes during operation.

Show in the manual (page 16)
After each use
Inspect saw for damage and alignment

Inspect and maintain saw after each use. Check for damage, binding, or broken parts that may affect safety.

Show in the manual (page 19)
Every 5 hours
Turn guide bar over

Turn the bar over to ensure even wear after every 5 hours of use.

Show in the manual (page 19)
Every time chain is removed
Clean bar rails

Clean the rails every time the chain is removed using a wire brush or similar tool.

Show in the manual (page 19)
Every 1 to 3 hours
Clean cover plate and assembly

Remove and brush clean the cover plate, chain and chain bar after 1 to 3 hours of use.

Show in the manual (page 20)
Every sharpening
Check guide bar condition

Check the condition of the guide bar each time the chain is sharpened to ensure it is not worn or damaged.

Show in the manual (page 19)
M: QW-35-FL

Ask a Question

0/1000

Do you recommend WG368E.9?

Yes No

Frequently Asked Questions

A

The solo version is typically the bare tool only. In many sets, the battery and charger are sold separately, so it is best for users who already own compatible WORX power gear.

Is this answer helpful?

A

It is intended for wood cutting tasks such as branches, logs, planks, beams, and light tree work. It is not suitable for mineral materials, plastic, or masonry.

Is this answer helpful?

A

Yes. The saw uses automatic chain lubrication during operation, but the oil tank must be filled before use. Keeping the chain properly oiled helps reduce wear and improves cutting quality.

Is this answer helpful?

A

The chain should lift about 3 to 6 mm from the guide bar at the center when checked by hand. If it feels loose, adjust it before cutting to reduce kickback risk.

Is this answer helpful?

A

It can be beginner-friendly because of its lock-off switch, visible oil window, and compact size. Still, chainsaws require careful handling, protective gear, and full attention at all times.

Is this answer helpful?

A

Wear eye protection, hearing protection, gloves, and sturdy footwear. A dust mask and protective clothing are also recommended when working around chips, sawdust, and moving chain parts.

Is this answer helpful?

M: OA-GPT-54-NAN

Advantages and Disadvantages

Advantages

  • Cordless 40V Max design gives freedom to work away from outlets.
  • 30 cm guide bar is well suited to pruning and light wood cutting.
  • Automatic chain lubrication helps maintain smoother cutting performance.
  • Low-kickback chain and safety lock features improve user confidence.
VS

Disadvantages

  • Solo version may require a separate battery and charger purchase.
  • Oil must be added before use, or the chain and bar can be damaged.
  • Not intended for heavy-duty logging or cutting non-wood materials.
  • Regular tension checks and maintenance are needed for best results.
M: OA-GPT-54-NAN

Product Specification

Type

Chainsaw

Battery

40V, Li-ion

Bar length

11.81 in

Chain speed

3.8 m/s

Chain oil tank

3.38 fl oz

Features

Additional handle, tool-free chain tensioning, tool-free chain change, automatic chain lubrication, chain brake, chain catch bolt, bucking spike

Vibration level

3.5 m/s^2

Noise level

100 dB(A)

Weight

8.16 lb

Scope of delivery

without charger and battery, incl. guide bar (Oregon), saw chain (Oregon)

M: OA-GPT-54-NAN

Product Description

Worx WG368E.9 Cordless Chainsaw Solo Manual

A practical cordless saw for everyday garden work

The Worx WG368E.9 Cordless chainsaw solo is built for users who want mobile cutting power without the hassle of a cord. Designed for trimming branches, cutting firewood, and handling light timber tasks, it combines a 40V Max lithium-ion platform with a compact 30 cm guide bar and a 25 cm cutting length. The result is a tool that feels manageable, yet still capable enough for regular outdoor maintenance.

One of its biggest strengths is convenience. The solo version is ideal for users who already own compatible WORX batteries, making it a flexible choice for expanding an existing tool setup. The saw is also fairly light for its class, with the bare unit and battery setup kept in a range that supports better control during longer sessions. A chain speed of 3.8 m/s and automatic lubrication help keep cutting smooth, while the low-kickback chain and reduced-kickback bar add a reassuring layer of safety.

The Worx WG368E.9 Cordless chainsaw solo Manual emphasizes careful setup and routine maintenance, and that is part of what makes this model reliable in real use. Chain tension can be adjusted quickly, the oil level is visible at a glance, and the machine is designed to stop accidental starts through a lock-off button and trigger switch combination. For homeowners, this means less guesswork and more confidence when moving from pruning to more demanding cuts.

It is also a thoughtfully engineered saw for seasonal jobs. The 100 ml oil tank, Oregon chain components, and easy-to-follow handling guidance all support consistent performance. Noise and vibration ratings are within the expected range for a cordless chainsaw, but protective gear is still strongly recommended. With proper lubrication, sharp chain upkeep, and safe operating habits, the WG368E.9 can deliver solid results for routine yard care.

Notes

  • Best suited for branches, logs, beams, and general garden cutting.
  • Fill the oil tank before first use; the chain is not pre-oiled.
  • Check chain tension regularly, especially after a new chain is installed.
  • Use eye, ear, and hand protection for safer operation.
  • The solo model is tool-only, so battery and charger may need to be purchased separately.
M: OA-GPT-54-NAN

© Copyright 2026 Manual.ly