Manual.ly Logo

Worx WG329E.9 Manual

0.0 · 0 Ratings

PDF manual · 176 Pages

English

M: OA-GPT-54-NAN
page

/ 176

Loading...
726c4fbc3fc8d8d9ecd75aec27e0f5203c03 page 12
18
Cordless Limbing and Trimming Chain Saw
EN
WARNING: (See Fig. X)
• If on slope, make sure log will not
roll down hill. Secure log by using
wooden stakes. Drive wooden stakes
into ground on downhill side of log.
Stand on uphill side of log while
cutting. Log may roll after cutting.
(See Fig. X)
• Never try cutting through two logs
at same time. This could increase the
risk of kickback.
• While cutting log, never hold log with
your hand or leg.
• While cutting log, never allow another
person to hold log.
• Turn off and remove the battery pack
from the saw before moving from one
place to another.
SAW MAINTENANCE AND
KICKBACK SAFETY
Follow maintenance instructions in this
manual. Proper cleaning and maintenance of
the Saw Chain (8) and Guide Bar (7), as well as
the JAWSAW
®
in general, can reduce chances
of kickback. Inspect and maintain saw after
each use. This will increase the service life of
your saw.
NOTE: Even with proper sharpening, risk of
kickback can increase with each sharpening.
MAINTENANCE AND
STORAGE OF JAWSAW
®
1. Remove the battery pack from the saw:
• When not in use.
• When transporting.
• When left unattended.
• Before servicing.
• Before cleaning.
• Before changing accessories or
attachments, such as Saw Chain and
Guard Bar.
2. Inspect the saw before and after each use
for:
• Any signs of damage.
• Smooth action of push handle and
movement of bar.
• Adequate Chain Tension; you should be
able to lift the Saw Chain from the Guide
Bar no more than 3 mm.
• Adequate chain lubrication.
3. Do not use the JAWSAW
®
, if:
• The Trigger Switch (2) or Lock Out Button
(3) is malfunctioning.
• The Rear (Push) Handle (1) does not
smoothly return under spring force.
• Any other damage which affects the safety
or operation is evident.
4. Maintain the JAWSAW
®
with care and
have any damage or malfunction repaired
by an authorized service center:
• Never expose the JAWSAW
®
to rain.
• Keep Saw Chain sharp, clean, and
lubricated for better and safer
performance.
• Follow steps outlined in this manual to
sharpen Saw Chain.
• Keep handles clean and free from oil.
• Keep all screws and nuts tight.
5. When servicing, use only identical
replacement parts.
6. When not in use, always store JAWSAW
®
• In a high or locked place, out of children’s
reach.
• In a dry place.
REPLACING SAW CHAIN/CHAIN BAR
Replace the Saw Chain when cutters are too
worn to sharpen or when chain breaks. Only
use replacement chain noted in this manual.
Always include new drive Sprocket (16) when
replacing the Saw Chain. This will maintain
proper driving of chain. Inspect Guide Bar (7)
before sharpening chain. A worn or damaged
guide bar is unsafe. A worn or damaged Guide
Bar is unsafe, will damage the Saw Chain, and
will make cutting harder.
For Replacing the Guide Bar please refer to
CHANGING THE GUIDE BAR AND CHAIN
section in the Adjustment and Assembly
Instructions.
SHARPENING SAW CHAIN
WARNING: Remove the battery
pack from the saw before servicing.
Cutting edges on chain are sharp. Use
protective gloves when handling chain.

Chat with your Worx WG329E.9 manual using AI

Get instant AI answers from your Worx WG329E.9 manual

Ask anything about the Worx WG329E.9. Answers come from this manual, with the pages they are based on.

WG329E.9 Maintenance Schedule

Before every use
Check chain tension

Ensure chain can be pulled away from guide bar approx 3 mm and snaps back. Check around every 10 minutes during operation with new chain.

Show in the manual (page 14)
During operation
Check oil level and lubrication

Check oil level window before starting and regularly during use. Ensure slight oil presence is visible on chain and bar.

Show in the manual (page 15)
After each use
Inspect saw for damage

Check for signs of damage, smooth handle action, adequate chain tension, and proper lubrication before and after every use.

Show in the manual (page 18)
After each use
Clean debris from tool

Open chain access cover to remove trapped debris and clean ventilation slots with a dry brush.

Show in the manual (page 19)
As needed
Lubricate chainwheel

Inject grease into lubrication hole until it appears at outside edge of chainwheel tip using a grease gun.

Show in the manual (page 19)
When worn
Replace saw chain

Replace chain when cutters are too worn to sharpen or if the chain breaks. Always include a new drive sprocket.

Show in the manual (page 18)
M: QW-35-FL

Ask a Question

0/1000

Do you recommend WG329E.9?

Yes No

Frequently Asked Questions

A

It is intended for pruning branches and cutting small logs in wood only. The manual specifically warns not to use it for cutting metals or non-wood building materials. Stick to the wood use case and follow the size guidance for safer, better performance.

Is this answer helpful?

A

The saw uses a chain oil tank (30 ml) and an automatic oiler. The manual states it is shipped with an empty oil tank, so you must fill with chain bar oil before use. Check the oil level window regularly and refill if low. If the chain appears dry, ensure the oil hole in the bar is not blocked.

Is this answer helpful?

A

You should periodically check chain tension during use. The manual highlights re-checking around every 10 minutes when using a newly replaced chain. It also advises that you should be able to pull the chain about 3 mm away from the guide bar and have it snap back.

Is this answer helpful?

A

Yes. The tool includes two lock-out buttons to support upright cutting (down from the top) and inverted cutting (up from the bottom). Select the appropriate lock-out, then operate the trigger as described while maintaining secure footing.

Is this answer helpful?

A

Use both hands with correct grip, keep safety items in place, and never force the cut. Wear eye protection and hearing protection, and follow kickback guidance like avoiding contact with the guide bar nose and avoiding dull or loose chains. Always remove the battery before adjusting the chain or guide bar.

Is this answer helpful?

A

The manual points to common causes such as incorrect chain direction, incorrect chain tension, or a worn chain needing replacement. If the chain is installed backwards, it will not cut effectively. Confirm chain orientation, then verify tension and lubrication, and sharpen or replace the chain if needed.

Is this answer helpful?

M: OA-GPT-54-NAN

Advantages and Disadvantages

Advantages

  • Cordless pruning tool with 20V Max PowerShare platform for limb and small-log cutting.
  • Automatic oiler with an oil level window helps keep the bar and chain lubricated during cutting.
  • Supports both upright and inverted cutting orientations via lock-out buttons for more flexible pruning.
  • Guided chain tensioning process; includes an easy-to-verify snap-back tension check.
  • Jaw saw intended for wood (up to 100 mm), matching typical trimming and limbing needs.
VS

Disadvantages

  • Not intended for metals or non-wood materials; use is restricted to wood pruning tasks.
  • Requires chain oil before use; shipped with empty oil tank and cannot be run dry.
  • Safety requirements are strict: gloves, eye/hearing protection, and careful kickback handling are emphasized.
  • If chain tension or lubrication is off, cutting performance may drop and the chain or motor may overheat.
  • Tool-only configuration typically means you need a compatible battery and charger separately.
M: OA-GPT-54-NAN

Product Specification

Type

Pruning Saw

Battery

20V, Li-Ion

Bar Length

5.91in

Chain Speed

8.20ft/s

Chain Oil Tank

1.01fl oz

Features

tool-free chain tensioning, automatic chain lubrication, claw stop

Vibration Level

5.60m/s²

Noise Level

82dB(A)

Weight

7.06lb

Scope of Delivery

without charger and battery

M: GO-GEM-FL-25

Product Description

Worx WG329E.9 20V PowerShare Cordless Limb Saw (tool only) Manual

A cordless jaw saw for cleaner pruning cuts

The Worx WG329E.9 20V PowerShare Cordless Limb Saw is designed for limb removal and trimming, helping you cut through branches and small logs with a controlled jaw-saw action. It is intended for wood only, including pruning work and cutting small logs up to 100 mm diameter, making it a practical choice for yard maintenance and storm cleanup.

With a 20V Max battery system, a 150 mm guide bar, 6.4 mm chain pitch, and a chain speed of 2.54 m/s, this cordless saw focuses on manageable power for typical pruning tasks. The tool uses an oil tank (30 ml) and an automatic oiler, so the cutting system stays lubricated during use.

Control and setup built into the tool

For safety and ease of operation, the saw includes a rear handle with a trigger switch plus lock-out buttons that support upright (cutting down from the top) and inverted (cutting up from the bottom) cutting positions. Before each job, you check the oil level window, verify chain tension, and ensure the chain stops when the trigger is released.

Chain tension is designed to be easy to adjust, and the instructions emphasize periodic re-checking, especially after fitting a new chain. Lubrication is critical: the manual notes the saw ships with an empty oil tank and should never be run without chain oil, as it can cause poor cutting performance, motor overload, and possible damage.

Key highlights (most important results)

  • Designed for wood pruning and trimming, with intended capacity for branches and small logs up to 100 mm diameter.
  • Includes automatic chain oiling with an oil level window, supporting consistent lubrication at low chain speeds.
  • Tool-less in feel, but not tool-free: chain tensioning and guide bar or chain changes follow a guided, safety-first process.
  • Supports two cutting orientations using lock-out buttons, improving flexibility for different limb positions.

Notes

  • Wear eye protection and hearing protection, and follow chain lubrication, tensioning, and kickback safety guidance.
  • Always remove the battery before adjustments or chain handling.
  • Use the recommended bar and chain specifications and use fresh, approved chain oil to help protect the tool and warranty.
M: OA-GPT-54-NAN

© Copyright 2026 Manual.ly