Manual.ly Logo

Worx WG325E Manual

0.0 · 0 Ratings

PDF manual · 260 Pages

English

M: QW-35-FL
page

/ 260

Loading...
2414400d68391fdf77b0dee60a6e68ff10bf page 15
21
Cordless Pruning Saw EN
Bar Maintenance
To maximize bar life, the following bar maintenance
is recommended.
The bar rails that carry the chain should be cleaned
before storing the tool or if the bar or chain appear
to be dirty.
The rails should be cleaned every time the chain is
removed.
To clean the Bar rails.
1. Remove Housing-Cover, Bar and Chain. (see
section ASSEMBLY)
2. Using a wire brush, screwdriver or similar tool,
clear the residue from the inner groove of the
bar. (See Fig. Q)
3. Make sure to clean oil passages thoroughly.
Conditions which require Chain and Guide Bar
maintenance:
• Saw cuts to one side or at an angle.
• Saw has to be forced through the cut.
• Inadequate supply of oil to the bar and chain.
Check the condition of the Guide Bar each time the
chain is sharpened. A worn Guide Bar will damage

After each use, remove the battery pack, clean all
sawdust from the Guide Bar and sprocket hole.

square edges and sides.
Replace the Guide Bar when the groove is worn,
the Guide Bar is bent or cracked, or when excess
heating or burring of the rails occurs.
File Rail Edges
and Sides
Square
Worn Groove Correct Groove
If replacement is necessary, use only the Guide Bar

the decal located on the pruning saw.
Replacing Bar & Chain
Replace chain when cutters are too worn to sharpen
or when chain stops. Only use replacement chain
noted in this manual.
Inspect Guide Bar before sharpening chain. A
worn or damaged Guide Bar is unsafe. A worn or
damaged Guide Bar will damage chain. It will also
make cutting harder.
SHARPENING SAW CHAIN




Cutting edges on chain are sharp. Use protective
gloves when handling chain.


of 30° to the guide bar.
Keep chain sharp. Your saw will cut faster and more
safely. A dull chain will cause undue sprocket, Guide
Bar, chain, and motor wear. If you must force chain
into wood and cutting creates only sawdust with
few large chips, chain is dull.
6. ENVIRONMENTAL
PROTECTION
Waste electrical products must not be
disposed of with household waste. Please
recycle where facilities exist. Check with
your local authorities or retailer for recycling
advice.
FOR BATTERY TOOLS
The ambient temperature range for the use and
storage of tool and battery is 0 °C-45 °C.
The recommended ambient temperature range for
the charging system during charging is 0 °C-40 °C.

Chat with your Worx WG325E manual using AI

Get instant AI answers from your Worx WG325E manual

Ask anything about the Worx WG325E. Answers come from this manual, with the pages they are based on.

WG325E Maintenance Schedule

Every 10 minutes
Check chain tension during operation

The manual advises checking the recently replaced chain tension about every 10 minutes while cutting. Tighten if the chain becomes loose around the guide bar.

Show in the manual (page 19)
After each use
Inspect and clean saw after each use

Remove battery pack, inspect for damage or misalignment, and clean all sawdust from the guide bar and sprocket hole. Store in a dry place with cover on.

Show in the manual (page 20)
Each time chain is removed
Clean guide bar rails

Use a wire brush or screwdriver to clear residue from the inner groove of the bar and ensure oil passages are thoroughly cleaned.

Show in the manual (page 21)
Each time chain is sharpened
Check condition of guide bar

Inspect the guide bar for wear, bending, or cracking whenever you sharpen the chain. Replace if the groove is worn or rails show excessive heating/burring.

Show in the manual (page 21)
M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend WG325E?

Yes No

Frequently Asked Questions

A

Charge until light indicates full status using the compatible 20V charger included in the accessory kit.

Is this answer helpful?

A

Wear goggles gloves ear protection and sturdy footwear to ensure safety during operation.

Is this answer helpful?

A

Adjust cover knob until chain lifts half drivlink depth from guide bar in center area.

Is this answer helpful?

A

Dry conditions recommended to prevent binding and slip which could cause dangerous kickback events.

Is this answer helpful?

A

Every twenty cuts or when producing sawdust instead of chips indicating dull edges.

Is this answer helpful?

A

Lockable dry place out of children reach when idle to prevent unauthorized access.

Is this answer helpful?

A

Consult Positec Germany GmbH or local authorized service center for specific terms and coverage.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Cordless design eliminates trip hazards and cord management issues during garden work.
  • Compatible with 20V PowerShare battery platform for shared energy resources across tools.
  • Extension pole increases reach allowing trimming of high branches without ladders.
  • Automatic oiler maintains lubrication reducing friction and extending component lifespan effectively.
  • Lightweight construction at 1.1 kg reduces operator fatigue during prolonged pruning sessions.
VS

Disadvantages

  • 12 cm bar length limits cutting capacity preventing work on very thick trunks.
  • Noise emission reaches 84 dB requiring hearing protection for extended usage periods.
  • Chain tension loosens quickly requiring frequent manual re-tightening after initial use.
  • Not suitable for tree felling operations due to size and design limitations stated.
  • Requires purchasing specific replacement chains meeting strict gauge specifications for safety.
M: QW-35-FL

Product Specification

Type

Pole Saw

Bar Length

4.72 in

Chain Speed

32.81 ft/s

Features

Brushless motor, tool-less chain tensioning, tool-less chain replacement, automatic chain lubrication, chain brake

Vibration Level

9.51 ft/s^2

Noise Level

94 dB(A)

Weight

1.98 lb

M: QW-35-FL

Product Description

Comprehensive Guide to Worx WG325E 20V PowerShare Cordless Branch Saw

Welcome to our detailed guide on the Worx WG325E 20V PowerShare Cordless Branch Saw. Garden enthusiasts often struggle with reaching high branches safely using traditional ladders. This versatile tool offers a cordless solution that enhances productivity while reducing physical strain significantly. It is essential to read the Worx WG325E 20V PowerShare Cordless Branch Saw Manual carefully prior to assembly. Understanding the components prevents accidents during operation effectively.

Technical Specifications

The machine operates on a maximum voltage of 20 volts nominal 18 volts power for efficient performance. It comes with a short 12 centimeter guide bar designed for pruning limbs rather than felling large trees. The total weight including chain and bar is approximately 1.1 kilograms making it manageable for extended use indoors or outdoors. An optional extension pole extends reach up to 275 centimeters maximum cutting height safely. This feature allows users to trim canopy branches from ground level without instability risks.

Assembly and Operation

Mounting the chain requires attention to direction arrows printed on the metal bar surface. Proper tension ensures the drive links stay seated securely on the sprocket teeth always. Lubrication checks are mandatory because the automatic oiler fills the track continuously during cutting. Users must verify oil flow by pointing the tip at cardboard before heavy cutting begins. Never force the motor through thick wood as this causes overheating and potential motor damage permanently.

Safety Protocols

Kickback is a significant risk if the nose touches obstacles or wood pinches the chain tightly. Operators should stand slightly to the left of the saw path to avoid injury from debris. Protective gear including gloves goggles and ear protection minimizes exposure to loud noise and flying fragments. Do not cut overhead unless branches are secured first firmly. Falling limbs can rebound unexpectedly causing severe personal harm instantly.

Maintenance Requirements

Sharp chains cut faster and reduce vibration exposure significantly over time. File every link maintaining a 30 degree angle relative to the guide bar rails. Clean sawdust residue from air vents after each session to keep cooling working. Store batteries at room temperature away from direct sunlight to preserve capacity. Recycle electrical waste according to local regulations to protect the environment properly.

Operational Notes

Inspect the condition of the chain guard daily before powering on the unit. Troubleshoot intermittent issues by checking battery connections immediately for corrosion. Avoid using damp locations without residual current devices installed nearby for shock prevention. Keep all loose clothing tied back away from rotating parts entirely to prevent entanglement. Maintain records of service intervals for warranty purposes and future reference needs. Happy pruning!

M: QW-35-FL

© Copyright 2026 Manual.ly