Manual.ly Logo

Worx WG325E Manual

0.0 · 0 Ratings

PDF manual · 260 Pages

English

M: QW-35-FL
page

/ 260

Loading...
2414400d68391fdf77b0dee60a6e68ff10bf page 14
20
Cordless Pruning Saw EN
recommended.
• Never use a dull or loose chain. Keep chain
sharp with proper tension.

1. Use the pruning saw only with secure footing.
2. Hold the pruning saw at the right-hand side of
your body (See Fig. L).
3. The Chain must be running at full speed before it
makes contact with the wood.
4. Use the Base Plate to secure the saw onto the
wood before starting to cut.
5. Use the Base Plate as a leverage point while
cutting. (See Fig. M)
6. Do not operate the saw with arms fully extended,

or stand on a ladder while sawing. (See Fig. N)
Never use the pruning saw above shoulder height.
Cutting wood under tension (See Fig. O)



could spring back and strike operator causing

When sawing logs supported on both ends, start the


below, in order to avoid contact of the pruning saw
with the ground. When sawing logs supported on


the cut from above (Z) in order to avoid log splitting

OPERATION FOR POLE SAW
Cutting with extension pole
1. Install the battery pack into the machine.
2. Before cutting a high branch, consider all the
same points detailed in the previous section
“Trimming Branches” but pay particular
attention to the likely path of the falling branch.





from all power lines. (See Fig. P1-P4)
3. Use both hands to grip Pole Saw. Use only
designated grip areas when operating Pole Saw

must wrap around Pole Saw handle and pole.
 
Divide your weight evenly on both feet.
5. When ready to make a cut, press the Lock-out

Fig. P6). This will turn Pole Saw on. Releasing

saw is running at full speed before starting a cut.
6. When starting a cut, place moving chain

avoid possible bouncing or skating (sideways
movement) of saw.
7. Guide Pole Saw using light pressure. Do not
force Pole Saw. The motor will overload and can

rate for which it was intended.
8. Remove Pole Saw from a cut with saw running
at full speed. Stop Pole Saw by releasing trigger.
Make sure chain has stopped before setting
Pole Saw down.
CLEAN RESIDUAL OIL AFTER OPERATION
Lift the Chain Guard to the maximum position for 3
to 5 times. (See Fig.G2)

people. The Chain and Guide bar should be faced
down.
SAW MAINTENANCE
Follow maintenance instructions in this manual.
Proper cleaning of saw and chain and Guide Bar
maintenance can reduce chances of kickback.
Inspect and maintain saw after each use. This will
increase the service life of your saw.
 Even with proper sharpening, risk of
kickback can increase with each sharpening.
MAINTENANCE AND STORAGE OF PRUNING SAW
1. Remove the battery pack
• When not in use
• Before moving from one place to another
• Before servicing
• Before changing accessories or attachments,
such as saw chain and guard
2. Inspect pruning saw before and after each
use. Check saw closely if guard or other part
has been damaged. Check for any damage
that may affect operator safety or operation of
saw. Check for alignment or binding of moving
parts. Check for broken or damaged parts. Do
not use pruning saw if damage affects safety or
operation. Have damage repaired by authorized
service center. To locate an authorized service
center, visit www.worx.com.
3. Maintain pruning saw with care.
• Never expose saw to rain or direct moisture.
• Keep chain sharp, clean, and lubricated for
better and safer performance.
• Follow steps outlined in this manual to sharpen
chain.
• Keep handles dry, clean, and free of oil and
grease.
• Keep all screws and nuts tight.
4. When servicing, use only identical replacement
parts.
5. When not in use, always store pruning saw
• in a high or locked place, out of children’s reach
• in a dry place
• with Bar and Housing Cover in place

Chat with your Worx WG325E manual using AI

Get instant AI answers from your Worx WG325E manual

Ask anything about the Worx WG325E. Answers come from this manual, with the pages they are based on.

WG325E Maintenance Schedule

Every 10 minutes
Check chain tension during operation

The manual advises checking the recently replaced chain tension about every 10 minutes while cutting. Tighten if the chain becomes loose around the guide bar.

Show in the manual (page 19)
After each use
Inspect and clean saw after each use

Remove battery pack, inspect for damage or misalignment, and clean all sawdust from the guide bar and sprocket hole. Store in a dry place with cover on.

Show in the manual (page 20)
Each time chain is removed
Clean guide bar rails

Use a wire brush or screwdriver to clear residue from the inner groove of the bar and ensure oil passages are thoroughly cleaned.

Show in the manual (page 21)
Each time chain is sharpened
Check condition of guide bar

Inspect the guide bar for wear, bending, or cracking whenever you sharpen the chain. Replace if the groove is worn or rails show excessive heating/burring.

Show in the manual (page 21)
M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend WG325E?

Yes No

Frequently Asked Questions

A

Charge until light indicates full status using the compatible 20V charger included in the accessory kit.

Is this answer helpful?

A

Wear goggles gloves ear protection and sturdy footwear to ensure safety during operation.

Is this answer helpful?

A

Adjust cover knob until chain lifts half drivlink depth from guide bar in center area.

Is this answer helpful?

A

Dry conditions recommended to prevent binding and slip which could cause dangerous kickback events.

Is this answer helpful?

A

Every twenty cuts or when producing sawdust instead of chips indicating dull edges.

Is this answer helpful?

A

Lockable dry place out of children reach when idle to prevent unauthorized access.

Is this answer helpful?

A

Consult Positec Germany GmbH or local authorized service center for specific terms and coverage.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Cordless design eliminates trip hazards and cord management issues during garden work.
  • Compatible with 20V PowerShare battery platform for shared energy resources across tools.
  • Extension pole increases reach allowing trimming of high branches without ladders.
  • Automatic oiler maintains lubrication reducing friction and extending component lifespan effectively.
  • Lightweight construction at 1.1 kg reduces operator fatigue during prolonged pruning sessions.
VS

Disadvantages

  • 12 cm bar length limits cutting capacity preventing work on very thick trunks.
  • Noise emission reaches 84 dB requiring hearing protection for extended usage periods.
  • Chain tension loosens quickly requiring frequent manual re-tightening after initial use.
  • Not suitable for tree felling operations due to size and design limitations stated.
  • Requires purchasing specific replacement chains meeting strict gauge specifications for safety.
M: QW-35-FL

Product Specification

Type

Pole Saw

Bar Length

4.72 in

Chain Speed

32.81 ft/s

Features

Brushless motor, tool-less chain tensioning, tool-less chain replacement, automatic chain lubrication, chain brake

Vibration Level

9.51 ft/s^2

Noise Level

94 dB(A)

Weight

1.98 lb

M: QW-35-FL

Product Description

Comprehensive Guide to Worx WG325E 20V PowerShare Cordless Branch Saw

Welcome to our detailed guide on the Worx WG325E 20V PowerShare Cordless Branch Saw. Garden enthusiasts often struggle with reaching high branches safely using traditional ladders. This versatile tool offers a cordless solution that enhances productivity while reducing physical strain significantly. It is essential to read the Worx WG325E 20V PowerShare Cordless Branch Saw Manual carefully prior to assembly. Understanding the components prevents accidents during operation effectively.

Technical Specifications

The machine operates on a maximum voltage of 20 volts nominal 18 volts power for efficient performance. It comes with a short 12 centimeter guide bar designed for pruning limbs rather than felling large trees. The total weight including chain and bar is approximately 1.1 kilograms making it manageable for extended use indoors or outdoors. An optional extension pole extends reach up to 275 centimeters maximum cutting height safely. This feature allows users to trim canopy branches from ground level without instability risks.

Assembly and Operation

Mounting the chain requires attention to direction arrows printed on the metal bar surface. Proper tension ensures the drive links stay seated securely on the sprocket teeth always. Lubrication checks are mandatory because the automatic oiler fills the track continuously during cutting. Users must verify oil flow by pointing the tip at cardboard before heavy cutting begins. Never force the motor through thick wood as this causes overheating and potential motor damage permanently.

Safety Protocols

Kickback is a significant risk if the nose touches obstacles or wood pinches the chain tightly. Operators should stand slightly to the left of the saw path to avoid injury from debris. Protective gear including gloves goggles and ear protection minimizes exposure to loud noise and flying fragments. Do not cut overhead unless branches are secured first firmly. Falling limbs can rebound unexpectedly causing severe personal harm instantly.

Maintenance Requirements

Sharp chains cut faster and reduce vibration exposure significantly over time. File every link maintaining a 30 degree angle relative to the guide bar rails. Clean sawdust residue from air vents after each session to keep cooling working. Store batteries at room temperature away from direct sunlight to preserve capacity. Recycle electrical waste according to local regulations to protect the environment properly.

Operational Notes

Inspect the condition of the chain guard daily before powering on the unit. Troubleshoot intermittent issues by checking battery connections immediately for corrosion. Avoid using damp locations without residual current devices installed nearby for shock prevention. Keep all loose clothing tied back away from rotating parts entirely to prevent entanglement. Maintain records of service intervals for warranty purposes and future reference needs. Happy pruning!

M: QW-35-FL

© Copyright 2026 Manual.ly