Manual.ly Logo

Worx WG303E Manual

0.0 · 0 Ratings

PDF manual · 24 Pages

English

M: OA-GPT-54-NAN
page

/ 24

Loading...
e0222770237ee0088a877b64a5ce2be4e877 page 12
Chain Saw WG303E
18
When the log is supported on both ends, as illustrated,
cut 1/3 the diameter from the top overbuck. Then make
the finished cut by underbucking the lower 2/3 to meet
the first cut (See Fig. Q).
WARNING (See Fig. R)
• If on slope, make sure log will not roll down hill.
Secure log by using wooden stakes. Drive wooden
stakes into ground on downhill side of log. Stand
on uphill side of log while cutting. Log may roll after
cutting.
• Never try cutting through two logs at same time. This
could increase the risk of kickback.
• While cutting log, never hold log with your hand, leg,
or foot.
• While cutting log, never allow another person to hold
log.
• Turn off and unplug saw before moving from one
place to another.
MAINTENANCE
Before any work on the machine itself, pull the
mains plug from the socket.
NOTE: To ensure long and reliable service, carry out the
following maintenance regularly.
Regularly check for obvious defects such as loose,
dislodged or damaged chain and guide bar, loose
fixings and worn or damaged components.
Check that covers and guards are undamaged and
correctly fitted. Carry out necessary maintenance or
repairs before using the chain saw.
If the chain saw should happen to fail despite the care
taken in manufacturing and testing, repair should be
carried out by an authorized customer service agent.
Before returning, ensure all oil in the oil tank has
been emptied.
BAR MAINTENANCE
To maximize bar life, the following bar maintenance is
recommended.
The bar rails that carry the chain should be cleaned
before storing the tool or if the bar or chain appear to be
dirty.
The rails should be cleaned every time the chain is
removed.
TO CLEAN THE BAR RAILS:
1. Remove chain cover and bar and chain (see section
ASSEMBLY).
1
2
2/3
1/3
Q
R

Chat with your Worx WG303E manual using AI

Get instant AI answers from your Worx WG303E manual

Ask anything about the Worx WG303E. Answers come from this manual, with the pages they are based on.

WG303E Maintenance Schedule

Every 10 minutes
Check chain tension

Check recently replaced chain tension about every 10 minutes during operation to ensure proper tightness.

Show in the manual (page 14)
After each use
Clean sawdust from guide bar and sprocket

With unit disconnected from power source, clean all sawdust from the guide bar and sprocket hole after each use.

Show in the manual (page 19)
When removing chain
Clean bar rails

Clean the inner groove of the bar with a wire brush or screwdriver and clear oil passages thoroughly when the chain is removed.

Show in the manual (page 18)
Every 1-3 hours
Clean cover plate and assembly

Remove and brush clean the cover plate, chain and chain bar after 1 to 3 hours of use.

Show in the manual (page 20)
Every time sharpening
Check guide bar condition

Check the condition of the guide bar each time the chain is sharpened to identify wear or damage.

Show in the manual (page 19)
As needed
Lubricate drive sprocket

Inject grease into the lubrication hole until it appears at the outside edge of the sprocket tip using a grease gun.

Show in the manual (page 20)
M: QW-35-FL

Ask a Question

0/1000

Do you recommend WG303E?

Yes No

Frequently Asked Questions

A

Yes. It is intended for sawing trees, tree trunks, branches, wooden beams, and planks. The guidance specifically warns against cutting mineral materials and non-wood building materials, since using the chainsaw outside its intended purpose can create hazardous situations and poor cutting results.

Is this answer helpful?

A

Before use, the saw must be filled with the recommended bar and chain oil; do not run it dry or with an empty tank. To verify the automatic oiler, run the saw and point the guide bar tip toward cardboard or paper on the ground. If an increasing oil pattern appears, the oiler is operating correctly; if not, contact service.

Is this answer helpful?

A

The correct tension is reached when the chain can be raised about 3-6mm from the bar in the center. Recheck often when using a new chain, since it will stretch early. Always unplug before adjusting tension, and ensure the chain rotates freely without kinks.

Is this answer helpful?

A

The chain stop lever (hand guard) is designed to stop the chain quickly when activated, including in some kickback scenarios where the operator hand strikes the lever. The saw should be checked regularly so that, with the hand guard pushed forward and the saw started, the chain does not move.

Is this answer helpful?

A

Use both hands with a firm grip so thumbs and fingers wrap the handles. Do not overreach or cut above shoulder height. Avoid letting the guide bar nose touch anything while the chain is moving. Use the correct replacement bar and chain, keep the chain sharp and properly tensioned, and watch for pinching or wood shifting.

Is this answer helpful?

A

Check for power issues first, then inspect the extension cord and connections. If a fuse is faulty, replace it. If the hand guard safety is not in the correct position, pull it back. If these are fine but problems continue, internal wiring or the switch may be defective and should be handled by a service agent.

Is this answer helpful?

M: OA-GPT-54-NAN

Advantages and Disadvantages

Advantages

  • 2000W corded power for steady cutting of trees, branches, beams, and planks
  • Low-kickback chain and reduced kickback guide bar to lower kickback risk
  • Chain stop lever (hand guard) designed to quickly stop the chain when activated
  • Automatic oiler helps maintain lubrication during operation for better cutting performance
  • Automatic chain tensioning knob with ratchet supports more consistent tension checks
VS

Disadvantages

  • Corded operation requires extension cords and correct voltage/current supply
  • Requires regular oil filling and periodic oil and chain tension inspections
  • Not suitable for cutting mineral materials, plastic, masonry, or non-wood building materials
  • Safety rules limit cutting height and require two-handed operation, reducing flexibility
  • Maintenance is important: bar groove cleaning and sprocket lubrication help prevent wear
M: OA-GPT-54-NAN

Product Specification

Type

Chainsaw

Power

2000W

Bar length

15.75 in

Chain speed

39.37 ft/s

Chain pitch

3/8"

Chain oil tank

6.76 fl oz

Special features

Additional handle, tool-free chain tensioning, automatic chain lubrication, chain brake, chain catch bolt, bumper spike

Weight

10.58 lb

Scope of delivery

Guide bar, saw chain, bar protector

M: GO-GEM-FL-25

Product Description

Worx WG303E Electric Chainsaw

The Worx WG303E Electric Chainsaw is a corded 2000W chainsaw built for confident, everyday cutting of trees, trunks, branches, and wooden beams or planks. With a 400mm bar and a fast 12m/s chain speed, it is designed to help you move from setup to sawing with less hassle, while still emphasizing control and operator safety.

Safety-first design for more controlled cuts

Designed to lower the risk of kickback, the WG303E uses a low-kickback chain and a reduced kickback guide bar. It also includes a chain stop lever (hand guard) that quickly stops the chain when activated, helping protect you in sudden situations. You start it with a lock-off button and on/off switch, and for proper operation the saw should be held with both hands on the handles, keeping your body positioned safely and your cutting height controlled.

Performance and day-to-day operation

The automatic oiler helps keep cutting performance consistent. Before you begin, check the oil level window and refill the 200ml tank as needed. During use, you should periodically inspect chain tension and make sure the chain runs smoothly without kinks, since new chains can stretch during early operation. For best results, aim for correct tension so the chain can be lifted about 3-6mm from the bar in the middle, while still rotating freely.

Practical cutting guidance for real jobs

The saw is intended for wood only, not mineral materials. For cutting logs, safe technique matters: overbuck and underbuck methods help match support conditions, and on slopes you should stand on the uphill side. When working with limbs under tension, proceed with extreme caution because release can cause spring back. For felling, plan an escape route and use correct notching and felling back-cut steps to guide the tree's direction.

Key takeaways (most important results)

  • Low-kickback chain and guide bar reduce, but do not eliminate, kickback risk
  • Automatic lubrication supports consistent cutting, but oil must be filled and checked
  • Proper chain tension (3-6mm lift) helps prevent kickback and premature wear
  • Two-handed control, stable footing, and controlled cutting height improve safety
  • Wood-only intended use supports safer, more accurate results

Notes

  • For setup and first-use guidance, follow the Worx WG303E Electric Chainsaw Manual.
  • Keep handles dry and clean of oil/grease, and maintain the bar rails by cleaning inner grooves and oil passages.
  • Store safely with the machine horizontal so the oil filler cap is uppermost, and empty the tank for long storage.
M: OA-GPT-54-NAN

© Copyright 2026 Manual.ly