Manual.ly Logo

Worx WG303E Manual

0.0 · 0 Ratings

PDF manual · 24 Pages

English

M: OA-GPT-54-NAN
page

/ 24

Loading...
e0222770237ee0088a877b64a5ce2be4e877 page e
Chain Saw WG303E
14
2. CHAIN STOP LEVER (HAND GUARD) (See Fig.
G1)
The Chain Stop Lever (Hand Guard) (5) is a safety
mechanism that causes the Chain (8) to quickly stop. In
many cases when kickback occurs the operator’s hand
strikes the Chain Stop Lever (Hand Guard) causing it
to activate. When activated, the moving Chain quickly
stops.
The following function check should be carried
out at regular intervals. Push the Chain Stop Lever
(hand guard) (5) forwards (position ) and start the chain
saw. The Chain should not move. To deactivate the Chain
Stop Lever, release the On/Off Switch (2) and pull the
Chain Stop Lever (Hand Guard) backwards (position )
(See Fig. G1).
CUTTING
IMPORTANT: Is the oil reservoir filled? Check the
Oil Level Window (19) prior to starting and
regularly during operation. Refill oil when oil level is
low. A full oil tank will last approx. 20 minutes
depending on sawing intensity and stops (See Fig. G2).
Check recent replaced chain tension about every 10
minutes during operation.
1. Connect saw to extension cord. Connect extension
cord to power supply (See Fig. G3).
2. Make sure section of log to be cut is not laying on
the ground. This will keep the chain (8) from touching
the ground as it cuts through the log. Touching the
ground while the Chain is moving is dangerous and
will dull the Chain.
3. Use both hands to grip saw. Always use left hand to
grip front handle and right hand to grip rear handle.
Use a firm grip. Thumbs and fingers must wrap
around saw handles (See Fig. H).
4. Make sure your footing is firm. Keep shoulder width
feet apart. Divide your weight evenly on both feet.
5. When ready to make a cut, push the Lock-off Button
completely in with the right thumb and squeeze the
trigger. This will turn saw on. Releasing the trigger
will turn the saw off. Make sure the saw is running at
full speed before starting a cut.
6. When starting a cut, slowly place moving chain
against the wood. Hold saw firmly in place to avoid
possible bouncing or skating (sideways movement)
of saw.
7. Guide the saw using light pressure and do not put
excessive force on the saw. The motor will overload
and can burn out. It will do the job better and safer at
the rate for which it was intended.
1
1
2
5
G1
19
G2
G3
H

Chat with your Worx WG303E manual using AI

Get instant AI answers from your Worx WG303E manual

Ask anything about the Worx WG303E. Answers come from this manual, with the pages they are based on.

WG303E Maintenance Schedule

Every 10 minutes
Check chain tension

Check recently replaced chain tension about every 10 minutes during operation to ensure proper tightness.

Show in the manual (page 14)
After each use
Clean sawdust from guide bar and sprocket

With unit disconnected from power source, clean all sawdust from the guide bar and sprocket hole after each use.

Show in the manual (page 19)
When removing chain
Clean bar rails

Clean the inner groove of the bar with a wire brush or screwdriver and clear oil passages thoroughly when the chain is removed.

Show in the manual (page 18)
Every 1-3 hours
Clean cover plate and assembly

Remove and brush clean the cover plate, chain and chain bar after 1 to 3 hours of use.

Show in the manual (page 20)
Every time sharpening
Check guide bar condition

Check the condition of the guide bar each time the chain is sharpened to identify wear or damage.

Show in the manual (page 19)
As needed
Lubricate drive sprocket

Inject grease into the lubrication hole until it appears at the outside edge of the sprocket tip using a grease gun.

Show in the manual (page 20)
M: QW-35-FL

Ask a Question

0/1000

Do you recommend WG303E?

Yes No

Frequently Asked Questions

A

Yes. It is intended for sawing trees, tree trunks, branches, wooden beams, and planks. The guidance specifically warns against cutting mineral materials and non-wood building materials, since using the chainsaw outside its intended purpose can create hazardous situations and poor cutting results.

Is this answer helpful?

A

Before use, the saw must be filled with the recommended bar and chain oil; do not run it dry or with an empty tank. To verify the automatic oiler, run the saw and point the guide bar tip toward cardboard or paper on the ground. If an increasing oil pattern appears, the oiler is operating correctly; if not, contact service.

Is this answer helpful?

A

The correct tension is reached when the chain can be raised about 3-6mm from the bar in the center. Recheck often when using a new chain, since it will stretch early. Always unplug before adjusting tension, and ensure the chain rotates freely without kinks.

Is this answer helpful?

A

The chain stop lever (hand guard) is designed to stop the chain quickly when activated, including in some kickback scenarios where the operator hand strikes the lever. The saw should be checked regularly so that, with the hand guard pushed forward and the saw started, the chain does not move.

Is this answer helpful?

A

Use both hands with a firm grip so thumbs and fingers wrap the handles. Do not overreach or cut above shoulder height. Avoid letting the guide bar nose touch anything while the chain is moving. Use the correct replacement bar and chain, keep the chain sharp and properly tensioned, and watch for pinching or wood shifting.

Is this answer helpful?

A

Check for power issues first, then inspect the extension cord and connections. If a fuse is faulty, replace it. If the hand guard safety is not in the correct position, pull it back. If these are fine but problems continue, internal wiring or the switch may be defective and should be handled by a service agent.

Is this answer helpful?

M: OA-GPT-54-NAN

Advantages and Disadvantages

Advantages

  • 2000W corded power for steady cutting of trees, branches, beams, and planks
  • Low-kickback chain and reduced kickback guide bar to lower kickback risk
  • Chain stop lever (hand guard) designed to quickly stop the chain when activated
  • Automatic oiler helps maintain lubrication during operation for better cutting performance
  • Automatic chain tensioning knob with ratchet supports more consistent tension checks
VS

Disadvantages

  • Corded operation requires extension cords and correct voltage/current supply
  • Requires regular oil filling and periodic oil and chain tension inspections
  • Not suitable for cutting mineral materials, plastic, masonry, or non-wood building materials
  • Safety rules limit cutting height and require two-handed operation, reducing flexibility
  • Maintenance is important: bar groove cleaning and sprocket lubrication help prevent wear
M: OA-GPT-54-NAN

Product Specification

Type

Chainsaw

Power

2000W

Bar length

15.75 in

Chain speed

39.37 ft/s

Chain pitch

3/8"

Chain oil tank

6.76 fl oz

Special features

Additional handle, tool-free chain tensioning, automatic chain lubrication, chain brake, chain catch bolt, bumper spike

Weight

10.58 lb

Scope of delivery

Guide bar, saw chain, bar protector

M: GO-GEM-FL-25

Product Description

Worx WG303E Electric Chainsaw

The Worx WG303E Electric Chainsaw is a corded 2000W chainsaw built for confident, everyday cutting of trees, trunks, branches, and wooden beams or planks. With a 400mm bar and a fast 12m/s chain speed, it is designed to help you move from setup to sawing with less hassle, while still emphasizing control and operator safety.

Safety-first design for more controlled cuts

Designed to lower the risk of kickback, the WG303E uses a low-kickback chain and a reduced kickback guide bar. It also includes a chain stop lever (hand guard) that quickly stops the chain when activated, helping protect you in sudden situations. You start it with a lock-off button and on/off switch, and for proper operation the saw should be held with both hands on the handles, keeping your body positioned safely and your cutting height controlled.

Performance and day-to-day operation

The automatic oiler helps keep cutting performance consistent. Before you begin, check the oil level window and refill the 200ml tank as needed. During use, you should periodically inspect chain tension and make sure the chain runs smoothly without kinks, since new chains can stretch during early operation. For best results, aim for correct tension so the chain can be lifted about 3-6mm from the bar in the middle, while still rotating freely.

Practical cutting guidance for real jobs

The saw is intended for wood only, not mineral materials. For cutting logs, safe technique matters: overbuck and underbuck methods help match support conditions, and on slopes you should stand on the uphill side. When working with limbs under tension, proceed with extreme caution because release can cause spring back. For felling, plan an escape route and use correct notching and felling back-cut steps to guide the tree's direction.

Key takeaways (most important results)

  • Low-kickback chain and guide bar reduce, but do not eliminate, kickback risk
  • Automatic lubrication supports consistent cutting, but oil must be filled and checked
  • Proper chain tension (3-6mm lift) helps prevent kickback and premature wear
  • Two-handed control, stable footing, and controlled cutting height improve safety
  • Wood-only intended use supports safer, more accurate results

Notes

  • For setup and first-use guidance, follow the Worx WG303E Electric Chainsaw Manual.
  • Keep handles dry and clean of oil/grease, and maintain the bar rails by cleaning inner grooves and oil passages.
  • Store safely with the machine horizontal so the oil filler cap is uppermost, and empty the tank for long storage.
M: OA-GPT-54-NAN

© Copyright 2026 Manual.ly