Manual.ly Logo

Victron Energy Phoenix Inverter Compact 2000 Manual

0.0 · 0 Ratings

PDF manual · 124 Pages

English

M: QW-35-FL
page

/ 124

Loading...
1518c7212ff738717487f0c29427736c8485 page 11
15
EN NL FR DE ES SE IT Appendix
6. MAINTENANCE
The Compact does not require specific maintenance. It will suffice to check all
connections once a year. Avoid moisture and oil/soot/vapours, and keep the device clean.
7. TROUBLE SHOOTING TABLE
Proceed as follows for quick detection of common faults.
Consult your Victron Energy dealer if the fault cannot be resolved.
Problem
Cause
Solution
The inverter fails
to operate when
switched on.
The battery voltage is too high
or too low.
Ensure that the battery
voltage is within the correct
value.
The inverter fails
to operate
Processor in no function-mode.
Switch Front switch off, wait
4 seconds
Switch front switch on.
The alarm LED
flashes.
Pre-alarm alt. 1: The DC input
voltage is low.
Charge the battery or check
the battery connections.
The alarm LED
flashes
Pre-alarm alt. 2: The ambient
temperature is too high.
Place the inverter in a cool
and well-ventilated room or
reduce the load.
The alarm LED
flashes.
Pre-alarm alt. 3: The load on the
inverter is higher than the
nominal load.
Reduce the load.
The alarm LED
flashes.
Pre-alarm alt. 4: Voltage ripple
on the DC input exceeds
1,25 Vrms.
Check the battery cables
and terminals.
Check the battery capacity;
increase if necessary.
The alarm LED
flashes
intermittantly.
Pre-alarm alt. 5. Low battery
voltage and excessive load.
Charge the batteries, reduce
the load or install batteries
with a higher capacity. Use
shorter and/or thicker
battery cables.
The alarm LED is
on
The inverter did cut out
following a pre-alarm.
Check the table for the
appropriate course of action.

Chat with your Victron Energy Phoenix Inverter Compact 2000 manual using AI

Get instant AI answers from your Victron Energy Phoenix Inverter Compact 2000 manual

Ask anything about the Victron Energy Phoenix Inverter Compact 2000. Answers come from this manual, with the pages they are based on.

Phoenix Inverter Compact 2000 Maintenance Schedule

Remind me when maintenance is due
Yearly
Check all connections

Inspect and verify the tightness of all electrical connections to ensure safe operation.

Show in the manual (page 17)
As needed
Keep device clean and dry

Avoid moisture, oil, soot, and vapors. Keep the device clean to prevent damage.

Show in the manual (page 17)

Free maintenance reminders

Timed to your purchase date. Always free, unsubscribe anytime.

By submitting you agree to the privacy policy. Unsubscribe with one click in any email.
M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend Phoenix Inverter Compact 2000?

Yes No

Frequently Asked Questions

A

The inverter delivers a peak power of 3500 Watts, which allows it to handle high surge currents required by appliances like refrigerators and pumps during startup.

Is this answer helpful?

A

Yes, you can connect up to six identical Phoenix Inverter Compact units in parallel to increase total power output or configure them for three-phase operation.

Is this answer helpful?

A

Enable the Search Mode or AES (Automatic Economy Switch). Search mode reduces consumption by about 70% by shutting down during low load, while AES reduces it by 20%.

Is this answer helpful?

A

Yes, provided it is installed in a dry, well-ventilated area away from direct water exposure and chemicals, adhering to the IP21 protection rating.

Is this answer helpful?

A

Yes, the output frequency can be adjusted between 50 Hz and 60 Hz using DIP switches or configuration software like VEConfigure3.

Is this answer helpful?

A

The inverter will trigger a pre-alarm indicated by a flashing LED. If the voltage remains low, it will shut down to protect the battery from deep discharge.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Superior SinusMax technology provides high start-up power for difficult loads like motors
  • Compact and lightweight design saves valuable installation space
  • Supports parallel connection of up to six units for scalable power
  • Low zero-load power consumption with efficient search mode
  • Fully programmable via DIP switches, VE.Net panel, or PC software
VS

Disadvantages

  • Requires qualified personnel for installation and configuration changes
  • No automatic transfer switch included; requires separate MultiPlus or Quattro unit
  • Maximum continuous power drops significantly at higher ambient temperatures
  • Three-phase operation is limited to wye (Y) configuration only
  • Relay functionality cannot be adjusted using DIP switches alone
M: QW-35-FL

Product Specification

Note

Prices include 0% VAT rates for AT and DE in some cases

Type

Battery inverter, with fan

Protection class

IP21

Ambient temperature

-40°F to +149°F

M: QW-35-FL

Product Description

Victron Energy Phoenix Inverter Compact 2000 Review

The Victron Energy Phoenix Inverter Compact 230V Sinus represents a pinnacle of engineering designed for professional and demanding applications. This device utilizes advanced SinusMax technology to deliver a pure sine wave output, ensuring compatibility with sensitive electronics while maintaining high efficiency. Its compact design and lightweight construction make it ideal for installations where space is at a premium, such as in recreational vehicles, boats, or off-grid cabins.

One of the standout features of this inverter is its exceptional start-up power. Unlike conventional high-frequency inverters, the Phoenix series can handle difficult loads like compressors and electric motors without issue. The unit supports parallel operation, allowing up to six units to be connected for increased power output, or configured for three-phase systems. It also includes a programmable relay that defaults to an alarm function but can be customized for other uses, such as starting a generator set.

Configuration is straightforward, offering flexibility through DIP switches, a VE.Net panel, or PC software. The search mode significantly reduces no-load power consumption, making it energy-efficient during idle periods. With robust safety protections against overload, short circuits, and temperature extremes, the Phoenix Inverter Compact 2000 is built to perform reliably in harsh environments.

Installation Notes

Ensure the unit is mounted in a dry, well-ventilated area with at least 10cm of clearance around it. Always ground the chassis properly to maintain safety class I standards. Use cables with sufficient cross-section to minimize voltage loss and prevent overheating.

M: QW-35-FL

© Copyright 2026 Manual.ly