Manual.ly Logo

Victron Energy Phoenix Inverter Compact 2000 Manual

0.0 · 0 Ratings

PDF manual · 124 Pages

English

M: QW-35-FL
page

/ 124

Loading...
1518c7212ff738717487f0c29427736c8485 page 3
1
EN NL FR DE ES SE IT Appendix
1. SAFETY INSTRUCTIONS
General
Please familiarize yourself with the safety features and instructions by first reading the
documentation supplied with this product before using the equipment. This product has
been designed and tested in accordance with international standards. The equipment
must be used exclusively for the purpose for which it was designed.
WARNING: ELECTRIC SHOCK HAZARD.
The product is used in conjunction with a permanent energy source (battery). Input and/or
output terminals may still be dangerously energized, even when the equipment is
switched off. Always switch off the AC supply and the battery before carrying out
maintenance or servicing the product.
The product has no internal user-serviceable components. Do not remove the front plate
or operate the product if any panels have been removed. All servicing must be undertaken
by qualified personnel.
Never use the product where there is a risk of gas or dust explosions. Consult the battery
manufacturer's information to ascertain that the product is intended for use in conjunction
with the battery. Always comply with the battery manufacturer's safety instructions.
WARNING: Do not lift heavy loads without assistance.
Installation
Read the installation instructions in the installation manual before installing the
equipment.
This is a Safety Class I product (supplied with a protective grounding terminal). The
chassis must be grounded. A grounding point is located on the outside of the product.
Whenever it is likely that the grounding protection has been damaged, the product must
be turned off and secured against unintended operation; please contact qualified service
staff.
Ensure that the DC and AC input cables are fused and fitted with circuit breakers. Never
replace a safety component with a different type. Consult the manual to determine the
correct component.
Before applying power, ensure that the available power source matches the configuration
settings of the product as described in the manual.
Ensure that the equipment is used under the correct ambient conditions. Never operate
the product in a wet or dusty environment. Ensure there is adequate free space for
ventilation around the product and check that the ventilation vents are not blocked.
Ensure that the required system voltage does not exceed the product's capacity.

Chat with your Victron Energy Phoenix Inverter Compact 2000 manual using AI

Get instant AI answers from your Victron Energy Phoenix Inverter Compact 2000 manual

Ask anything about the Victron Energy Phoenix Inverter Compact 2000. Answers come from this manual, with the pages they are based on.

Phoenix Inverter Compact 2000 Maintenance Schedule

Remind me when maintenance is due
Yearly
Check all connections

Inspect and verify the tightness of all electrical connections to ensure safe operation.

Show in the manual (page 17)
As needed
Keep device clean and dry

Avoid moisture, oil, soot, and vapors. Keep the device clean to prevent damage.

Show in the manual (page 17)

Free maintenance reminders

Timed to your purchase date. Always free, unsubscribe anytime.

By submitting you agree to the privacy policy. Unsubscribe with one click in any email.
M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend Phoenix Inverter Compact 2000?

Yes No

Frequently Asked Questions

A

The inverter delivers a peak power of 3500 Watts, which allows it to handle high surge currents required by appliances like refrigerators and pumps during startup.

Is this answer helpful?

A

Yes, you can connect up to six identical Phoenix Inverter Compact units in parallel to increase total power output or configure them for three-phase operation.

Is this answer helpful?

A

Enable the Search Mode or AES (Automatic Economy Switch). Search mode reduces consumption by about 70% by shutting down during low load, while AES reduces it by 20%.

Is this answer helpful?

A

Yes, provided it is installed in a dry, well-ventilated area away from direct water exposure and chemicals, adhering to the IP21 protection rating.

Is this answer helpful?

A

Yes, the output frequency can be adjusted between 50 Hz and 60 Hz using DIP switches or configuration software like VEConfigure3.

Is this answer helpful?

A

The inverter will trigger a pre-alarm indicated by a flashing LED. If the voltage remains low, it will shut down to protect the battery from deep discharge.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Superior SinusMax technology provides high start-up power for difficult loads like motors
  • Compact and lightweight design saves valuable installation space
  • Supports parallel connection of up to six units for scalable power
  • Low zero-load power consumption with efficient search mode
  • Fully programmable via DIP switches, VE.Net panel, or PC software
VS

Disadvantages

  • Requires qualified personnel for installation and configuration changes
  • No automatic transfer switch included; requires separate MultiPlus or Quattro unit
  • Maximum continuous power drops significantly at higher ambient temperatures
  • Three-phase operation is limited to wye (Y) configuration only
  • Relay functionality cannot be adjusted using DIP switches alone
M: QW-35-FL

Product Specification

Note

Prices include 0% VAT rates for AT and DE in some cases

Type

Battery inverter, with fan

Protection class

IP21

Ambient temperature

-40°F to +149°F

M: QW-35-FL

Product Description

Victron Energy Phoenix Inverter Compact 2000 Review

The Victron Energy Phoenix Inverter Compact 230V Sinus represents a pinnacle of engineering designed for professional and demanding applications. This device utilizes advanced SinusMax technology to deliver a pure sine wave output, ensuring compatibility with sensitive electronics while maintaining high efficiency. Its compact design and lightweight construction make it ideal for installations where space is at a premium, such as in recreational vehicles, boats, or off-grid cabins.

One of the standout features of this inverter is its exceptional start-up power. Unlike conventional high-frequency inverters, the Phoenix series can handle difficult loads like compressors and electric motors without issue. The unit supports parallel operation, allowing up to six units to be connected for increased power output, or configured for three-phase systems. It also includes a programmable relay that defaults to an alarm function but can be customized for other uses, such as starting a generator set.

Configuration is straightforward, offering flexibility through DIP switches, a VE.Net panel, or PC software. The search mode significantly reduces no-load power consumption, making it energy-efficient during idle periods. With robust safety protections against overload, short circuits, and temperature extremes, the Phoenix Inverter Compact 2000 is built to perform reliably in harsh environments.

Installation Notes

Ensure the unit is mounted in a dry, well-ventilated area with at least 10cm of clearance around it. Always ground the chassis properly to maintain safety class I standards. Use cables with sufficient cross-section to minimize voltage loss and prevent overheating.

M: QW-35-FL

© Copyright 2026 Manual.ly