Manual.ly Logo

Shark Helmets EvoLine Series 3 Manual

0.0 · 0 Ratings

PDF manual · 106 Pages

English

M: qwen/qwen3.5-flash-20260224
page

/ 106

Loading...
91c7425f2f266e9d7c590e40ba03a9cb19d9 page 16
22
CLEANING
CLEANING THE INTERIOR
The interior textile parts are washable;
it is important to strictly follow the ins-
tructions below to avoid damaging them:
The cheek pads and head section must
be hand washed in warm, soapy water
(about 30°). Do not use aggressive
detergents but either a product for
delicate materials in low dilution
or household soap.
It is essential to dry textile
and foam parts completely
before reinstalling them in
the helmet. They must be
air dried at room tempera-
ture. Never use a clothes
dryer or other heat source.
Never iron textile parts.
For parts with a leather
appearance or textiles
attached to safety ele-
ments, use a slightly damp
sponge or cloth and house-
hold soap and rinse with clean
water. Do not allow too much
water to come into contact with
polystyrene parts.
You must insure that all interior parts
are perfectly dry before using the helmet.
WARNING: Damaged interior padding
will compromise the fit of your helmet
on your head and could allow the helmet to
come off your head in an accident, resulting
in a head injury or death.
THE TEXTILE PARTS
The textile and foam parts providing
comfort to the EvoLine
®
make it easy
for you to appreciate the performance
of your helmet to the full.
The parts in contact with the skin are
made in a fabric that is guaranteed to
feel pleasant, to absorb perspi
-
ration well and to resist wear
satisfactorily.
We treat surfaces to limit the
risk of mould and bacteria.
WARNING: Although
they are selected for
their quality of resistance
and satisfactory wear, all
the comfort padding is
subject to normal wear
and tear. The rate of wear
and tear will depend on
use, care and maintenance,
the length of use and the
degree of acidity of your
perspiration. Wear and tear of
the comfort padding will even-
tually change the fit of your helmet
on your head. If that occurs, you must
immediately replace the helmet or pad-
ding. See your retailer for advice.
WARNING: Each time you put on
your helmet, check the fit as dis-
cussed in “Choose your size“ on page 4.
OwnerManualEvoCarbon.indd 22 24/07/14 16:07

Chat with your Shark Helmets EvoLine Series 3 manual using AI

Get instant AI answers from your Shark Helmets EvoLine Series 3 manual

Ask anything about the Shark Helmets EvoLine Series 3. Answers come from this manual, with the pages they are based on.

EvoLine Series 3 Maintenance Schedule

Remind me when maintenance is due
Every 5 years
Replace helmet

Replace the helmet five years after first purchase even if no damage is visible.

Every use
Inspect for damage and fit

Check helmet every time you use it for evidence of damage, wear, or if it fits snugly.

After any impact
Inspect or replace helmet

If subjected to any impact or dropped, return for inspection or replace immediately.

As needed
Clean interior padding

Hand wash cheek pads and head section in warm soapy water; air dry completely at room temperature.

Show in the manual (page 22)
As needed
Clean visor and sun shield

Soak in tepid water with neutral soap and soft cloth; do not use solvents or alcohol.

Show in the manual (page 18)

Free maintenance reminders

Timed to your purchase date. Always free, unsubscribe anytime.

By submitting you agree to the privacy policy. Unsubscribe with one click in any email.
M: QW-35-FL

Ask a Question

0/1000

Do you recommend EvoLine Series 3?

Yes No

Frequently Asked Questions

A

Press the red button on the chin protection to unlock. Lift the chin section forward until it locks at the back. Always perform this while stationary to ensure safety.

Is this answer helpful?

A

Replace the helmet immediately. Impact damage may not be visible. Continued use compromises safety and structural integrity.

Is this answer helpful?

A

The helmet lasts approximately five years from purchase. Replace it sooner if any impact occurs or if fit becomes loose.

Is this answer helpful?

A

Yes, use mild soap and water. Never use solvents, petroleum, or abrasive pastes as they damage the coating.

Is this answer helpful?

A

No. Never drill, cut, paint, or sticker the helmet. Modifications weaken the structure and eliminate protection.

Is this answer helpful?

A

Remove cheek pads and head liner. Wash with mild soap and warm water by hand. Do not use a dryer. Air dry completely.

Is this answer helpful?

A

Never use the sun shield at night or in poor visibility. Keep it raised. Use only the clear visor for night riding.

Is this answer helpful?

M: qwen/qwen3.5-flash-20260224

Advantages and Disadvantages

Advantages

  • Converts effortlessly between integral and Jet configurations for versatility.
  • High quality polycarbonate visor with anti-scratch and anti-fog treatment.
  • Effective ventilation system to reduce fogging and heat during rides.
VS

Disadvantages

  • Must be replaced after 5 years regardless of visible condition.
  • Replacement required immediately after any impact or drop occurs.
  • Cannot use solvents or paint, limiting customization options significantly.
M: qwen/qwen3.5-flash-20260224

Product Specification

Type

Modular Helmet

Weight

3.97 lbs

M: qwen/qwen3.5-flash-20260224

Product Description

Experience the ultimate versatility on the road with the Shark Evoline series3. Available in various colors and sizes, this modular helmet delivers exceptional performance for riders seeking flexibility. The innovative design allows the rider to switch between an integral full-face configuration and an open face Jet style. This conversion is secure and stable, ensuring aerodynamic integrity in every mode. The chin bar retracts perfectly without causing stability or weight imbalance. Refer to the Shark Evoline series3 (various colors/sizes) Manual for precise operation instructions regarding the conversion mechanism. Protection is a core priority. The helmet features a shell designed to absorb shock impact, utilizing high-quality materials for durability against high and low speed impacts. Safety starts with fit. Riders should measure their head circumference to ensure the helmet fits snugly without gaps. The chin strap system offers advanced locking mechanisms, including the Precise Lock or Double-D ring options. Always test the fit by checking for movement limits when fastened. If the helmet feels too loose, select a smaller size immediately.

Visor quality cannot be overlooked. The integrated visor uses injected polycarbonate to resist scratches and impacts. It offers excellent optical quality labeled Total Vision. Anti-fog and anti-scratch treatments extend visibility and lifespan. An external sun shield button controls the tinted insert for varying light conditions. Never use tinted visors at night or in poor visibility. Proper ventilation channels manage airflow to prevent overheating and fogging. The conversion process is simple. Press the red button on the chin protection to unlock. Lift the chin section forward until it locks at the back. Always perform this while stationary. Never convert while riding. The sun shield should be kept up in tunnels or at night.

The textile parts are washable. Remove cheek pads and head liner for hand washing with warm water. Do not use a dryer. Maintenance requires strict adherence to care instructions. Clean the textile parts with mild soap and water. Never use solvents or petroleum products on the shell or visor. Do not paint or sticker the helmet as this weakens the structure. Replace the helmet after five years or if any impact occurs, even if damage is not visible. Air dry all parts completely before reassembly. This ensures correct fit and safety. This gear combines style and function for modern motorcyclists. Whether commuting or touring, it offers reliable protection. Remember to keep the manual available for future reference regarding fit checks and care procedures. Ensure the sun shield is functional. Always buy genuine replacement parts.

Important Notes:

Check padding wear regularly. Ensure chin strap length is correct. Never drill into the shell. Verify visor locking mechanism before every ride. Protect from heat above 70 degrees Celsius. Do not modify the helmet. Consult official sources for warranty info and safety updates. Keep head measurement records for future size checks.

M: qwen/qwen3.5-flash-20260224

© Copyright 2026 Manual.ly