Manual.ly Logo

Profitec PRO 300 Manual

0.0 · 0 Ratings

PDF manual · 34 Pages

English

M: OA-GPT-5-NAN
page

/ 34

Loading...
f2fe51f5ad73c256151d9c63ae17906bfa55 page 19
ENGLISH
Translation of the original German user manual 24
Fill the ground coffee with the respective grind for espresso into the filter. (The marking inside the filter
basket can help you find the right amount of coffee.)
Compress the ground coffee with the tamper. Clamp the portafilter firmly into the brew group.
Place the cup under the spout of the portafilter (for the preparation of 2 cups, put 1 cup under each spout).
Now activate the coffee switch to start the brewing process. The timer on the PID-display indicates the
brewing time in seconds. In general, the brewing time should be around 20 to 25 seconds. The volume for
a single espresso is about 25 to 30 ml. Place the coffee switch back into the original position once the
desired volume is reached.
The remaining pressure/water will be discharged into the drip tray through the lower part of the brew
group.
• Only freshly ground coffee allows for an optimal coffee result. Therefore, use a
professional coffee grinder.
• We recommend to use our stainless steel tamper with a diameter of 58 mm for
optimum tamping.
6.4 Dispensing of hot water
1 In case you have not done so yet, activate the steam boiler. Wait until the boiler pressure gauge
indicates a pressure of 1.0
1.3 bars.
2 Place a suitable container (with heat-insulated grip) underneath the hot water wand. Now you can
dispense hot water (e.g. for tea) by turning the hot water knob. When dispensing large amounts of
water, it is advisable to turn the machine off so that no cold water is pumped out of the fresh water
tank.
3 After having dispensed hot water, turn the machine back on. The boiler is automatically refilled with
fresh water.
Please close the hotwater-/steam valve gently and do not over tighten it.
When the machine is switched off, more hot water can be dispensed.
However, one does not necessarily have to switch off the machine for dispensing hot
water.
Caution!
Place the hot water wand into the water container in order to avoid injuries due to hot
water spraying.
6.5 Dispensing of steam
The PRO 300 makes it possible to generate large amounts of steam in order to heat or froth beverages,
e. g. milk or punch. It is a professional and compact espresso coffee machine. Within a few seconds, you
can prepare milk froth. Please pay attention to the instructions below. Do not bring the milk to a boil,
otherwise frothing milk will not be possible.
1 In case you have not yet done so , activate the steam boiler by the steam switch. The orange signal
lamp comes on. Wait a short time until steam has built up in the boiler. The boiler pressure gauge
should indicate a pressure of 1.0
1.3 bars.
2
Important: In order to get the best results when frothing milk, open the steamknob for approx.
5 seconds to release the condensation water in the pipe. This also prevents milk from being sucked
into the boiler.
3 Immerse the steam nozzle into the liquid.
4 Turn the steamknob.
5 Heat and/or froth the liquid.
6 After frothing or heating, release the steam into the drip tray to keep the holes of the steam nozzle
clean.
Risk of injury
Always keep the steam nozzle underneath the surface of the liquid while heating or
frothing in order to avoid splashing.

Chat with your Profitec PRO 300 manual using AI

Get instant AI answers from your Profitec PRO 300 manual

Ask anything about the Profitec PRO 300. Answers come from this manual, with the pages they are based on.

PRO 300 Maintenance Schedule

Remind me when maintenance is due
Daily
Clean portafilter and drip tray

Clean the portafilter, filters, water tank, drip tray, and tamper daily with warm water and food-safe detergent.

Show in the manual (page 25)
Monthly
Empty the steam boiler

Empty the water from the steam and hot water boiler every one to two weeks to ensure fresh water is present.

Show in the manual (page 25)
Every 90-140 brews
Clean the brew group

Use a cleaning tablet with the blind filter to clean and degrease the brew group after about 90 to 140 brewing cycles.

Show in the manual (page 26)
After each use
Clean steam wand

Clean the steam wand and hot water wand after every use with a damp cloth to remove liquid residues.

Show in the manual (page 25)

Free maintenance reminders

Timed to your purchase date. Always free, unsubscribe anytime.

By submitting you agree to the privacy policy. Unsubscribe with one click in any email.
M: QW-35-FL

Ask a Question

0/1000

Do you recommend PRO 300?

Yes No

Frequently Asked Questions

A

The PID regulates and displays the coffee boiler temperature, allowing you to set and store a precise extraction temperature (factory set to 93 °C). It supports temperature adjustments and toggling between °C and °F for consistent brewing results.

Is this answer helpful?

A

With a container under the brew group, raise the coffee switch for at least 30 seconds. The display shows Fill and will clear after the boiler has been filled. Refill the water tank if needed and wait until the PID reaches the set temperature.

Is this answer helpful?

A

Program a CLn reminder (0–200 shots) or clean approximately every 90–140 shots. Use the blind filter and a group cleaner tablet: run the coffee switch in 20-second intervals until clear water runs, then rinse and repeat per instructions.

Is this answer helpful?

A

Use soft potable water up to 4° dH or install a water filter. Hard water causes limescale that can damage the boiler and internal tubing; severe scaling requires professional descaling and may need partial disassembly.

Is this answer helpful?

A

Activate the steam boiler, wait for 1.0–1.3 bar, open the steam valve briefly to purge condensate, then position the wand just below the milk surface. Keep the wand submerged while creating a gentle vortex, stop before milk exceeds ~77 °C to preserve foam quality.

Is this answer helpful?

A

ECO mode sets an automatic shutdown timer (0–600 minutes, default 90). Program it via the PID menu in 30-minute steps; after the last extraction the countdown runs in the background and powers down the machine when elapsed.

Is this answer helpful?

A

Daily cleaning (portafilter, drip tray, steam wand), periodic backflushing and replacing the group gasket or cleaning the steam nozzle are user-serviceable. Descaling with heavy scale, boiler disassembly, or electrical repairs should be done by authorized service personnel.

Is this answer helpful?

M: OA-GPT-5-NAN

Advantages and Disadvantages

Advantages

  • PID temperature control for accurate, adjustable extraction temperatures.
  • Dual-boiler design with separate steam boiler for stable steam performance.
  • Programmable features: ECO auto-shutdown, CLn cleaning reminder, and display options.
  • Solid build and serviceable components (replaceable group gasket, shower screen).
  • Complete accessories included: single/double baskets, blind filter, tamper and brush.
VS

Disadvantages

  • Not intended for heavy commercial use; designed for home and light professional settings.
  • Requires soft water (≤4° dH) or filtration to avoid limescale and potential technician descaling.
  • Some maintenance tasks (descaling, gasket replacement) may require qualified service.
  • Portafilter, drip tray and water tank are not dishwasher-safe, increasing manual cleaning.
  • No external adjustment for steam boiler pressure; steam regulated internally by a pressostat.
M: OA-GPT-5-NAN

Product Specification

Construction Type

Dual Boiler

Power

2200W

Color

stainless steel

Coffee System

Ground Coffee

Water Tank Capacity

0.74 gal

Special Features

2-Cup Function, Hot Water/Steam Nozzle, Boiler Pressure Gauge, Heated Cup Tray

Dimensions

10.04x15.16x18.70in (WxHxD)

Weight

39.68lb

M: OA-GPT-54-NAN

Product Description

Profitec Pro 300 — Profitec Pro 300 Manual

The Profitec Pro 300 is a compact, prosumer espresso machine designed for home and light commercial-style use. Built around a PID-controlled coffee boiler and a separate steam boiler, the Pro 300 offers stable extraction temperatures, fast heat-up times and professional features such as a pressure gauge, removable 2.8 L water tank, and a robust brass brew group. Its PID temperature control allows fine adjustment of extraction temperature, while the steam boiler (regulated by a pressure switch) reliably delivers powerful steam for milk texturing.

Ergonomic controls and clear indicators make operation intuitive: dedicated switches for coffee and steam, a PID display with programmability (temperature setpoint, Celsius/Fahrenheit display, ECO auto-shutdown and CLn cleaning reminder), and a simple Fill mode for initial boiler priming. The machine ships with single- and double-spout portafilters, single- and double-shot baskets, a blind filter for backflushing, tamper, cleaning brush, and a silicone tube for optional water filtration.

In practice the Pro 300 excels when paired with freshly ground beans and a consistent tamp. The PID lets you dial in extraction temperature (factory 93 °C) to suit different blends; the CLn counter reminds you to perform group cleaning after a programmable number of shots. Daily maintenance is straightforward: rinse portafilter parts, empty and clean drip tray, and wipe steam wand after every use. Periodic group backflushing with a detergent tablet and occasional replacement of the group gasket and shower screen keep performance consistent.

Safety and longevity are emphasized: use soft water (max 4° dH) or a water filter to avoid scale buildup, never operate the machine without water, and have electrical installation and repairs handled by qualified technicians. The machine complies with CE directives and WEEE registration for disposal.

Whether you’re exploring temperature profiling via PID or need reliable steam for milk microfoam, the Profitec Pro 300 combines solid build quality, serviceable internals, and programmable convenience for home baristas seeking café-level results.

Notes

  • Use soft, potable water (≤4° dH) or a water softener to prevent scale. Regular descaling by an authorized technician is recommended if required.
  • The ECO mode can auto-shutdown between 0–600 minutes (factory 90 min) to save energy.
  • Always vent the steam wand briefly before frothing to remove condensate and avoid drawing milk into the boiler.
  • Replace group gasket and shower screen as part of maintenance; backflushing is recommended every 90–140 shots.
M: OA-GPT-5-NAN

© Copyright 2026 Manual.ly