Manual.ly Logo

Profitec PRO 300 Manual

0.0 · 0 Ratings

PDF manual · 34 Pages

English

M: OA-GPT-5-NAN
page

/ 34

Loading...
f2fe51f5ad73c256151d9c63ae17906bfa55 page 13
ENGLISH
Translation of the original German user manual 18
1 INCLUDED WITH DELIVERY
1 portafilter 1 spout
1 portafilter 2 spouts
1 filter 1 cup
1 filter 2 cups
1 blind filter
1 cleaning brush
1 tamper
1 silicone tube for water filter
1 instruction manual
2 GENERAL ADVICE
2.1 General safety notes
• Make sure that the local main supply voltage corresponds to the information given on the
type plate on the front panel of the espresso machine.
• The installation of the machine should be carried out by authorised specialists according
to the instructions in chapter 4.
• Plug the machine into a grounded socket only and do not leave it unattended.
• Make sure the machine is disconnected from the power supply during service and when
replacing parts.
• Do not roll or bend the power cord.
•
If the supply cord is damaged, it must be replaced by a service agent or similarly
qualified persons, in order to avoid a hazard.
• Do not use an extension cord/ do not use a multiple socket.
•
Place the machine on an even and stable surface. Only use the machine on a water
resistant surface.
• Never place the machine on hot surfaces.
• Never submerse the machine in water; do not operate the machine with wet hands.
• Make sure that no liquid gets on the power plug of the machine or on the socket.
• The machine should only be used by experienced adult persons.
• The machine is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• Do not expose the machine to inclement weather (frost, snow, rain) and do not use it
outdoors.
• Keep the packing out of reach of children.
• Only use original spare parts.
• Do not operate the machine with carbonated water, but with soft, potable water.
• Do not operate the machine without water.
• Please note that the surface of the machine, in particular the brew group and the steam
wand, become hot during operation and there is a risk of injury.
If you have any further questions or if you require any further information, please contact your
specialised dealer before starting up the espresso coffee machine.
Our machines comply with the relevant safety regulations.
Any repairs or changes of components must be carried out by an authorised specialty dealer. In case of
non-observance the manufacturer does not assume liability and is not liable to recourse.
Authorised service points outside Europe can be found on our dealer search: www.profitec-espresso.com
or can be requested from us.
Important
You should use water with a hardness of max. 4° dH in order to protect your machine from
lime scale damage. When necessary, make use of a water softener in order to reach an
adequate hardness level.
Contact your specialised dealer before undertaking this measure.
An already calcified machine may only be descaled by your specialised dealer because a
partial disassembly of the boiler and the tubing will be necessary to prevent the system from
being blocked by lime residues.
A late descaling can cause substantial damage to the machine.

Chat with your Profitec PRO 300 manual using AI

Get instant AI answers from your Profitec PRO 300 manual

Ask anything about the Profitec PRO 300. Answers come from this manual, with the pages they are based on.

PRO 300 Maintenance Schedule

Remind me when maintenance is due
Daily
Clean portafilter and drip tray

Clean the portafilter, filters, water tank, drip tray, and tamper daily with warm water and food-safe detergent.

Show in the manual (page 25)
Monthly
Empty the steam boiler

Empty the water from the steam and hot water boiler every one to two weeks to ensure fresh water is present.

Show in the manual (page 25)
Every 90-140 brews
Clean the brew group

Use a cleaning tablet with the blind filter to clean and degrease the brew group after about 90 to 140 brewing cycles.

Show in the manual (page 26)
After each use
Clean steam wand

Clean the steam wand and hot water wand after every use with a damp cloth to remove liquid residues.

Show in the manual (page 25)

Free maintenance reminders

Timed to your purchase date. Always free, unsubscribe anytime.

By submitting you agree to the privacy policy. Unsubscribe with one click in any email.
M: QW-35-FL

Ask a Question

0/1000

Do you recommend PRO 300?

Yes No

Frequently Asked Questions

A

The PID regulates and displays the coffee boiler temperature, allowing you to set and store a precise extraction temperature (factory set to 93 °C). It supports temperature adjustments and toggling between °C and °F for consistent brewing results.

Is this answer helpful?

A

With a container under the brew group, raise the coffee switch for at least 30 seconds. The display shows Fill and will clear after the boiler has been filled. Refill the water tank if needed and wait until the PID reaches the set temperature.

Is this answer helpful?

A

Program a CLn reminder (0–200 shots) or clean approximately every 90–140 shots. Use the blind filter and a group cleaner tablet: run the coffee switch in 20-second intervals until clear water runs, then rinse and repeat per instructions.

Is this answer helpful?

A

Use soft potable water up to 4° dH or install a water filter. Hard water causes limescale that can damage the boiler and internal tubing; severe scaling requires professional descaling and may need partial disassembly.

Is this answer helpful?

A

Activate the steam boiler, wait for 1.0–1.3 bar, open the steam valve briefly to purge condensate, then position the wand just below the milk surface. Keep the wand submerged while creating a gentle vortex, stop before milk exceeds ~77 °C to preserve foam quality.

Is this answer helpful?

A

ECO mode sets an automatic shutdown timer (0–600 minutes, default 90). Program it via the PID menu in 30-minute steps; after the last extraction the countdown runs in the background and powers down the machine when elapsed.

Is this answer helpful?

A

Daily cleaning (portafilter, drip tray, steam wand), periodic backflushing and replacing the group gasket or cleaning the steam nozzle are user-serviceable. Descaling with heavy scale, boiler disassembly, or electrical repairs should be done by authorized service personnel.

Is this answer helpful?

M: OA-GPT-5-NAN

Advantages and Disadvantages

Advantages

  • PID temperature control for accurate, adjustable extraction temperatures.
  • Dual-boiler design with separate steam boiler for stable steam performance.
  • Programmable features: ECO auto-shutdown, CLn cleaning reminder, and display options.
  • Solid build and serviceable components (replaceable group gasket, shower screen).
  • Complete accessories included: single/double baskets, blind filter, tamper and brush.
VS

Disadvantages

  • Not intended for heavy commercial use; designed for home and light professional settings.
  • Requires soft water (≤4° dH) or filtration to avoid limescale and potential technician descaling.
  • Some maintenance tasks (descaling, gasket replacement) may require qualified service.
  • Portafilter, drip tray and water tank are not dishwasher-safe, increasing manual cleaning.
  • No external adjustment for steam boiler pressure; steam regulated internally by a pressostat.
M: OA-GPT-5-NAN

Product Specification

Construction Type

Dual Boiler

Power

2200W

Color

stainless steel

Coffee System

Ground Coffee

Water Tank Capacity

0.74 gal

Special Features

2-Cup Function, Hot Water/Steam Nozzle, Boiler Pressure Gauge, Heated Cup Tray

Dimensions

10.04x15.16x18.70in (WxHxD)

Weight

39.68lb

M: OA-GPT-54-NAN

Product Description

Profitec Pro 300 — Profitec Pro 300 Manual

The Profitec Pro 300 is a compact, prosumer espresso machine designed for home and light commercial-style use. Built around a PID-controlled coffee boiler and a separate steam boiler, the Pro 300 offers stable extraction temperatures, fast heat-up times and professional features such as a pressure gauge, removable 2.8 L water tank, and a robust brass brew group. Its PID temperature control allows fine adjustment of extraction temperature, while the steam boiler (regulated by a pressure switch) reliably delivers powerful steam for milk texturing.

Ergonomic controls and clear indicators make operation intuitive: dedicated switches for coffee and steam, a PID display with programmability (temperature setpoint, Celsius/Fahrenheit display, ECO auto-shutdown and CLn cleaning reminder), and a simple Fill mode for initial boiler priming. The machine ships with single- and double-spout portafilters, single- and double-shot baskets, a blind filter for backflushing, tamper, cleaning brush, and a silicone tube for optional water filtration.

In practice the Pro 300 excels when paired with freshly ground beans and a consistent tamp. The PID lets you dial in extraction temperature (factory 93 °C) to suit different blends; the CLn counter reminds you to perform group cleaning after a programmable number of shots. Daily maintenance is straightforward: rinse portafilter parts, empty and clean drip tray, and wipe steam wand after every use. Periodic group backflushing with a detergent tablet and occasional replacement of the group gasket and shower screen keep performance consistent.

Safety and longevity are emphasized: use soft water (max 4° dH) or a water filter to avoid scale buildup, never operate the machine without water, and have electrical installation and repairs handled by qualified technicians. The machine complies with CE directives and WEEE registration for disposal.

Whether you’re exploring temperature profiling via PID or need reliable steam for milk microfoam, the Profitec Pro 300 combines solid build quality, serviceable internals, and programmable convenience for home baristas seeking café-level results.

Notes

  • Use soft, potable water (≤4° dH) or a water softener to prevent scale. Regular descaling by an authorized technician is recommended if required.
  • The ECO mode can auto-shutdown between 0–600 minutes (factory 90 min) to save energy.
  • Always vent the steam wand briefly before frothing to remove condensate and avoid drawing milk into the boiler.
  • Replace group gasket and shower screen as part of maintenance; backflushing is recommended every 90–140 shots.
M: OA-GPT-5-NAN

© Copyright 2026 Manual.ly