Manual.ly Logo

PeakTech 1265 Manual

0.0 · 0 Ratings

PDF manual · 170 Pages

English

M: OA-GPT-54-NAN
page

/ 170

Loading...
fd9755b53f2cdae95cdecf64f30a94cf94f2 page 59
1. Safety Precautions
This product complies with the requirements of the following European Community Directives: 2004/108/EG
(Electromagnetic Compatibility) and 2006/95/EG (Low Voltage) as amended by 2004/22/EG (CE-Marking).
Overvoltage category II; pollution degree 2.
To ensure safe operation of the equipment and eliminate the danger of serious injury due to short-circuits
(arcing), the following safety precautions must be observed. Damages resulting from failure to observe these
safety precautions are exempt from any legal claims whatever.
* Do not use this instrument for high-energy industrial installation measurement.
* Do not place the equipment on damp or wet surfaces.
* Do not exceed the maximum permissible input ratings (danger of serious injury and/or destruction of the
equipment).
* The meter is designed to withstand the stated max voltages. If it is not possible to exclude without that
impulses, transients, disturbance or for other reasons, these voltages are exceeded a suitable presale
(10:1) must be used.
* Disconnect test leads or probe from the measuring circuit before switching modes or functions.
* Check test leads and probes for faulty insulation or bare wires before connection to the equipment.
* To avoid electric shock, do not operate this product in wet or damp conditions.
* Conduct measuring works only in dry clothing and rubber shoes, i. e. on isolating mats.
* Never touch the tips of the test leads or probe.
* Comply with the warning labels and other info on the equipment.
* The measurement instrument is not to be to operated unattended.
* Do not subject the equipment to direct sunlight or extreme temperatures, humidity or dampness.
* Do not subject the equipment to shocks or strong vibrations.
* Do not operate the equipment near strong magnetic fields (motors, transformers etc.).
* Keep hot soldering irons or guns away from the equipment.
* Allow the equipment to stabilize at room temperature before taking up measurement (important for exact
measurements).
* Do not input values over the maximum range of each measurement to avoid damages of the
instrument.
* Periodically wipe the cabinet with a damp cloth and mid detergent. Do not use abrasives or solvents.
* The meter is suitable for indoor use only
* Warning:
To avoid fire or electrical shock, when the oscilloscope input signal connected is more than 42V peak
(30Vrms) or on circuits of more than 4800VA, please take note of below items:
- Only use accessory insulated voltage probes and test lead.
- Check the accessories such as probe before use and replace it if there are any damages.
- Remove probes, test leads and other accessories immediately after use.
- Remove USB cable which connects oscilloscope and computer.
- Do not apply input voltages above the rating of the instrument because the probe tip voltage will directly
transmit to the oscilloscope. Use with caution when the probe is set as 1:1.
- Do not use exposed metal BNC or banana plug connectors.
- Do not insert metal objects into connectors.
-88-

Chat with your PeakTech 1265 manual using AI

Get instant AI answers from your PeakTech 1265 manual

Ask anything about the PeakTech 1265. Answers come from this manual, with the pages they are based on.

1265 Maintenance Schedule

Remind me when maintenance is due
Yearly
Calibration adjustment

One year is recommended for the calibration interval period to ensure accuracy.

Show in the manual (page 168)
Regularly
Inspect probe and instrument

Check the condition of the probe and instrument regularly according to their operating state.

Show in the manual (page 168)
Regularly
Clean external surfaces

Wipe dust with a soft cloth and clean with a damp soft cloth using mild detergent or water. Ensure device is dry before use.

Show in the manual (page 168)

Free maintenance reminders

Timed to your purchase date. Always free, unsubscribe anytime.

By submitting you agree to the privacy policy. Unsubscribe with one click in any email.
M: QW-35-FL

Ask a Question

0/1000

Do you recommend 1265?

Yes No

Frequently Asked Questions

A

It is designed for viewing, measuring, and analyzing electrical signals in labs, repair shops, classrooms, and general electronics troubleshooting. It helps users inspect waveforms, triggers, and signal quality quickly.

Is this answer helpful?

A

Autoscale, clear menu navigation, and the large TFT display simplify setup and signal reading. These features help beginners get a stable waveform without spending too much time adjusting settings manually.

Is this answer helpful?

A

Yes. The built-in FFT function converts time-domain signals into frequency content, which is useful for checking harmonics, noise, and oscillator behavior.

Is this answer helpful?

A

Yes. It can save waveforms, settings, and screen images. USB storage is especially useful for exporting screenshots and sharing results with others.

Is this answer helpful?

A

Proper probe compensation improves measurement accuracy and waveform shape. If the probe is not adjusted correctly, readings can become distorted or misleading.

Is this answer helpful?

A

No. The device should not be used in high-energy circuits, and input limits must always be respected. Using the right probe and safe setup is essential for protection and accurate results.

Is this answer helpful?

M: OA-GPT-54-NAN

Advantages and Disadvantages

Advantages

  • 30 MHz bandwidth and 250 MSa/s sampling suit many general electronics tasks.
  • 8-inch TFT display makes waveforms, triggers, and measurements easy to read.
  • FFT, Pass/Fail, and waveform playback add strong analysis capability.
  • USB and LAN connectivity support data transfer and computer integration.
VS

Disadvantages

  • 1X probe mode reduces bandwidth, limiting full performance.
  • Advanced menus and trigger options may take time to learn.
  • Not designed for high-energy circuits or harsh outdoor conditions.
  • Some functions are more useful on higher-series models in the PeakTech range.
M: OA-GPT-54-NAN

Product Description

PeakTech 1265 Digital Oscilloscope: Smart Tools for Fast Signal Analysis

The PeakTech 1265 Digital Oscilloscope is a compact and capable choice for electronics work, repair tasks, and training environments where clear signal visibility matters. Built for everyday troubleshooting, it combines a 30 MHz bandwidth, 250 MSa/s sampling rate, and a 10 k-point record length per channel to capture common waveforms with confidence. For users who want a practical bench instrument rather than a complicated lab system, it strikes a useful balance between performance and ease of use.

One of the strongest qualities of the PeakTech 1265 is its straightforward workflow. The Autoscale and Autoset functions help bring unknown signals into view quickly, while the 8-inch TFT display gives a sharp and readable overview of waveforms, measurements, and trigger status. That makes it easier to inspect periodic signals, check pulse shapes, and identify noise or distortion without wasting time on manual setup.

The oscilloscope also supports useful analysis features that go beyond basic viewing. FFT analysis helps reveal frequency content, Pass/Fail testing supports repetitive quality checks, and waveform recording with playback makes it easier to study signal changes over time. With USB and LAN connectivity, the device can also fit into a modern test setup, whether you need to transfer data, save screenshots, or integrate the instrument with a computer-based workflow.

For hands-on users, the manual emphasizes careful setup and reliable measurement habits. Probe compensation, correct attenuation settings, and self-calibration are important steps for accurate results. Those details matter, especially when working with mixed signals, adjustable time bases, or sensitive circuit points. The built-in help system and multilingual interface add even more convenience for students and technicians who want to learn quickly.

Overall, the PeakTech 1265 Digital Oscilloscope is a strong everyday instrument for signal diagnostics, component testing, and classroom demonstrations. It is especially appealing for users who value simple control, practical measurement functions, and a clear display in a durable bench-top format.

Notes

  • Use a 10X probe setting to get the best bandwidth and reliable readings.
  • Perform self-calibration after major temperature changes for better accuracy.
  • Avoid exceeding the input limits to protect both the instrument and the user.
  • USB and LAN features make saving and sharing results easier.
M: OA-GPT-54-NAN

© Copyright 2026 Manual.ly