Manual.ly Logo

Oase ProMax ClearDrain 6000 Manual

0.0 · 0 Ratings

PDF manual · 157 Pages

English

M: QW-35-FL
page

/ 157

Loading...
4952e998c36eb35a5ca7701b96287d853cc0 page e
14 ProMax ClearDrain 6000
Manual mode
The pump remains permanently switched
on if the float switch is set vertically and
the cable points downward.
NOTE
The pump can run dry in manual mode.
• Switch off the pump when the minimum
water level is reached.
• Running the pump dry increases wear.
D
• Move the handle into the horizontal po-
sition and push the cable directly at the
transition to the float switch into the ca-
ble clip such that the float switch is in a
vertical position.
Installing the pump
E
• Install the pump in a horizontal and sta-
ble position in the water.
• If it needs to be lowered into a well or a
shaft, fasten a rope to the handle. Do
not carry it by the power connection
cable.
• Install the pump such that it does not
take in dirt particles with a size >5 mm,
which would block the intake. Install the
pump in a raised position if necessary.
• Ensure that the float switch can always
move freely.
OPERATION
WARNING
Dangerous electrical voltage!
Death or severe injury from electrocu-
tion.
• Only connect the pump to the power
supply when there are no persons in or
reaching into the water.
• Before stepping into or reaching into the
water, switch off all units located in the
water.
NOTE
Do not use the unit for long-term opera-
tion. Otherwise this will impair the operat-
ing life of the unit accordingly.
Switching on the unit
• Insert the power plug into the socket.
– The pump is ready for operation.
– The pump will start up as soon as the
level of the water reaches the switch-
on height.
Switching off the unit
• Disconnect the power plug.
– When the pump is switched off, resid-
ual water in the hose may flow back
and out of the pump intake.
NOTE
Rinse out the pump with clean water after
use.

Chat with your Oase ProMax ClearDrain 6000 manual using AI

Get instant AI answers from your Oase ProMax ClearDrain 6000 manual

Ask anything about the Oase ProMax ClearDrain 6000. Answers come from this manual, with the pages they are based on.

ProMax ClearDrain 6000 Maintenance Schedule

Remind me when maintenance is due
Semiannual
Clean the pump unit

Clean the unit as required but at least twice per year. Use PumpClean or vinegar/chlorine-free agents for limescale. Rinse thoroughly with clean water.

Show in the manual (page 15)
Yearly (Seasonal)
Store unit frost-free before winter

If frost is expected, drain hoses and pipes, clean the unit, check for damage, and store it in a dry, frost-free place.

Show in the manual (page 16)
After each use
Rinse the pump after use

Rinse out the pump with clean water after every use to prevent clogging and residue buildup.

Show in the manual (page 14)

Free maintenance reminders

Timed to your purchase date. Always free, unsubscribe anytime.

By submitting you agree to the privacy policy. Unsubscribe with one click in any email.
M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend ProMax ClearDrain 6000?

Yes No

Frequently Asked Questions

A

The Oase ProMax ClearDrain 6000 is designed to pump water containing solid particles with a maximum grain size of 5 millimeters.

Is this answer helpful?

A

No, this pump is not intended for long-term operation such as continuous water circulation in a pond. It is best suited for draining or intermittent use.

Is this answer helpful?

A

No, the connection cable cannot be replaced. If the cable is damaged, the entire unit must be disposed of and replaced for safety reasons.

Is this answer helpful?

A

It is recommended to clean the pump as needed, but at least twice a year, using non-aggressive cleaning agents like vinegar-based solutions or specialized pump cleaners.

Is this answer helpful?

A

The pump has a maximum immersion depth of 7 meters, making it suitable for deep wells or large containers.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • High flow rate of 6000 liters per hour for rapid drainage
  • Automatic float switch simplifies operation without manual intervention
  • Can handle water with solid particles up to 5 mm in diameter
  • Adjustable handle allows for versatile installation angles
  • IPX8 protection rating ensures safe operation under deep immersion
VS

Disadvantages

  • Not suitable for saltwater or drinking water applications
  • Cannot be used for continuous long-term pond recirculation
  • Damaged power cable cannot be replaced and requires disposal of the unit
  • Impeller is a wear part requiring professional service for replacement
  • Manual mode carries a risk of dry running if not monitored closely
M: QW-35-FL

Product Specification

Power

220W

Flow rate

1585.03 gph

Head height

19.69 ft

Submersion depth

22.97 ft

Pressure

8.7 psi

Pressure connection

1 1/4"

Features

without tank, IPX8

Cable length

32.81 ft

Weight

10.58 lbs

M: QW-35-FL

Product Description

Discover the Power of the Oase ProMax ClearDrain 6000

The Oase ProMax ClearDrain 6000 Electric Clear Water Submersible Pump is a robust solution designed for efficient water management in residential and light commercial settings. This submersible pump excels at moving clear water, rainwater, or water containing small particles up to 5 mm in size. Whether you need to drain basins, irrigate gardens, empty cisterns, or extract water from wells, this unit delivers reliable performance with a maximum flow rate of 6000 liters per hour.

Designed with user safety and ease of use in mind, the pump features an adjustable handle that allows for flexible positioning. The integrated float switch enables automatic operation, turning the pump on when water levels rise and off when they drop. For specific tasks requiring constant drainage, a manual mode is available, though users must be cautious to prevent dry running. The device is built with an IPX8 protection rating, ensuring it can withstand immersion depths of up to 7 meters.

Installation is straightforward thanks to the stepped hose adapter which accommodates various hose diameters, ensuring optimal flow rates. However, the pump is strictly intended for clear water applications and should never be used with saltwater, drinking water, or dirty waste water. It is also not suitable for continuous long-term circulation in ponds. Regular maintenance, including cleaning twice a year, is recommended to extend the lifespan of the impeller and other components. Always ensure the power supply matches the technical data found on the type plate before connecting the unit.

M: QW-35-FL

© Copyright 2026 Manual.ly