Manual.ly Logo

Oase BioMaster Thermo Manual

0.0 · 0 Ratings

PDF manual · 188 Pages

English

M: QW-35-FL
page

/ 188

Loading...
15da36686aa6a7f97f3731ca72ac2b86df39 page 18
- EN -
24 BioMaster 250/350/600, BioMaster Thermo 250/350/600
REMEDY OF FAULTS
S
Malfunction
Cause
Remedy
Unit does not start up.
No mains voltage
Check the mains voltage.
Impeller unit blocked
Clean
Air in the filter
Vent the filter. Move the filter from side to
side, if necessary, to allow the remaining air
to escape.
Water flow insufficient
Impeller unit soiled
Clean
Impeller unit worn
Replace the impeller unit.
The flow is not correctly set.
Correct the setting.
Foam filter of the pre-filter soiled
Clean
Filter media in the container soiled
Clean
Suction basket clogged
Clean
Pipework soiled
Clean suction unit, flow-out unit and hoses.
Insufficient filtering performance
Foam filter of the pre-filter soiled
Clean
Foam filter of the pre-filter worn
Replace
Filter media in the container soiled
Clean
Filter media in the container worn
Replace
Insufficient water heating
(only units with heater)
Heater defective
Replace
Heater not calibrated
Calibrate
Water temperature incorrectly set on the
heater
Correct the water temperature setting on
the heater.
Water flow insufficient
See malfunction "Water flow insufficient"
The filter cannot be vented.
Valve box in the pre-filter blocked
Clean the valve box.
Filter is not below the surface of the water.
Install the filter below the surface of the
water.
Increased noise
Air in the filter
Move the filter from side to side to allow
the remaining air to escape.
MAINTENANCE AND CLEANING
• If necessary, clean with clear water using a soft
brush.
• Do not use cleaning agents or chemical solutions.
We recommend using OASE PumpClean for remov-
ing calcium deposits.
• Cleaning and replacement cycles for filter media are
dependent on the size of the aquarium and the
number of fish. Therefore, it is necessary to clean
and replace the filter media as required to ensure
optimum filter performance.
• If there are several foam filters: Clean or replace the
foam filters at different times. This saves enough
useful bacteria to ensure good biological filtration
of the water.
NOTE
Thoroughly rinse out all filter material with warm tap
water before using for the first time in order to remove
any soiling. (→ Cleaning/replacing the filter media)
Cleaning and maintenance work:
Area
Tasks to be carried out
Foam filter, pre-filter
(→ Cleaning/replacing the foam fil-
ter of the pre-filter)
Filter media, contai-
ner
(→ Cleaning/replacing the filter me-
dia)
Heater
HeatUp 25/50/75/
100/150/200/250/300
Impeller unit, pump
casing
(→ Cleaning/replacing the impeller
unit)
Valve box, pre-filter
(→ Cleaning the valve box of the pre-
filter)
Suction chamber, pre-
filter
(→ Cleaning the suction chamber of
the pre-filter)
NOTE
The cycle for cleaning the foam filter in the pre-filter is
longer if a coarser foam filter is used.

Chat with your Oase BioMaster Thermo manual using AI

Get instant AI answers from your Oase BioMaster Thermo manual

Ask anything about the Oase BioMaster Thermo. Answers come from this manual, with the pages they are based on.

BioMaster Thermo Maintenance Schedule

Regularly
Check water level and circulation

Regularly check the water level and circulation in the filter and in the aquarium to ensure the pump does not run dry.

Show in the manual (page 23)
As required
Clean or replace pre-filter foam

Rinse foam filters in warm water. Replace if worn. Frequency depends on tank size and fish load. Clean at different times to preserve bacteria.

Show in the manual (page 24)
As required
Clean or replace main filter media

Flush filter media with aquarium water. Replace if necessary. Rinse new media with warm tap water before first use.

Show in the manual (page 24)
As required
Clean impeller unit and pump casing

Remove the impeller unit from the pump head, clean it, and reassemble. Replace if worn to maintain flow rate.

Show in the manual (page 24)
If venting fails
Clean pre-filter valve box

Clean the valve box only if venting does not work after cleaning the pre-filter foams. Remove seal and flaps to clean all parts.

Show in the manual (page 25)
If venting fails
Clean pre-filter suction chamber

Clean the suction chamber only if venting fails after cleaning foams and valve box. Caution: Strong spring can act as a projectile.

Show in the manual (page 25)
M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend BioMaster Thermo?

Yes No

Frequently Asked Questions

A

Press the suction button on the pre-filter repeatedly until water flows steadily out of the outlet pipe. Ensure all air bubbles have escaped before turning on the pump to prevent damage.

Is this answer helpful?

A

Yes, the BioMaster Thermo is suitable for both freshwater and saltwater aquariums, provided you rinse the components thoroughly after each use to prevent corrosion.

Is this answer helpful?

A

The largest model, the BioMaster Thermo 600, is recommended for aquariums up to 600 liters. Smaller models cover 250 and 350 liters respectively.

Is this answer helpful?

A

Clean the pre-filter foam every two to four weeks, or more frequently if your tank has a heavy bioload. Rinse in tank water to preserve beneficial bacteria.

Is this answer helpful?

A

No, the heater should only be operated when water is circulating. Always disconnect power immediately if the pump fails to prevent overheating and potential fire hazards.

Is this answer helpful?

A

Turn off the unit, let it cool, unscrew the holding ring counter-clockwise, and remove the old heater. Insert the new one moistened with water and screw the ring back clockwise.

Is this answer helpful?

A

Loud noises usually indicate trapped air. Move the filter side to side to release air pockets or check if the intake pipe is clogged with debris.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Integrated heater saves space and simplifies setup
  • Multi-stage filtration with Hel-X bio-elements ensures excellent water quality
  • Tool-free connection unit allows for quick hose installation and removal
  • Adjustable flow rate lever provides precise control over water circulation
  • Easy access to internal components facilitates efficient cleaning and maintenance
VS

Disadvantages

  • Heater must cool down before removal to prevent glass breakage
  • Initial priming requires careful attention to avoid airlocks and noise
  • Filter media replacement can be costly if using original OASE parts
  • Unit height increases significantly when including the heater assembly
  • Requires regular monitoring to ensure pump does not run dry
M: QW-35-FL

Product Specification

Type

Thermo-External Filter

Suitability

Freshwater, Seawater, Aquariums

Connections

Rotatable valves with quick-release coupling, 16mm hose connection (inner diameter)

Features

With suction aid, 4.92ft cable length, includes inlet/outlet set

Manufacturer Warranty

Three years (+1 year upon registration)

M: QW-35-FL

Product Description

Elevate Your Aquarium with the Oase BioMaster Thermo External Filter

Maintaining a thriving aquatic environment requires reliable equipment that combines powerful filtration with precise temperature control. The Oase BioMaster Thermo Aquarium-Thermo-External Filter stands as a premier choice for aquarists seeking efficiency and stability in their tanks. This robust external filter is designed to handle aquariums ranging from 250 to 600 liters, offering versatile models tailored to specific volume needs.

The BioMaster Thermo series goes beyond simple water circulation. It integrates a high-quality heating element directly into the filtration system, ensuring that your water remains at the ideal temperature while being thoroughly cleaned. Whether you are keeping freshwater or saltwater species, this unit adapts seamlessly. The filtration process begins as water is drawn into the unit head by a powerful pump. It first passes through a pre-filter equipped with foam sponges of varying densities to trap large debris. From there, the water flows upward through multiple baskets containing Hel-X bio-elements and additional filter media, promoting beneficial bacterial growth essential for biological filtration.

One of the standout features of the BioMaster Thermo is its user-friendly design. The connection unit allows for easy attachment of hoses without tools, and the lever system securely locks the components in place while preventing water leakage during maintenance. The unit head can be quickly removed for deep cleaning, allowing you to replace or rinse filter media efficiently. Safety is paramount; the device includes protections against dry running and overheating, ensuring long-term reliability.

Installation is straightforward. The filter sits outside the tank, either below or beside it, utilizing gravity and suction cups to position intake and output pipes correctly. Before starting, users must ensure the system is fully primed to remove air pockets, which could cause noise or damage. Once operational, the flow rate can be adjusted via a simple lever on the connection unit, giving you complete control over water movement.

Regular maintenance keeps the BioMaster performing at its peak. The pre-filter foam should be rinsed regularly, and the internal baskets should be cleaned based on tank bioload. Because the filter uses a multi-stage approach, you can stagger cleaning cycles to preserve the beneficial bacteria colony within the system. With its durable construction and intelligent engineering, the Oase BioMaster Thermo ensures your aquarium stays crystal clear and perfectly heated year-round.

M: QW-35-FL

© Copyright 2026 Manual.ly