Manual.ly Logo

NAD C 268 Manual

0.0 · 0 Ratings

PDF manual · 10 Pages

English

M: gpt-5.6-terra
page

/ 10

Loading...
af3e9c9e9f41c5ff9905614e051676641a5a page 5
ENGLISH
5
QUICK START
Refer to the supplied C 268 Quick Setup Guide for basic instructions
in setting up your new NAD C 268. The following guidelines must be
observed when setting up your C 268.
1 Before setting up or making connections, ensure that the C 268 and other
devices to be connected to C 268 are unplugged or powered down.
2 Connect your speakers to the LEFT and RIGHT speaker terminals.
Connect the speaker cables to the corresponding speaker terminal
connections (R +/-, L +/-) as reected in the C 268 rear panel. Bare wire
or loose strands from the speaker cables must not touch the rear panel
or other speaker terminals.
3 Connect the line output terminal of your external sources to the
BALANCED and/or SINGLE-ENDED ANALOG AUDIO INPUT ports using
applicable connectors.
IMPORTANT NOTES
• The blue terminals must never be connected to ground (earth).
• Never connect the blue terminals together or to any common ground
device.
• Do not connect the output of this amplier to any headphone adapter,
speaker switch or any device that uses common ground for left and
right channels.
4 Connect corresponding end of the mains power cord to the AC mains
input of C 268 and the plug connected to a mains power source.
WARNING
For optimal performance, the C 268 requires a grounded AC receptacle
or a separate earth ground. Ensure the proper grounding of your system.
5 Maintain default settings of the following control switches’
• LEFT and RIGHT SELECT towards BALANCED or SINGLE-ENDED
(both switches must be of the same setting)
• INPUT SELECT to FIX
• AUTO SENSE LEVEL to MID
6 Set the POWER switch at the rear panel to “ON” setting. The Standby
LED indicator will illuminate amber. Press front panel STANDBY button
to turn ON the C 268. The Standby LED indicator will turn from amber
to blue. Your C 268 is now powered up!
SAVE THE PACKAGING
Please save the box and all of the packaging in which your C 268 arrived.
Should you move or otherwise need to transport your C 268, this is by far
the safest container in which to do so. We’ve seen too many otherwise
perfect components damaged in transit for lack of a proper shipping
carton, so please: Save that box!
NOTES ON INSTALLATION
• Place your NAD C 268 on a rm, level surface.
• Avoid placing the unit in direct sunlight or near sources of heat and
damp.
• Do not place the unit on a soft surface like a carpet.
• Do not place the C 268 in an enclosed position such as a bookcase
or cabinet that may impede the air-ow through the ventilation slots.
Allow adequate ventilation.
• Make sure the unit is switched o before making any connections.
• The RCA sockets on your C 268 are color coded for convenience. Red
and white are Right and Left audio respectively. Use high quality leads
and sockets for optimum performance and reliability.
• Ensure that leads and sockets are not damaged in any way and all
sockets are rmly pushed home.
• Should water get into your C 268, shut o the power to the unit and
remove the plug from the AC socket. Have the unit inspected by a
qualied service technician before attempting to use it again.
• Use a dry soft cloth to clean the unit. If necessary, lightly dampen the
cloth with soapy water. Do not use solutions containing benzol or other
volatile agents.
DO NOT REMOVE THE COVER; THERE ARE NO USERSERVICEABLE
PARTS INSIDE.
INTRODUCTION
GETTING STARTED

Chat with your NAD C 268 manual using AI

Get instant AI answers from your NAD C 268 manual

Ask anything about the NAD C 268. Answers come from this manual, with the pages they are based on.

C 268 Maintenance Schedule

Before cleaning
Unplug before cleaning

Unplug the product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners.

As needed
Clean with damp cloth

Use a damp cloth for cleaning. If necessary, lightly dampen the cloth with soapy water.

M: QW-35-FL

Ask a Question

0/1000

Do you recommend C 268?

Yes No

Frequently Asked Questions

A

The NAD C 268 delivers 80 watts per channel continuously into 8 ohms and 4 ohms with both channels driven. Its IHF dynamic power rating is 120 watts into 8 ohms and 200 watts into 4 ohms.

Is this answer helpful?

A

Yes. Switch on Bridge Mode and connect one 8-ohm speaker between the L+ and R- terminals. In this configuration, the amplifier provides approximately 300 watts of continuous power. Lower-than-8-ohm speakers are not recommended in bridge mode.

Is this answer helpful?

A

Yes. The amplifier has balanced XLR inputs as well as single-ended RCA inputs. XLR wiring uses pin 1 for ground, pin 2 for positive signal, and pin 3 for negative signal return.

Is this answer helpful?

A

Fixed mode sets the amplifier for use with an external component that controls volume, such as a preamplifier or processor. Variable mode lets you adjust input level with the INPUT LEVEL control, which works as a trim control rather than a complete volume control.

Is this answer helpful?

A

Yes. Auto Sense can bring the amplifier out of standby when it detects an input signal. It has low, mid, and high sensitivity settings. A 12 V trigger input can also switch it on from a compatible control component.

Is this answer helpful?

A

Yes. The LINE OUT connectors support daisy-chaining. Connect them to the corresponding analog input of another compatible amplifier, receiver, or processor to extend the system.

Is this answer helpful?

M: gpt-5.6-terra

Advantages and Disadvantages

Advantages

  • Delivers 80 W per channel into 8 or 4 ohms for capable stereo speaker drive.
  • Bridge mode provides about 300 W into 8 ohms for higher-output mono applications.
  • Includes balanced XLR and single-ended RCA inputs for broad system compatibility.
  • Auto sensing and 12 V trigger connections support convenient automated system control.
  • Line outputs allow daisy-chaining additional amplifiers in expanded installations.
VS

Disadvantages

  • Bridge mode is recommended only with 8-ohm speakers, limiting low-impedance mono setups.
  • The variable input control is level trimming, not a full front-panel volume control.
  • No digital, USB, HDMI, or wireless inputs are included; it is an analog power amplifier.
  • Blue speaker terminals must not be grounded or used with shared-ground accessories.
  • Adequate ventilation is essential to prevent overheating in enclosed installations.
M: gpt-5.6-terra

Product Specification

Channels

2

Power per Channel

80 W (8 ohm), 80 W (4 ohm)

Connections

Stereo Line In (RCA), Stereo Line In (XLR)

Power Consumption

0.5 W standby

Color

black

Dimensions

17.13 x 3.94 x 15.35 in (W x H x D)

Weight

16.09 lb

M: gpt-5.6-terra

Product Description

NAD C 268 Manual: Powerful Stereo Amplification for Flexible Systems

The NAD C 268 is a versatile stereo power amplifier designed for hi-fi and home theater systems that need clean power, flexible connections, and straightforward control. This model delivers 80 watts per channel into both 8 and 4 ohms in stereo operation, giving compatible speakers a strong, controlled foundation for music, movies, and everyday listening. For listeners building a system around a separate preamplifier, streaming component, or AV processor, the NAD C 268 Manual highlights the practical options available for integrating the amplifier.

Stereo Power and Bridged Mono Performance

A key feature of the C 268 is its bridge mode. When configured for mono operation and paired with an 8-ohm speaker, it can provide approximately 300 watts of continuous output. This makes it useful in larger setups or installations where extra headroom is needed. Two units can also be considered for high-power stereo arrangements, with each amplifier assigned to one channel.

The amplifier offers low measured distortion and a broad 20 Hz to 20 kHz frequency response. Its dynamic power capability reaches 120 watts into 8 ohms and 200 watts into 4 ohms in stereo mode, helping it handle demanding musical peaks. A damping factor above 100 also supports controlled speaker performance.

Connections and Everyday Control

The rear panel includes both balanced XLR and single-ended RCA analog inputs. Separate input selectors allow the left and right channels to use the desired connection type. Balanced connections can be especially valuable in installations where long cable runs or noise resistance are priorities, while RCA inputs provide easy compatibility with many conventional audio components.

A fixed or variable input mode adds installation flexibility. Fixed mode lets an external preamplifier or processor manage volume, while variable mode enables level trimming through the front-accessible rear-panel control. The C 268 also includes line output connections for daisy-chaining additional amplifiers.

Automation and Installation Features

The C 268 supports automatic signal sensing, with low, mid, and high trigger thresholds. It can wake from standby when it detects an incoming audio signal. A 12-volt trigger input and output provide another way to coordinate power status with compatible preamps, receivers, and system controllers.

For safe installation, use a grounded outlet, maintain ventilation clearance around the chassis, and verify speaker polarity before power-up. In bridge mode, NAD recommends 8-ohm speakers; lower impedances are not advised because the amplifier may activate thermal protection at high levels.

Notes

  • Do not connect the blue speaker terminals to ground or a shared common connection.
  • Keep the amplifier on a firm, level surface with clear airflow around it.
  • Use bridge mode only with correctly wired 8-ohm speakers.
  • Select fixed input mode when volume is controlled by an external preamplifier.
M: gpt-5.6-terra

© Copyright 2026 Manual.ly