Manual.ly Logo

Holzmann TS305 Manual

4.3 · 16 Ratings

PDF manual · 12 Pages

English

M: OA-GPT-54-NAN
page

/ 12

Loading...
ff8f5c7a167f922614faf8d549095404352f page 9
ENGLISH
HOLZMANN Maschinen Austria www.holzmann-maschinen.at Seite 9
Bedienungsanleitung Tellerschleifmaschine TS 305
If one or more parts of the machine are defec-
tive, the use of the machine is prohibited. De-
fective parts must be replaced immediately.
Only replacement parts which have been ap-
proved by the manufacturer may be used. It is
prohibited to make any changes to the ma-
chine.
Hazard due to electric shock:
Only operate the machine at a power source
which is protected by an appropriate residual-
current circuit breaker. Socket-outlets must be
properly installed, earthed and tested!
Hazard due to unintentional start-up of the
machine.
Hazard due to wood dust:
The inhalation of wood dust is a health hazard!
Damage to hearing if ear-muffs are not used
as necessary.
Harmful emissions of wood dust when used in
closed rooms.
6 OPERATION
6.1 Angle adjustments
To achieve perfect sanding results you have to
ensure that your machine parts are steadily ad-
justed properly. Prior to first operation an subse-
quently every 3 months you should check the
angle fit of your sanding table and your mitre
gauge.
For this you need a precise angle gauge.
Adjust sanding table
Loosen the fixing bolts, bring the sanding table
into 90° position so that the gauge aligns in a
degree of 90 to sanding disc and sanding table.
If the angle index on the machine side does not
match exactly the 90° it has to be readjusted.
Adjust angle gauge
Swing and fasten the already adjusted sanding
table into 90° position. Now bring the angle gauge
into 90° position to the sanding table and check
on the angle index if it matches exactly. If not ,
readjust the angle index.
6.2 Sanding table tilt
You can tilt the sanding table max. 45° down-
wards.
Loosen the fixing bolts on the left and right side,
bring the sanding table into the desired position
and do not forget to fasten the fixing bolts at the
end firmly again.
6.3 Turn on / Shut off
Turn the machine on by pressing the green ON
button
Shut the machine off by pressing the red OFF
button.
Let the yellow cap rest on the buttons during op-
eration. In the case of emergency pressure on the
yellow cap activates the smaller OFF button laying
below.
6.4 Operation Instructions
Let the disc sander reach its full speed before
starting to sand.
The angle gauge enables you to sand exactly and
more secure – so use it.
Do not force the machine! Do not attempt to sand
more than 0,3mm in one run. Use the correct
sanding paper for the job.
Do not sand any workpieces being shorter than
8mm or being thinner than 10mm.
Sever hazard of hand injury!
For surface sanding jobs of rather thin workpieces
we strongly recommend the use of feeding acces-
sories.
Always be aware of the rotation direction of the
sanding disc.
The sanding disc should always sand the work-
piece from up to down.
This prevents the hazard of workpiece kickback
and injuries.
7 MAINTENANCE
IMPORTANT: Disconnect the machine from
the power supply.
The HOLZMANN TS 305 is quasi maintenance
free.!
Do not use aggressive solvents or similar –
they will harm the machine surface.
Repairs may be carried out by professionals
only!
Sanding disc change
Turn the machine off and disconnect it from the
power supply.
Now remove the sanding table. You have to re-
move first all fixing bolts first.

Chat with your Holzmann TS305 manual using AI

Get instant AI answers from your Holzmann TS305 manual

Ask anything about the Holzmann TS305. Answers come from this manual, with the pages they are based on.

TS305 Maintenance Schedule

Remind me when maintenance is due
Every 3 months
Check angle accuracy of table and gauge

Verify the sanding table and mitre gauge are set to 90 degrees using a precise angle gauge. Readjust if the index does not match exactly.

After each use
Clean machine from dust

Disconnect power. Remove wood dust ideally with compressed air or a dry cloth, followed by a slightly damp cloth. Do not use aggressive cleaners.

Free maintenance reminders

Timed to your purchase date. Always free, unsubscribe anytime.

By submitting you agree to the privacy policy. Unsubscribe with one click in any email.
M: QW-35-FL

Ask a Question

0/1000

Do you recommend TS305?

Yes No
0
User Pic

Kristin Hirsch

10 months ago

How loud is this disc sander and does it vibrate much while grinding?

0
User Pic

Manual.ly

10 months ago

Customers report a very quiet and smooth running machine with low vibration. Because the unit is heavy (cast body) and has rubber feet, it stays stable on the workbench and vibrations are largely absorbed, resulting in a calm working sound. Several users specifically mention a quiet operation and almost vibration-free behavior during sanding. If you plan to use attachments/angle guides, just make sure everything is set firmly and aligned, so the workpiece and accessories do not introduce extra movement.

M: OA-GPT-5-NAN
M: OA-GPT-5-NAN

Frequently Asked Questions

A

It is designed for sanding small wooden workpieces and wood-based materials. It works especially well for edge finishing, bevels, and precise shaping tasks in a workshop setting.

Is this answer helpful?

A

Yes. The sanding table can be tilted from 0° to 45°, which helps with angled sanding and more flexible workpiece positioning.

Is this answer helpful?

A

It can be used by beginners only if they are properly trained and follow the safety instructions carefully. Protective equipment and correct feeding technique are very important.

Is this answer helpful?

A

Feed the workpiece so the disc moves from above into the material. Also avoid taking too deep a cut and do not sand pieces that are too short or too thin.

Is this answer helpful?

A

Routine cleaning, checking fasteners, and replacing worn sanding discs are the main tasks. The machine should always be disconnected from power before maintenance.

Is this answer helpful?

A

No. The machine is intended for indoor use only. It should be kept in a dry, clean, and well-ventilated workshop area.

Is this answer helpful?

M: OA-GPT-54-NAN

Advantages and Disadvantages

Advantages

  • 305 mm disc and 750W motor provide solid sanding power for small workshop tasks.
  • Tilting table and mitre gauge support accurate edge work and angled sanding.
  • Maintenance is simple, with easy cleaning and straightforward sanding disc replacement.
  • Built-in emergency-off switch and clear safety guidance improve operator control.
VS

Disadvantages

  • Designed mainly for small workpieces, so it is not ideal for large stock removal.
  • Noise levels are noticeable, making hearing protection important.
  • Dust management is essential because sanding can create harmful fine particles.
  • Requires careful setup and trained use to avoid kickback and inaccurate results.
M: OA-GPT-54-NAN

Product Specification

Power

750 W

No-load speed

1,450 rpm

Disc diameter

12.01 in

Tool mounting

Hook and loop

Special features

Dust extraction, Angle stop

Weight

59.52 lb

M: OA-GPT-54-NAN

Product Description

Holzmann TS305 Electric Disc Sander: Compact Power for Precise Woodworking

The Holzmann TS305 Electric Disc Sander is built for woodworkers who want accurate edge shaping and smooth sanding in a compact machine. Designed for small workpieces made of wood and wood-based materials, it combines a 750W motor with a 305 mm sanding disc to deliver steady performance for workshop tasks that demand control rather than brute force. For anyone looking into the Holzmann TS305 Electric Disc Sander Manual, the key takeaway is that this machine is all about precision, safe handling, and consistent setup.

One of the most useful features of the TS305 is its adjustable sanding table, which tilts from 0° to 45°. This makes it practical for bevels, angled edges, and repeatable shaping tasks. The included mitre gauge helps keep workpieces aligned, while the large table surface supports stable feeding. With two operating speeds, the machine offers flexibility for different sanding needs, and the angle settings can be checked and fine-tuned for better accuracy over time.

Safety is a major part of the TS305 experience. The machine is meant to be used by trained users only, with proper eye, ear, and respiratory protection. The manual strongly emphasizes clean working conditions, stable placement, and correct feed direction so the sanding disc always moves from above the workpiece downward. That approach reduces kickback risk and helps achieve cleaner results. Because fine dust can be harmful, good ventilation and dust protection are not optional extras but essential habits.

Maintenance is straightforward, which is another advantage for busy workshops. Regular cleaning, checking fastening bolts, and replacing the sanding disc when worn are the main routine tasks. The machine is not designed for heavy disassembly, and repairs should be left to professionals. This keeps downtime low and helps the sander stay reliable over the long term.

Overall, the TS305 suits hobbyists and small professional shops that need a dedicated disc sander for detailed work. It is not a machine for oversized stock or aggressive material removal, but it shines when accuracy, repeatability, and safe operation matter most. For woodworking projects involving edges, corners, and small components, it offers a balanced mix of power and control.

Notes

  • Best for small wooden workpieces and wood composites.
  • Always verify table and gauge angles before precise sanding.
  • Use dust protection and hearing protection during operation.
  • Keep the machine on a stable surface and away from moisture.
M: OA-GPT-54-NAN

© Copyright 2026 Manual.ly