Manual.ly Logo

GYS TIG 200 DC HF FV Manual

0.0 · 0 Ratings

PDF manual · 80 Pages

English

M: OA-GPT-54-NAN
page

/ 80

Loading...
336d0675033ab5e56257cc17c9ee58c43e6e page 10
16
TIG 168 / TIG 200 DC
MADE IN FRANCE
EN
MAINTENANCE / RECOMMENDATIONS
• Maintenance should only be carried out by a qualied person. Annual maintenance is recommended.
• Ensure the machine is unplugged from the mains, and wait for two minutes before carrying out main-
tenance work. DANGER High Voltage and Currents inside the machine.
• Remove the casing 2 or 3 times a year to remove any excess dust. Take this opportunity to have the
electrical connections checked by a qualied person, with an insulated tool.
• Regularly check the condition of the power supply cable. If the power cable is damaged, it must be
replaced by the manufacturer, its after sales service or an equally qualied person.
• Ensure the ventilation holes of the device are not blocked to allow adequate air circulation.
• Do not use this equipment to thaw pipes, to charge batteries, or to start any engine.
INSTALLATION – FONCTIONNEMENT PRODUIT
DESCRIPTION
The TIG 168/200 HF are portable, single phase ventilated Inverter welding units to be used with non-consumable elec-
trodes (TIG) in direct current (DC). TIG DC welding requires a gaseous protection (Argon). In MMA mode, it allows you
to weld with any kind of electrode : rutile, basic, stainless steel or cast iron. The TIG 168 work with a single phase 230V
input. The TIG 200 FV works on a single phase input between 85V to 265V. They are all protected for a use on electric
generators. The TIG 200 can be equipped with a remote control or foot pedal (This option is supplied separately).
ALIMENTATION-MISE EN MARCHE
• This machine is tted with a 16A socket type CEE7/7 which must be connected to a single-phase 230V (50 - 60 Hz)
power supply tted with three wires and one earthed neutral.
The absorbed effective current (I1eff) is displayed on the machine, for optimal use. Check that the power supply and
its protection (fuse and/or circuit breaker) are compatible with the current needed by the machine. In some countries,
it may be necessary to change the plug to allow the use at maximum settings.
• To start the machine up, press the Standby Button «
»
• NB: If the screen displays
. this indicates that the device has entered protection mode. This will occur if the
power supply voltage is excessively high (over 265V). If the machine switches on in protection mode, unplug the device
and plug it into a socket delivering the correct voltage.
CONNECTION ON A GENERATOR
The machine can work with generators as long as the auxiliary power matches these requirements :
- The voltage must be AC, always set as specied, and the peak voltage below 400V,
- The frequency must be between 50 and 60 Hz.
It is imperative to check these requirements as several generators generate high voltage peaks that can damage these
machines.
MMA WELDING (ELECTRODE)
Getting Started
• Connect the electrode holder and earth clamp to the corresponding sockets.
• Ensure that the welding polarities and intensities indicated on the electrode packaging are observed.
• Remove the electrode from the electrode holder when the machine is not in use.
Welding Features:
Your device is equipped with 3 specic functions :
Hot Start gives an adjustable* overcurrent at the beginning of the welding.
Arc Force delivers an overcurrent which avoids sticking when the electrode enters the weld pool.
Anti-Sticking allows easy removal of the electrode in case of sticking.
Selection of process and current setting
1- Select MMA mode 2- Select the desired current using the potentiometer
Nb. : The TIG 200FV, the welding current will vary depending on the power supply voltage used:
- on 110V, the current can be set from 10 to 120A.
- on 230V, the current can be set from 10 to 200A.

Chat with your GYS TIG 200 DC HF FV manual using AI

Get instant AI answers from your GYS TIG 200 DC HF FV manual

Ask anything about the GYS TIG 200 DC HF FV. Answers come from this manual, with the pages they are based on.

TIG 200 DC HF FV Maintenance Schedule

Remind me when maintenance is due
Yearly
Annual maintenance check

Have a qualified person perform routine maintenance and verify electrical safety.

Every 4 months
Remove casing and clean dust

Remove the cover 2 to 3 times a year to remove excess dust using compressed air.

Show in the manual (page 16)

Free maintenance reminders

Timed to your purchase date. Always free, unsubscribe anytime.

By submitting you agree to the privacy policy. Unsubscribe with one click in any email.
M: QW-35-FL

Ask a Question

0/1000

Do you recommend TIG 200 DC HF FV?

Yes No

Frequently Asked Questions

A

It is mainly suited for DC TIG welding with argon protection, but it also supports MMA stick welding. That makes it useful for precision work, repairs, and general workshop tasks.

Is this answer helpful?

A

Yes. HF start allows non-contact ignition for clean starts, while Lift mode is useful when high-frequency starts are not suitable or when reduced interference is preferred.

Is this answer helpful?

A

Yes, the machine is designed to work with compatible generators, provided the output is stable and meets the required voltage and frequency limits.

Is this answer helpful?

A

In MMA mode it can handle rutile, basic, stainless steel, and cast iron electrodes. In TIG DC mode it is intended for steels and similar DC-compatible materials.

Is this answer helpful?

A

These modes help reduce heat input and improve control on thinner parts or sensitive joints. They also help limit distortion and create a more controlled weld pool.

Is this answer helpful?

A

Yes, it includes five memory slots for saving and recalling common TIG settings, which speeds up repeat jobs and helps keep weld parameters consistent.

Is this answer helpful?

M: OA-GPT-54-NAN

Advantages and Disadvantages

Advantages

  • Wide voltage range on the FV model supports unstable or mixed-site power conditions.
  • HF and Lift start options offer cleaner arc initiation in different environments.
  • TIG, MMA, Pulse, Easy Pulse, Spot, and memory functions improve versatility.
  • Remote control and foot pedal compatibility help fine-tune welding current.
VS

Disadvantages

  • TIG welding requires shielding gas, so extra setup and consumables are needed.
  • Advanced settings may take time to learn for beginners.
  • The machine is intended for DC welding only, not AC applications.
  • Proper ventilation and strict safety measures are essential during use.
M: OA-GPT-54-NAN

Product Specification

Power

9.39hp (110-230V)

Open-circuit voltage

76V

Control range

5-200A (TIG)

Dimensions

12.20x16.54x5.91in (HxWxD)

Weight

26.46lb

M: OA-GPT-54-NAN

Product Description

GYS TIG 200 DC HF FV Inverter Welding Machine: Compact Power for Precise Welding

The GYS TIG 200 DC HF FV Inverter welding machine incl. accessories Manual points to a versatile machine built for welders who want control, portability, and dependable performance. This inverter unit is designed for DC TIG welding with argon shielding, while also supporting MMA stick welding for routine repair jobs and mixed workshop use.

Built for flexibility

One of the standout strengths of the TIG 200 DC HF FV is its wide input range on the FV version, making it a practical choice for sites where power conditions are not always ideal. It is also generator-friendly, which adds mobility for field work, maintenance teams, and installers. The machine combines HF ignition for clean, contact-free arc starts with Lift mode for environments where high-frequency start is not preferred.

Useful features for cleaner results

This welder offers several functions that help improve arc quality and weld finish. Two-step and four-step trigger modes make long seams more comfortable, while 4T Log adds a convenient switch between hot and cold current during welding. Pulse and Easy Pulse reduce heat build-up, which is especially helpful when working on thinner materials or when controlling distortion matters. A Spot mode is also available for tacking parts before final welding.

Practical control and storage

The interface is built around fast setup and repeatable results. Users can adjust pre-gas, up-slope, welding current, pulse frequency, cold current, down-slope, and post-gas to suit the joint and material. Five memory slots allow common settings to be saved and recalled quickly. On compatible configurations, remote control or a foot pedal adds even finer current adjustment.

Why it stands out

For hobbyists with higher expectations and professionals who need a reliable DC TIG platform, this machine offers a balanced mix of portability and function. It supports stainless steel, mild steel, cast iron, and rutile or basic electrodes in MMA mode. The included accessories and the clear logic of the control system make it easier to move from setup to production without wasted time.

Notes

  • Use proper ventilation and full protective gear during welding.
  • Argon shielding is required for TIG operation.
  • Let the torch cool before maintenance.
  • Keep cables fully uncoiled to avoid overheating.
M: OA-GPT-54-NAN

© Copyright 2026 Manual.ly