Manual.ly Logo

GYS TIG 200 DC HF FV Manual

0.0 · 0 Ratings

PDF manual · 80 Pages

English

M: OA-GPT-54-NAN
page

/ 80

Loading...
336d0675033ab5e56257cc17c9ee58c43e6e page c
12
TIG 168 / TIG 200 DC
MADE IN FRANCE
EN
WARNING - SAFETY RULES
GENERAL INSTRUCTIONS
Read and understand the following safety recommendations before using or servicing the unit.
Any change or servicing that is not specied in the instruction manual must not be undertaken.
The manufacturer is not liable for any injury or damage caused due to non-compliance with the instructions featured
in this manual .
In the event of problems or uncertainties, please consult a qualied person to handle the installation properly.
ENVIRONMENT
This equipment must only be used for welding operations in accordance with the limits indicated on the descriptive panel
and/or in the user manual. The operator must respect the safety precautions that apply to this type of welding. In case
of inedaquate or unsafe use, the manufacturer cannot be held liable for damage or injury.
This equipment must be used and stored in a place protected from dust, acid or any other corrosive agent. Operate the
machine in an open, or well-ventilated area.
Operating temperature:
Use between -10 and +40°C (+14 and +104°F).
Store between -20 and +55°C (-4 and 131°F).
Air humidity:
Lower or equal to 50% at 40°C (104°F).
Lower or equal to 90% at 20°C (68°F).
Altitude:
Up to 1000 meters above sea level (3280 feet).
INDIVIDUAL PROTECTIONS AND OTHERS
Arc welding can be dangerous and can cause serious and even fatal injuries.
Welding exposes the user to dangerous heat, arc rays, electromagnetic elds, noise, gas fumes, and electrical shocks.
People wearing pacemakers are advised to consult with their doctor before using this device.
To protect oneself as well as the other, ensure the following safety precautions are taken:
In order to protect you from burns and radiations, wear clothing without cuffs. These clothes must be
insulated, dry, reproof and in good condition, and cover the whole body.
Wear protective gloves which guarantee electrical and thermal insulation.
Use sufcient welding protective gear for the whole body: hood, gloves, jacket, trousers... (varies depen-
ding on the application/operation). Protect the eyes during cleaning operations. Do not operate whilst
wearing contact lenses.
It may be necessary to install reproof welding curtains to protect the area against arc rays, weld spatters
and sparks.
Inform the people around the working area to never look at the arc nor the molten metal, and to wear
protective clothes.
Ensure ear protection is worn by the operator if the work exceeds the authorised noise limit (the same
applies to any person in the welding area).
Stay away from moving parts (e.g. engine, fan...) with hands, hair, clothes etc...
Never remove the safety covers from the cooling unit when the machine is plugged in - The manufac-
turer is not responsible for any accident or injury that happens as a result of not following these safety
precautions.

Chat with your GYS TIG 200 DC HF FV manual using AI

Get instant AI answers from your GYS TIG 200 DC HF FV manual

Ask anything about the GYS TIG 200 DC HF FV. Answers come from this manual, with the pages they are based on.

TIG 200 DC HF FV Maintenance Schedule

Remind me when maintenance is due
Yearly
Annual maintenance check

Have a qualified person perform routine maintenance and verify electrical safety.

Every 4 months
Remove casing and clean dust

Remove the cover 2 to 3 times a year to remove excess dust using compressed air.

Show in the manual (page 16)

Free maintenance reminders

Timed to your purchase date. Always free, unsubscribe anytime.

By submitting you agree to the privacy policy. Unsubscribe with one click in any email.
M: QW-35-FL

Ask a Question

0/1000

Do you recommend TIG 200 DC HF FV?

Yes No

Frequently Asked Questions

A

It is mainly suited for DC TIG welding with argon protection, but it also supports MMA stick welding. That makes it useful for precision work, repairs, and general workshop tasks.

Is this answer helpful?

A

Yes. HF start allows non-contact ignition for clean starts, while Lift mode is useful when high-frequency starts are not suitable or when reduced interference is preferred.

Is this answer helpful?

A

Yes, the machine is designed to work with compatible generators, provided the output is stable and meets the required voltage and frequency limits.

Is this answer helpful?

A

In MMA mode it can handle rutile, basic, stainless steel, and cast iron electrodes. In TIG DC mode it is intended for steels and similar DC-compatible materials.

Is this answer helpful?

A

These modes help reduce heat input and improve control on thinner parts or sensitive joints. They also help limit distortion and create a more controlled weld pool.

Is this answer helpful?

A

Yes, it includes five memory slots for saving and recalling common TIG settings, which speeds up repeat jobs and helps keep weld parameters consistent.

Is this answer helpful?

M: OA-GPT-54-NAN

Advantages and Disadvantages

Advantages

  • Wide voltage range on the FV model supports unstable or mixed-site power conditions.
  • HF and Lift start options offer cleaner arc initiation in different environments.
  • TIG, MMA, Pulse, Easy Pulse, Spot, and memory functions improve versatility.
  • Remote control and foot pedal compatibility help fine-tune welding current.
VS

Disadvantages

  • TIG welding requires shielding gas, so extra setup and consumables are needed.
  • Advanced settings may take time to learn for beginners.
  • The machine is intended for DC welding only, not AC applications.
  • Proper ventilation and strict safety measures are essential during use.
M: OA-GPT-54-NAN

Product Specification

Power

9.39hp (110-230V)

Open-circuit voltage

76V

Control range

5-200A (TIG)

Dimensions

12.20x16.54x5.91in (HxWxD)

Weight

26.46lb

M: OA-GPT-54-NAN

Product Description

GYS TIG 200 DC HF FV Inverter Welding Machine: Compact Power for Precise Welding

The GYS TIG 200 DC HF FV Inverter welding machine incl. accessories Manual points to a versatile machine built for welders who want control, portability, and dependable performance. This inverter unit is designed for DC TIG welding with argon shielding, while also supporting MMA stick welding for routine repair jobs and mixed workshop use.

Built for flexibility

One of the standout strengths of the TIG 200 DC HF FV is its wide input range on the FV version, making it a practical choice for sites where power conditions are not always ideal. It is also generator-friendly, which adds mobility for field work, maintenance teams, and installers. The machine combines HF ignition for clean, contact-free arc starts with Lift mode for environments where high-frequency start is not preferred.

Useful features for cleaner results

This welder offers several functions that help improve arc quality and weld finish. Two-step and four-step trigger modes make long seams more comfortable, while 4T Log adds a convenient switch between hot and cold current during welding. Pulse and Easy Pulse reduce heat build-up, which is especially helpful when working on thinner materials or when controlling distortion matters. A Spot mode is also available for tacking parts before final welding.

Practical control and storage

The interface is built around fast setup and repeatable results. Users can adjust pre-gas, up-slope, welding current, pulse frequency, cold current, down-slope, and post-gas to suit the joint and material. Five memory slots allow common settings to be saved and recalled quickly. On compatible configurations, remote control or a foot pedal adds even finer current adjustment.

Why it stands out

For hobbyists with higher expectations and professionals who need a reliable DC TIG platform, this machine offers a balanced mix of portability and function. It supports stainless steel, mild steel, cast iron, and rutile or basic electrodes in MMA mode. The included accessories and the clear logic of the control system make it easier to move from setup to production without wasted time.

Notes

  • Use proper ventilation and full protective gear during welding.
  • Argon shielding is required for TIG operation.
  • Let the torch cool before maintenance.
  • Keep cables fully uncoiled to avoid overheating.
M: OA-GPT-54-NAN

© Copyright 2026 Manual.ly