Manual.ly Logo

FSP NanoFit Manual

0.0 · 0 Ratings

PDF manual · 28 Pages

English

M: OA-GPT-54-NAN
page

/ 28

Loading...
732090c92300dda57af1719fbf32fac65b9d page 2
Standby UPS
400VA/600VA/800VA
SAVE THESE INSTRUCTION-This manual contains important instructions that should be followed
during installation and maintenance of the UPS and batteries.
● This UPS utilizes voltage that may be hazardous. Do not
attempt to disassemble the unit. The unit contains no user
replaceable parts. Only factory service personnel may
perform repairs.
● This pluggable type A equipment with battery already installed
by the supplier is operator installable and may be operated by
laymen.
● The mains socket outlet that supplies the UPS shall be installed
near the UPS and shall be easily accessible.
● During the installation of this equipment it should be assured
that the sum of the leakage currents of the UPS and the
connected loads does not exceed 3.5mA.
● Connection to any other type of receptacle other than a
two-pole, three-wire grounded receptacle may result in shock
hazard as well as violate local electrical codes.
● In the event of an emergency, press the "OFF" button and
disconnect the power cord from the AC power supply to
properly disable the UPS.
● Do not allow any liquids or any foreign object to enter the UPS.
Do not place beverages or any other liquid-containing vessels
on or near the unit.
● This unit intended for installation in a controlled environment
(temperature controlled, indoor area free of conductive
contaminants). Avoid installing the UPS in locations where
there is standing or running water, or excessive humidity.
● Do not plug the UPS input into its own output.
● Do not attach a power strip or surge suppressor to the UPS.
● Do not attach non-computer-related items, such as medical
equipment, life-support equipment, microwave ovens, or
vacuum cleaners to UPS.
● Do not dispose of batteries in a fire as they may explode.
● Internal battery voltage is 12VDC.Sealed, lead-acid, 6-cell
battery.
● A battery can present a risk of electrical shock and high short
circuit current. The following precautions should be observed
when working on batteries:
1)
Remove watches, rings, or other metal objects from the hands.
2)
Use tools with insulated handles.
3)
Wear rubber gloves and boots.
4)
Do not lay tools or metal parts on top of batteries.
5)
Disconnect charging source prior to connecting or
disconnecting batteries terminal.
● Servicing of batteries should be performed or supervised by
personnel knowledgeable of batteries and the required
precautions. Keep unauthorized personnel away from
batteries.
● When replacing batteries, replace with the same number and
type of sealed lead-acid battery.
● Do not open or mutilate the battery or batteries. Release
electrolyte is harmful to the skin and eyes. It may be toxic.
● Attention, hazardous through electric shock. Also with dis-
connection of this unit from the mains, hazardous voltage still
may be accessible through supply from battery. The battery
supply should be therefore disconnected in the plus and minus
pole at the connectors of the battery when maintenance or
service work inside the UPS is necessary.
● To reduce the risk of overheating the UPS, do not cover the
UPS' cooling vents and avoid exposing the unit to direct
sunlight or installing the unit near heat emitting appliances such
as space heater or furnaces.
● Unplug the UPS prior to cleaning and do not use liquid or spray
detergent.
● WARNING: This is a category C2 UPS product. In a residential
environment, this product may cause radio interference, in
which case the user many be required to take additional
measures.
MODEL
400
600
800
CAPACITY
400VA/
240W
600VA/
360W
800VA/
480W
Input Voltage
220/230/240 VAC
Input Voltage Range
180-270 VAC
Output Voltage
Regulation
± 10 % (Bat. mode)
Transfer Time
Typical 2-6 ms
Waveform
Simulated Sine Wave
Battery Type
12V/4Ah
12V/4.5Ah
12V/5Ah
Battery Number
1
1
1
Charging Time
8 hours recover to 90% capacity
Dimension (DxWxH)mm
305 x 158.5 x 95
Net Weight (kgs)
2.5
2.6
2.9
Humidity
0-90% RH @ 0-40°C non-condensing)
Noise Level
Less than 40dB
*Specifications are subject to change without notice.
If any abnormal situations occur that are not listed above, please
call for service immediately.
Problem
Possible Cause
Solutions
Nothing is
displayed on
the panel.
The UPS is not on.
Press the power switch
again to turn on the UPS.
Battery voltage is too
low.
Charge the battery at least
6 hours.
Battery fault.
Replace the battery.
The UPS
always on
battery mode.
Power cord loose.
Re-plug the power cord.
The UPS
continuously
beeps.
Please check the fault
code for the details.
Please check the fault code
for the details.
Backup time
too short.
Battery voltage is too
low.
Charge the battery at least
6 hours.
Overload.
Remove some unnecessary
loads. Before reconnecting
equipment, please verify
that the load matches the
UPS capability specified in
the specs.
Battery defect.
Replace the battery.

Chat with your FSP NanoFit manual using AI

Get instant AI answers from your FSP NanoFit manual

Ask anything about the FSP NanoFit. Answers come from this manual, with the pages they are based on.

NanoFit Maintenance Schedule

Before first use
Charge battery before initial use

Charge the battery for 6 hours prior to initial use for best results.

Before cleaning
Unplug unit before cleaning

Unplug the UPS from AC power before cleaning and do not use liquid or spray detergents.

M: QW-35-FL

Ask a Question

0/1000

Do you recommend NanoFit?

Yes No

Frequently Asked Questions

A

It is designed to provide short-term backup power and surge protection for computers, monitors, and other small office devices. It helps prevent sudden shutdowns and supports safer operation during power issues.

Is this answer helpful?

A

The recommended initial charge is about 6 hours. This helps prepare the internal battery for stable performance before you rely on it for backup power.

Is this answer helpful?

A

Use the battery backup outlets for critical equipment such as a computer and monitor. These outlets provide battery support, filtering, and surge protection during outages.

Is this answer helpful?

A

No. The text warns against connecting laser printers or scanners to battery backup sockets because they can draw too much power and overload the UPS.

Is this answer helpful?

A

The LED or LCD display shows power status, input and output voltage, load level, and battery capacity. It also warns about overload, low battery, and faults through icons and alarms.

Is this answer helpful?

A

Disconnect unnecessary or short-circuited loads and restart the unit. If the fault remains, or if the device reports high output voltage, contact service immediately.

Is this answer helpful?

A

Battery replacement should follow the same type and rating used by the unit, but the text emphasizes that internal service is for qualified personnel. If you are unsure, use professional support.

Is this answer helpful?

M: OA-GPT-54-NAN

Advantages and Disadvantages

Advantages

  • Three battery-backed outlets help keep a PC and monitor running during outages.
  • Three surge-protected outlets provide added protection for peripherals without draining backup power.
  • LCD/LED indicators and alarms make it easy to track voltage, load, and battery status.
  • Compact, lightweight design and quiet operation suit desks, small offices, and home setups.
VS

Disadvantages

  • Not suitable for high-draw devices like laser printers on battery-backed sockets.
  • Single-battery design limits runtime for larger loads or extended outages.
  • Internal parts are not user-serviceable, so repairs and some battery issues need professional help.
  • Designed for controlled indoor environments, so heat, humidity, and liquids are concerns.
M: OA-GPT-54-NAN

Product Specification

Type

Power strip with integrated UPS

Classification

VFD (Off-Line)

Voltage

230V

Outputs

6x Schuko, 2x USB-A (5V/1A)

Charging time

8h (90%)

Weight

6.61 lb

Dimensions (WxHxD)

6.26x3.74x12.01in

Manufacturer's warranty

two years

M: OA-GPT-54-NAN

Product Description

FSP NanoFit UPS: Compact Backup Power for Everyday Protection

The FSP NanoFit UPS is a practical standby power solution designed to keep essential electronics running when the mains supply becomes unstable or fails. Available in 400VA, 600VA, and 800VA variants, it focuses on the needs of home offices and small workspaces where reliable backup, surge defense, and simple operation matter most. If you are looking for a compact unit that is easy to set up and easy to understand, the FSP NanoFit UPS Manual reflects exactly that philosophy: clear steps, straightforward connections, and practical safety guidance.

At its core, this UPS is meant to protect computers, monitors, and other sensitive office devices. Three battery-backed outlets provide automatic support during outages, while three surge-protected outlets are better suited for accessories such as printers, scanners, or fax machines. It also adds EMI filtering, line conditioning, and surge suppression, helping connected equipment stay safer in day-to-day use. The transfer time is typically only a few milliseconds, so the switch to battery power is quick enough to prevent most interruptions.

Monitoring is simple thanks to LED or LCD status indicators. Users can check output voltage, input voltage, load level, and battery capacity with a touch, while alerts warn of overload, low battery, or fault conditions. That makes the unit easier to manage than a basic power strip, especially when power quality is inconsistent. The simulated sine wave output and sealed lead-acid battery design further underline its role as a dependable everyday backup tool rather than a complex enterprise system.

The design is also compact and lightweight, which makes placement easier on or under a desk. A recommended initial charge of around six hours helps the battery reach a solid starting point, and the unit can recover to most of its capacity within about eight hours. For best results, it should be used indoors in a controlled environment, with vents left clear and liquids kept away from the unit.

Notes

  • Best suited for PCs, monitors, and similar office equipment.
  • Keep laser printers and other heavy loads off battery-backed outlets.
  • Replace batteries only with the same type and rating.
  • Use the status display and alarms to spot overloads early.

Quick takeaway

The FSP NanoFit UPS combines small size, useful runtime support, and essential power protection into a simple package that fits modern everyday computing needs.

M: OA-GPT-54-NAN

© Copyright 2026 Manual.ly