Manual.ly Logo

Bosch DIY UniversalImpact 700 Manual

0.0 · 0 Ratings

PDF manual · 118 Pages

English

M: QW-35-FL
page

/ 118

Loading...
e35a37d115b73ee91ece09e9be990796fe8c page 14
20 | English
1 609 92A 2A0 | (17.11.16) Bosch Power Tools
Prevent dust accumulation at the workplace. Dust can
easily ignite.
Use the dust box only when working on concrete and
stone. Wood chips and plastic chips can easily lead to
clogging.
Warning: Danger of fire! Do not work on any metallic
materials with the dust box mounted. Hot metal chips
can ignite parts of the dust box.
Please observe the following instructions to optimise your use
of the dust box:
– Ensure that the dust box is placed flush against the work-
piece or wall. This also makes it easier to drill at a right an-
gle.
– After reaching the desired drilling depth, pull the drill bit
out of the drill hole first and then switch off the impact drill.
– The dust protection ring 15 can wear, especially when
working with large drill-bit diameters. Replace the dust
protection ring when worn/damaged.
Changing the Tool
Keyless Chuck (UniversalImpact 700,
UniversalImpact 700 + Drill Assistant) (see figure H)
Press the spindle lock button 2 only when the machine
is at a standstill.
The drill spindle is locked by pressing the spindle lock button
2. This makes quick and easy changing of the tool in the drill
chuck possible.
Open the keyless chuck 1 by turning in rotation direction ,
until the tool can be inserted. Insert the tool.
Firmly tighten the collar of the keyless chuck 1 by hand in ro-
tation direction until the locking action (“click”) is no longer
heard. This automatically locks the chuck.
The lock will disengage again if you turn the sleeve in the op-
posite direction to remove the tool with the spindle locking
button pressed.
Keyless Chuck (UniversalImpact 800) (see figure I)
The drill spindle is locked when the On/Off switch 6 is not
pressed. This makes quick, convenient and easy changing of
the tool in the drill chuck possible.
Open the keyless chuck 1 by turning in rotation direction ,
until the tool can be inserted. Insert the tool.
Firmly tighten the collar of the keyless chuck 1 by hand in ro-
tation direction until the locking action (“click”) is no longer
heard. This automatically locks the chuck.
The locking is released again to remove the tool when the col-
lar is turned in the opposite direction.
Key Type Drill Chuck (UniversalImpact 650)
(see figure J)
Press the spindle lock button 2 only when the machine
is at a standstill.
The drill spindle is locked by pressing the spindle lock button
2. This makes quick and easy changing of the tool in the drill
chuck possible.
Wear protective gloves when changing the tool. The
drill chuck can become very hot during longer work peri-
ods.
Open the key type drill chuck 28 by turning until the tool can
be inserted. Insert the tool.
Insert the chuck key 29 into the corresponding holes of the
key type drill chuck 28 and clamp the tool uniformly.
Screwdriver Tools
When working with screwdriver bits 25, a universal bit holder
24 should always be used. Use only screwdriver bits that fit
the screw head.
For driving screws, always position the “Drilling/Impact Drill-
ing” selector switch 3 to the “Drilling” symbol.
Replacing the Drill Chuck
Before any work on the machine itself, pull the mains
plug.
Removing the Drill Chuck (see figure K)
Remove the auxiliary handle 9.
Insert a steel pin with a diameter of Ø 4 mm and approx.
50 mm of length into the drill hole on the spindle neck in order
to lock the drill spindle.
Clamp the short end of a hex key 27 into the keyless chuck 1.
Place the machine on a stable surface (e. g. a workbench).
Hold the machine firmly and loosen the keyless chuck 1 by
turning the hex key 27 in rotation direction . Loosen a tight-
seated keyless chuck by giving the long end of the hex key 27
a light blow. Remove the hex key from the keyless chuck and
completely unscrew the keyless chuck.
Mounting the Drill Chuck (see figure L)
The keyless chuck is mounted in reverse order.
Remove the steel pin from the drill hole on the spindle
neck after mounting is completed.
The drill chuck must be tightened with a tightening
torque of approx. 30–35 Nm.
OBJ_BUCH-2862-001.book Page 20 Thursday, November 17, 2016 2:40 PM

Chat with your Bosch DIY UniversalImpact 700 manual using AI

Get instant AI answers from your Bosch DIY UniversalImpact 700 manual

Ask anything about the Bosch DIY UniversalImpact 700. Answers come from this manual, with the pages they are based on.

UniversalImpact 700 Maintenance Schedule

After every use
Empty dust box

Remove the dust box by pressing unlocking buttons and pull down. Empty it and reinsert until it clicks.

Show in the manual (page 12)
As needed
Clean machine and ventilation slots

Keep the machine and ventilation slots clean for safe and proper working before any work.

Show in the manual (page 14)
When worn
Replace dust protection ring

Replace the dust protection ring when worn or damaged, especially after working with large drill-bit diameters.

Show in the manual (page 20)
M: QW-35-FL

Ask a Question

0/1000

Do you recommend UniversalImpact 700?

Yes No

Frequently Asked Questions

A

This machine is designed for impact drilling in brick concrete and stone as well as for drilling in wood metal ceramic and plastic. It can also be used for screwdriving when using the appropriate mode and bits.

Is this answer helpful?

A

Open the keyless chuck by turning it in the correct direction. Insert the tool and tighten the collar by hand until you hear a click. This automatically locks the chuck for secure holding.

Is this answer helpful?

A

Yes the drill includes a depth stop feature. You can set the desired drilling depth manually using the stop mechanism on the auxiliary handle to ensure consistent results on your workpiece.

Is this answer helpful?

A

Always wear eye protection when operating the tool. It is also recommended to wear hearing protection especially during impact drilling. Use dust masks when working with materials that create harmful dust.

Is this answer helpful?

A

No the dust box is intended for concrete and stone drilling. Using it for metal work is dangerous because hot metal chips can ignite parts of the dust box causing a fire hazard.

Is this answer helpful?

A

There is a rotational direction switch on the tool. Push it to the left for right rotation or to the right for left rotation. Do this only when the tool is switched off to prevent damage.

Is this answer helpful?

A

The electronic control helps maintain speed under load. If the tool jams the switch turns off immediately on kickback control models. Allow the tool to cool down if used for long periods at low speeds.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Versatile for drilling masonry wood and metal
  • Keyless chuck for quick bit changes
  • Variable speed control with trigger
  • Ergonomic handle for better control
  • Includes Drill Assistant dust management
VS

Disadvantages

  • Vibration levels are high during impact drilling
  • Noise levels require ear protection
  • Dust box has limited capacity
  • Weight increases with drill assistant
  • Requires specific voltage compatibility
M: QW-35-FL

Product Specification

Type

Hammer Drill

Power

700 W

No-load Speed

50-3,000 RPM

No-load Impact Rate

45,000 BPM

Drilling Capacity

Wood 1.18 in, Steel 0.47 in, Concrete 0.55 in

Torque

12.54 ft-lb

Chuck

0.08-0.51 inch Keyless Chuck

M: QW-35-FL

Product Description

The Bosch DIY UniversalImpact 700 Electric Impact Drill Manual Experience

When tackling home improvement projects, having a reliable power tool is essential for success. The Bosch DIY UniversalImpact 700 Electric Impact Drill is designed for versatility and durability. It handles everything from drilling masonry to driving screws in wood or metal. This tool combines significant power and precision for the serious do-it-yourself enthusiast looking for quality results in their household or garden repairs.

Key Features and Performance

The 700 Watt motor provides ample torque for tough jobs like driving large screws or boring into concrete walls. You can adjust the speed to match the specific material you are working with using the thumbwheel. Whether you are boring into hard brick or softwood, the variable trigger allows for precise control over the operation. The keyless chuck makes changing bits quick and easy which saves time and frustration.

Comfort and Safety Design

Holding the tool securely is important for safety and accuracy on the job site. The ergonomic auxiliary handle helps maintain balance and control during extended use for large drills. Some models include a Drill Assistant attachment for dust extraction. This keeps your workspace clean and reduces health risks from airborne particles. Always wear eye protection and follow all safety guidelines to ensure a safe working environment while operating this machine.

Versatility in Action

This drill is not just for making holes in the wall or floor. You can use it for screwdriving when switched to the rotation mode properly. The electronic control ensures constant speed under load so the motor does not stall when working against resistance. The reverse function helps remove stuck screws easily without damaging the workpiece or stripping heads. Proper maintenance ensures consistent performance over many years of active use.

Important Notes for Users

Keep the tool maintained regularly by clearing dust from vents to prevent overheating. Check cords for damage before every use to prevent electrical hazards or shocks. Avoid operating in wet conditions or heavy rain for safety. Store the tool in a dry place when not in use. Regular cleaning of vents ensures longevity and prevents overheating during heavy projects around the home.

Additional features include a depth stop for consistent hole depths and a dust box for clean drilling. These add-ons help you achieve professional results without unnecessary mess or errors in your measurements during construction work.

Technical Specifications Overview

Understanding the technical details helps you choose the right setup for your project effectively. The machine operates at standard voltage levels suitable for most European outlets. It supports a range of drill bits up to specific diameters for masonry and metal. Knowing these limits prevents damage to the drill or the material being worked on during heavy duty tasks.

M: QW-35-FL

© Copyright 2026 Manual.ly