Manual.ly Logo

Bosch DIY PKS 16 Multi Manual

4.3 · 11 Ratings

PDF manual · 118 Pages

English

M: OA-GPT-54-NAN
page

/ 118

Loading...
d0a1aeafd3ac5531b5837d4ca3340f2c6da0 page 16
22 | English
1 609 92A 216 | (16.6.16) Bosch Power Tools
Working with an Auxiliary Stop (see figure E)
For sawing large workpieces or straight edges, a board or lath
can be fastened to the workpiece as an auxiliary stop, and the
power tool can be guided by its base plate alongside the aux-
iliary stop.
Cutting Marks (see figure E)
The “CutControl” viewing window 7, which folds out to the
front, is used for precise guiding of the power tool alongside
the cutting line on the workpiece.
The cutting mark 19 indicates the position of the application
tool for right-angled cuts.
For a dimensionally accurate cut, position the power tool
against the workpiece as shown in the figure. It is recom-
mended to carry out a test cut.
Plunge Cuts (see figure D)
The marks on the base plate indicate the cutting edge on the
workpiece at maximum cutting depth.
– Place the base plate 3 on the working surface. Make sure
that the rear mark on base plate 3 corresponds with the
beginning of the cutting line.
– Switch the power tool on and wait until the saw blade 14
has reached its operating speed.
– Plunge the saw blade 14 slowly into the workpiece. Plung-
ing in too quickly can lead to kickback. Guide the machine
alongside the cutting line. Do not pull the machine toward
the rear!
– When reaching the end of the cutting line, lift the power
tool from the workpiece, and leave it switched on for a few
seconds.
Maintenance and Service
Maintenance and Cleaning
Before any work on the machine itself, pull the mains
plug.
For safe and proper working, always keep the machine
and ventilation slots clean.
If the replacement of the supply cord is necessary, this has to
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.
The blade guard 6 must always move freely and retract auto-
matically. Therefore, always keep the area around the blade
guard 6 clean. Remove dust and chips/shavings using a brush
or by blowing out with compressed air.
Saw blades that are not coated can be protected against cor-
rosion with a thin coat of acid-free oil. Before use, the oil must
be removed again, otherwise the wood will become soiled.
Resin and glue residue on the saw blade produces poor cuts.
Therefore, clean the saw blade immediately after use.
After finishing work, dismount the clamping fixtures and clean
all clamping parts as well as the protective cover.
After-sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Bosch’s application service team will gladly answer questions
concerning our products and their accessories.
In all correspondence and spare parts order, please always in-
clude the 10-digit article number given on the type plate of
the machine.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschse[email protected]
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: (01) 4666700
Fax: (01) 4666888
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: (01300) 307044
Fax: (01300) 307045
Inside New Zealand:
Phone: (0800) 543353
Fax: (0800) 428570
Outside AU and NZ:
Phone: +61 3 95415555
www.bosch.com.au
Republic of South Africa
Customer service
Hotline: (011) 6519600
Gauteng – BSC Service Centre
35 Roper Street, New Centre
Johannesburg
Tel.: (011) 4939375
Fax: (011) 4930126
OBJ_BUCH-1837-005.book Page 22 Thursday, June 16, 2016 11:13 AM

Chat with your Bosch DIY PKS 16 Multi manual using AI

Get instant AI answers from your Bosch DIY PKS 16 Multi manual

Ask anything about the Bosch DIY PKS 16 Multi. Answers come from this manual, with the pages they are based on.

PKS 16 Multi Maintenance Schedule

Before each use
Check guard function

Verify the blade guard closes properly and moves freely. Do not operate if it does not close instantly or is stuck.

Show in the manual (page 16)
Before each use
Check guard spring

Inspect the guard return spring condition and operation. Service if the guard operates sluggishly due to debris or damage.

Show in the manual (page 16)
After every use
Clean ventilation slots

Keep machine and air vents clean by removing dust and chips with a brush or compressed air to prevent electrical hazards.

Show in the manual (page 22)
After every use
Clean saw blade and parts

Remove resin and glue residue from the blade immediately after use. Clean all clamping parts and the protective cover after finishing work.

Show in the manual (page 22)
M: QW-35-FL

Ask a Question

0/1000

Do you recommend PKS 16 Multi?

Yes No
0
User Pic

Lea Zimmermann

8 months ago

Does the Bosch PKS16 Multi have a clear marking/indicator to see exactly where the cut starts and ends? I often need precise cut lines when trimming boards or tiles.

0
User Pic

Manual.ly

8 months ago

The PKS16 Multi does not provide a highly visible, full-length scale for the exact start and end of the cut. In practice, the most reliable method is to mark the cut line on your workpiece (pencil/tape) and align the saw base and blade to that line before cutting. If you need better guidance, you can also use a straight edge/guide and measure your required cut length to set the start position. Several users also note that visibility of the cut end can be limited, especially when trying to stop at a specific point.

M: OA-GPT-5-NAN
M: OA-GPT-5-NAN

Frequently Asked Questions

A

It is designed for wood, thin non-ferrous metals, plastics, and tiles when fitted with the correct diamond cutting disc. Ferrous metals are not permitted.

Is this answer helpful?

A

Yes, but only with an approved diamond cutting disc. The manual specifies dry cutting with dust extraction, so it is important to use the right setup.

Is this answer helpful?

A

The tool has a 400 W rated power input. That makes it a compact DIY saw suited to lighter household cutting jobs rather than heavy construction work.

Is this answer helpful?

A

Yes, the product is described as including a case, which makes storage and transport more convenient for home users and occasional workshop tasks.

Is this answer helpful?

A

Yes, the cutting depth is adjustable. This helps match the cut to the thickness of the material and improves safety and control during operation.

Is this answer helpful?

A

Yes. Dust extraction is strongly recommended for wood, plastic, and especially stone materials. It helps keep the workspace cleaner and reduces health risks.

Is this answer helpful?

M: OA-GPT-54-NAN

Advantages and Disadvantages

Advantages

  • Compact and lightweight, making it easy to control during DIY cutting tasks.
  • Works with wood, plastics, thin non-ferrous metals, and tiles using the right blade.
  • Adjustable cutting depth supports cleaner, more accurate results.
  • Includes a case for easier storage and transport.
  • Cut line viewing support helps improve guidance along marked cuts.
VS

Disadvantages

  • Not intended for ferrous metals, so its material range is limited.
  • 400 W output is best for light to medium DIY work, not demanding site tasks.
  • Blade changes and setup require care to follow the manual correctly.
  • Tile cutting is limited to dry cutting with dust extraction.
M: OA-GPT-54-NAN

Product Specification

Type

Circular Saw

Power

400W

No-load Speed

6400/min

Saw Blade Diameter

2.56 in

Cutting Capacity

0.63 in (cutting depth at 0°)

Tool Holder

Bore 0.59 in, Spindle Lock

Features

Softgrip, Dust Extraction

Weight

4.19 lb

Scope of Delivery

Case, 3-piece accessory set

M: OA-GPT-54-NAN

Product Description

Bosch DIY PKS 16 Multi electric circular saw incl. case Manual

The Bosch DIY PKS 16 Multi is a compact circular saw designed for home projects that need clean, controlled cuts without the bulk of a full-size machine. Its 400 W motor and lightweight 1.9 kg build make it easy to handle, especially when working on shelves, panels, trim, or tile repair tasks around the house. Supplied with a case, it is a practical choice for users who want a portable saw that stores neatly and travels well between jobs.

One of the most appealing points is its versatility. With the right blade, the saw can handle wood, thin non-ferrous metals, and plastics, while a diamond cutting disc opens the door to dry tile cutting. That flexibility means one tool can support several common DIY projects. The adjustable cutting depth also helps improve accuracy, allowing you to match the cut more closely to the material thickness and reduce waste.

Bosch has clearly focused on ease of control. The viewing window for the cut line, combined with the compact base plate, helps guide the tool along a marked path. For straight cuts, an auxiliary stop can improve precision even further. The plunge-style operation adds another layer of convenience, making it easier to start cuts in a controlled way when the task calls for it.

Safety and maintenance are also central to the design. The guard is built to close automatically, and the tool includes a lock-off button to reduce accidental starts. Dust extraction support is especially useful when cutting wood, plastic, or stone materials, since it helps keep the workspace cleaner and visibility better. The manual also stresses the importance of using the correct blade type, keeping the saw clean, and working with proper workpiece support.

For DIY users who want a small but capable saw, the Bosch DIY PKS 16 Multi electric circular saw incl. case Manual highlights a tool that balances portability, precision, and multi-material performance. It is not a heavy-duty site saw, but for careful home use it offers a thoughtful mix of functionality and convenience.

Notes

  • Best suited for straight cuts in wood, plastics, and thin non-ferrous metals.
  • Diamond discs are intended for dry tile cutting only.
  • Use dust extraction whenever possible for cleaner and safer work.
  • Ferrous metal cutting is not permitted.
M: OA-GPT-54-NAN

© Copyright 2026 Manual.ly