Manual.ly Logo

Benning MM 3 Manual

5.0 · 1 Ratings

PDF manual · 127 Pages

English

M: OA-GPT-54-NAN
page

/ 127

Loading...
187f97834813dacfd344cb39484d3eebd751 page 16
09/ 2013
BENNING MM 3
14
7.5 Resistance ranges
Overload protection for resistance measurements: 600 V
rms
.
Range
Resolution
Accuracy
Maximum
test current
Max. open
circuit voltage
200 Ω 0,1 Ω ± (0.8 % of reading + 4 digits) 2,5 mA 3,2 V
2 kΩ 1 Ω ± (0.8 % of reading + 2 digits) 200 µA 0,5 V
20 kΩ 10 Ω ± (0.8 % of reading + 2 digits) 40 µA 0,5 V
200 kΩ 100 Ω ± (0.8 % of reading + 2 digits) 4 µA 0,5 V
2 MΩ 1 kΩ ± (0.8 % of reading + 2 digits) 400 nA 0,5 V
20 MΩ 10 kΩ ± (2 % of reading + 5 digits) 40 nA 0,5 V
7.6 Diode and Continuity Testing
The accuracy indicated below is valid in the range of 0.4 V to 0.9 V.
Overload protection for diode testing: 600 V
rms
.
The built-in buzzer sounds if the resistance R falls below 50 Ω.
Range
Resolution
Accuracy
Maximum
test current
Max. open
circuit voltage
1 mV ± (1,5 % of reading + 5 digits) 1,5 mA 3,2 V
7.7 Capacitance ranges
Conditions: Capacitors must be discharged before testing and then connected
to the meter according to the indicated polarity.
Range
Resolution
Accuracy
Frequency
2 nF 1 pF ± (2,0 % of reading + 4 digits) 40 Hz
20 nF 10 pF ± (2,0 % of reading + 4 digits) 40 Hz
200 nF 100 pF ± (2,0 % of reading + 4 digits) 40 Hz
2 µF 1 nF ± (2,0 % of reading + 4 digits) 40 Hz
20 µF 10 nF ± (2,0 % of reading + 4 digits) 40 Hz
200 µF 100 nF ± (2,0 % of reading + 4 digits) 40 Hz
7.8 Frequency ranges
The frequency to be measured must have a minimum input signal of 200 mV
rms
.
Range Resolution
Accuracy
for 5 V
rms
max.
Minimum input
frequency
Overload
protection
2 kHz 1 Hz ± (1,0 % of reading + 3 digits) 20 Hz 600 V
rms
20 kHz 10 Hz ± (1,0 % of reading + 3 digits) 200 Hz 600 V
rms
200 kHz 100 Hz ± (1,0 % of reading + 3 digits) 2 kHz 600 V
rms
8. Measuring with BENNING MM 3
8.1 Measurement preparation
The BENNING MM 3 must be used and stored only at the indicated storage and
working temperatures, avoid exposure to continuous sunlight.
- Check the rated voltage and current indications on the test leads. The
safety test leads provided with the BENNING MM 3 correspond specifically
to the rated voltage and current of the BENNING MM 3.
- Inspect the test leads for damaged insulation. If the insulation is damaged,
the test leads should be discarded immediately.
- Check test lead continuity. If the conductor in the test lead is damaged, the
leads should be discarded immediately.
- Remove test leads from circuit to be measured before turning the rotary
switch to select another function.
- If the BENNING MM 3 is used near strong noise generating sources, the
display may become unstable and measurement errors may arise.

Chat with your Benning MM 3 manual using AI

Get instant AI answers from your Benning MM 3 manual

Ask anything about the Benning MM 3. Answers come from this manual, with the pages they are based on.

MM 3 Maintenance Schedule

Remind me when maintenance is due
Yearly
Calibrate the multimeter

Send the device to the factory service center once a year to maintain specified measurement accuracy.

Show in the manual (page 16)
As needed
Replace the battery

Change the 9 V battery when the low battery symbol appears on the display.

Show in the manual (page 15)
As needed
Replace the fuses

Replace the 1 A and 16 A fuses if they blow due to overload protection activation.

Show in the manual (page 15)
As needed
Inspect test leads

Check test leads for damaged insulation or broken conductors before each use and discard if damaged.

Show in the manual (page 22)

Free maintenance reminders

Timed to your purchase date. Always free, unsubscribe anytime.

By submitting you agree to the privacy policy. Unsubscribe with one click in any email.
M: QW-35-FL

Ask a Question

0/1000

Do you recommend MM 3?

Yes No
0
User Pic

autem_est

9 months ago

How fast is the shipping and order processing? Is the handling straightforward and do I get tracking?

0
User Pic

Manual.ly

9 months ago

We aim for quick, uncomplicated processing. After your order is placed, it is prepared and handed to the carrier promptly, and you will receive a confirmation email with tracking details once it ships. Delivery times can vary slightly depending on your location and the carrier, but you can follow the shipment in the tracking link throughout the journey.

M: OA-GPT-5-NAN
M: OA-GPT-5-NAN

Frequently Asked Questions

A

It measures DC and AC voltage, DC and AC current, resistance, diode condition, continuity, capacitance, and frequency. That makes it useful for general electrical troubleshooting and basic component checks.

Is this answer helpful?

A

Yes, it is aimed at electricians and electrically trained users. Its safety ratings, fuses, and practical measurement ranges make it well suited to routine service and maintenance tasks.

Is this answer helpful?

A

Yes. The Benning MM 3 switches off automatically after about 30 minutes. This helps save battery life when the meter is left idle between measurements.

Is this answer helpful?

A

It uses a 9 V block battery. A low-battery symbol appears on the display when the voltage drops too far, so you know when replacement is needed.

Is this answer helpful?

A

Yes, but only after the capacitor has been fully discharged. You should never apply voltage to the capacitance input terminals, as this could damage the meter.

Is this answer helpful?

A

The continuity mode checks whether a circuit path is intact. If resistance drops below about 50 ohms, the built-in buzzer sounds, making fault tracing faster.

Is this answer helpful?

A

Yes. It includes built-in fast-blow fuses for the current inputs and is designed with category-based protection limits. Using the correct leads and settings is still essential.

Is this answer helpful?

M: OA-GPT-54-NAN

Advantages and Disadvantages

Advantages

  • Covers voltage, current, resistance, diode, continuity, capacitance, and frequency testing in one compact meter.
  • Clear 3½-digit LCD and automatic polarity help make readings quick and easy to interpret.
  • Protective rubber holster improves durability and allows standing or hanging during use.
  • Built-in fuses, safety leads, and category-rated protection support safer everyday electrical work.
VS

Disadvantages

  • Designed for dry environments only, so it is not suitable for damp or wet job sites.
  • The 20 A current range is limited to short measurements, which reduces heavy-duty testing flexibility.
  • Accuracy and functionality are practical rather than advanced, so it may not suit specialized lab work.
  • Capacitance testing requires fully discharged capacitors, adding an extra preparation step.
M: OA-GPT-54-NAN

Product Specification

Measurement Range

max. 20A, max. 600V, max. 20MΩ

Package Contents

Bag, Test leads

M: OA-GPT-54-NAN

Product Description

Benning MM 3 Multimeter: A Reliable Everyday Tester

The Benning MM 3 Multimeter is built for practical electrical work where dependable readings and straightforward control matter most. It combines the core functions technicians reach for daily with a compact, rugged design that feels ready for the workshop, service van, or bench. If you are searching for the Benning MM 3 Multimeter Manual, this overview highlights what the instrument is designed to do and why it remains useful for routine diagnostics.

At its heart, the MM 3 is a 3½-digit digital multimeter with clear measurement handling and automatic polarity indication. It covers DC and AC voltage, DC and AC current, resistance, diode testing, continuity checks with an audible buzzer, capacitance, and frequency. That broad range makes it a versatile tool for checking power supplies, tracing faults in circuits, testing components, and verifying signal behavior without switching between multiple devices.

One of its strengths is simplicity. The rotary selector makes mode changes easy, while the display shows values clearly and flags overload conditions. The meter also includes an automatic shutdown function after roughly 30 minutes, helping preserve battery life during busy work sessions. A 9 V battery powers the unit, and the low-battery symbol gives a timely warning before readings become unreliable.

Safety is a major part of the MM 3’s appeal. It is designed for dry environments and supports typical categories used in electrical testing, with protective fuses and supplied safety leads included. The rubber holster adds impact protection and also lets the meter stand upright or hang in place for easier viewing. For field work, that small detail can make a big difference.

The instrument is not overloaded with complex features, and that is part of its value. Instead of trying to be everything at once, it focuses on essential test modes, solid handling, and practical protection. For electricians, maintenance staff, and technically trained users, the Benning MM 3 offers a balanced mix of functionality and durability.

Notes

  • Best suited for dry, controlled measuring environments.
  • Use only proper safety leads and caps for higher measurement categories.
  • Capacitors should be fully discharged before capacitance testing.
  • Regular calibration helps maintain the stated accuracy.
M: OA-GPT-54-NAN

© Copyright 2026 Manual.ly