Manual.ly Logo

Benning MM 10-1 Manual

5.0 · 1 Ratings

PDF manual · 78 Pages

English

M: QW-35-FL
page

/ 78

Loading...
1194e07ef0c87ddf16782b3d4f464305d311 page 2a
42
03/ 2020
BENNING MM 10 –PV/ MM 10 –1
9.1 Securing the device
Under certain circumstances, safe operation of the BENNING MM 10-PV/
MM 10-1 might no longer be ensured, e.g. in case of:
- visible damage of the housing,
- incorrect measuring results,
- recognizable consequences of prolonged storage under inadmissible condi-
tions and
- recognizable consequences of extraordinary stress due to transport.
In such cases, immediately switch o󰀨 the BENNING MM 10-PV/ MM 10-1, dis-
connect it from the measuring points and secure it against further use.
9.2 Cleaning
Clean the exterior of the device with a clean dry cloth (exception: special cleaning
wipers). Do not use any solvents and/or abrasives to clean the device. Make sure
that the battery compartment and the battery contacts are not contaminated by
leaking battery electrolyte.
If there are electrolyte contamination or white deposits in the area of the battery
or the battery compartment, clean these areas as well by means of a dry cloth.
9.3 Battery replacement
Before opening the BENNING MM 10-PV/ MM 10-1, strictly
observe that the device is free of voltage!
Electrical danger!
The BENNING MM 10-PV/ MM 10-1 is supplied by means of two integrated 1.5 V
batteries (AA/ IEC LR6). Battery replacement (see g. 10) is required as soon as
all segments of the battery symbol
3
on the digital display
1
have disappeared
and the battery symbol is ashing.
Proceed as follows to replace the battery:
- Disconnect the safety measuring leads from the measuring circuit.
- Remove the safety measuring leads from the BENNING MM 10-PV/
MM 10-1.
- Turn the rotary switch
9
to the switch setting “OFF”.
- Remove the protective rubber holster
M
from the BENNING MM 10-PV/
MM 10-1.
- Lay the BENNING MM 10-PV/ MM 10-1 face down and release the screws
of the battery compartment cover.
- Lift the battery compartment cover to remove it from the housing.
- Remove the discharged batteries from the battery compartment.
- Insert the new batteries into the battery compartment observing correct po-
larity.
- Place the battery compartment cover onto the bottom part and tighten the
screw.
- Replace the BENNING MM 10-PV/ MM 10-1 in its protective rubber holster
M
.
See g. 10: Battery replacement
Make your contribution for environmental protection! Do not
dispose of discharged batteries via the household waste. In-
stead, return them to a collecting point for discharged batteries
or spezial waste. Please look for information in your commu-
nity‘s facilities.
9.4 Fuse replacement
Before opening the BENNING MM 10-PV/ MM 10-1, strictly
observe that the device is free of voltage!
Electrical danger!
The BENNING MM 10-PV is protected against overload by means of an inte-
grated fuse (G melt insert) 11 A rapid and the BENNING MM 10-1 is protected
against overload by means of an integrated fuse (G melt insert) 440 mA rapid
(see gure 11).
Proceed as follows to replace the fuse:
- Disconnect the safety measuring leads from the measurement circuit.
- Disconnect the safety measuring leads from the BENNING MM 10-PV/
MM 10-1.
- Turn the rotating switch
9
to the “OFF” position.
- Remove the protective rubber holster
M
from the BENNING MM 10-PV/
MM 10-1.
- Lay the BENNING MM 10-PV/ MM 10-1 face down and release the screws

Chat with your Benning MM 10-1 manual using AI

Get instant AI answers from your Benning MM 10-1 manual

Ask anything about the Benning MM 10-1. Answers come from this manual, with the pages they are based on.

MM 10-1 Maintenance Schedule

Remind me when maintenance is due
Yearly
Calibrate the multimeter

Send the device to Benning factory service for recalibration to maintain specified measurement accuracy.

Show in the manual (page 43)
Regularly
Clean the device housing

Wipe the exterior with a clean dry cloth. Do not use solvents or abrasives. Ensure battery contacts are free of electrolyte contamination.

Show in the manual (page 42)

Free maintenance reminders

Timed to your purchase date. Always free, unsubscribe anytime.

By submitting you agree to the privacy policy. Unsubscribe with one click in any email.
M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend MM 10-1?

Yes No
0
User Pic

Deanna Jacobi

6 months ago

How does the mobile phone function work and is it easy to use?

0
User Pic

Manual.ly

6 months ago

The mobile phone function is designed for seamless integration with your smartphone, allowing you to control the product remotely via our dedicated app. It features an intuitive interface that makes setup quick and usage straightforward for all users.

M: QW-35-FL
M: QW-35-FL
0
User Pic

Sara Kowalski

5 months ago

Does the mobile connectivity feature support both iOS and Android devices?

M: QW-35-FL

Frequently Asked Questions

A

The device is rated for up to 1000 V AC/DC in Category III and 600 V AC/DC in Category IV. When using the optional TA PV adapter with the MM 10-PV model, it can measure up to 2000 V DC.

Is this answer helpful?

A

Yes, the Benning MM 10-1 features a Bluetooth 4.0 interface. You can download the BENNING MM-CM Link app on Android or iOS devices to view real-time data and download logged measurements.

Is this answer helpful?

A

Select the continuity symbol on the rotary switch. Press the blue function key to activate the buzzer and LED. Touch the probes to the component; if resistance is below 200 ohms, the buzzer sounds and the LED lights up.

Is this answer helpful?

A

When the battery is depleted, the battery symbol on the display will blink. You should replace the two AA batteries immediately to avoid inaccurate readings or device failure.

Is this answer helpful?

A

No, the Benning MM 10-1 has an IP30 rating which means it offers no protection against water. It is designed for use only in dry indoor environments.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • True RMS measurement ensures accuracy with non-sinusoidal signals
  • High safety rating of CAT III 1000V and CAT IV 600V
  • Bluetooth connectivity allows wireless data transfer to mobile devices
  • AutoV/LoZ function simplifies voltage detection and range selection
  • Durable rubber housing protects against drops and impacts
VS

Disadvantages

  • Battery life may decrease significantly when using Bluetooth or backlight
  • Requires specific BENNING TA PV adapter for high voltage PV measurements
  • Limited to dry environments due to IP30 protection rating
  • Manual must be consulted for fuse replacement procedures
  • No water resistance makes it unsuitable for wet outdoor conditions
M: QW-35-FL

Product Specification

Measurement range

max. 0.4A, max. 1000V, 40MΩ

Package contents

Case, test leads, wire temperature sensor, battery

M: QW-35-FL

Product Description

Benning MM 10-1 Multimeter: Precision and Safety for Professionals

The Benning MM 10-1 Multimeter represents a significant leap in electrical measurement technology, designed specifically for skilled electricians and electrotechnically trained personnel. This robust device combines high accuracy with essential safety features, making it an indispensable tool for modern electrical diagnostics. Whether you are troubleshooting complex circuits or performing routine maintenance, the MM 10-1 delivers reliable results in dry environments.

Equipped with True RMS technology, this multimeter ensures precise readings even when dealing with non-sinusoidal waveforms common in today's electronic equipment. The device supports a wide range of measurements including direct and alternating voltage, current, resistance, frequency, and temperature. Its intelligent AutoV/LoZ function automatically detects the type of voltage and selects the optimal range, reducing user error and streamlining the testing process. The low input impedance effectively suppresses capacitive and inductive voltages, providing clearer signals in noisy environments.

Safety is paramount with the Benning MM 10-1. It meets strict CAT III 1000V and CAT IV 600V standards, ensuring protection against dangerous overvoltages. The unit features a durable rubber protective frame that safeguards the device from mechanical damage and allows it to stand upright during use. An integrated magnet enables hands-free operation by attaching the meter to metal surfaces. For those needing data tracking, the built-in Bluetooth interface connects seamlessly to smartphones and tablets via the BENNING MM-CM Link app, allowing for real-time monitoring and storage of up to 4000 measured values.

Key Features and Benefits

The Benning MM 10-1 stands out for its versatility and ease of use. The digital display offers a clear view of measurements with a bar graph for quick visual reference. Users can toggle between Celsius and Fahrenheit for temperature readings using the included Type K sensor. The device also includes a MIN/MAX function to capture peak values and a relative mode for offset measurements. Maintenance is straightforward with easy access to replaceable batteries and fuses, ensuring long-term reliability. Always remember to follow safety protocols, such as checking leads for damage before use and wearing appropriate personal protective equipment when working with live circuits.

Important Notes

  • Always verify the insulation of measuring leads before use.
  • Do not exceed the maximum rated voltage for your specific circuit category.
  • Replace batteries immediately if the indicator flashes to prevent measurement errors.
  • Ensure the device is powered off before changing fuses or batteries.
M: QW-35-FL

© Copyright 2026 Manual.ly