Manual.ly Logo

Benning IT 105 Manual

4.0 · 1 Ratings

PDF manual · 79 Pages

English

M: OA-GPT-5-NAN
page

/ 79

Loading...
6c854f71921ab3e7193bc3eba854d5c2d991 page 14
04/ 2020
BENNING IT 105
13
D
Bei der Prüfung selektiver Fehlerstromschutzeinrichtungen startet die Messung nach einer Zeitverzögerung
von 30 s.
►
►
►
I∆N Nennfehlerstrom (F4):
Über die Funktionstaste F4 können Sie den Nennfehlerstrom anwählen:
Nennfehlerstrom bei RCD-Typ AC :
10 mA
►
30 mA
►
100 mA
►
300mA
►
500 mA
- Messleitungen gemäß Bild 4 oder 5 am BENNING IT 105 an schließen und mit dem Prüfobjekt kontak-
tieren.
- Betätigen Sie die TEST-Taste
4
, um die Messung zu starten.
- Das Hauptdisplay K zeigt den gemessenen Auslösestrom an.
9. Instandhaltung
Vor dem Öffnen das BENNING IT 105 unbedingt span nungsfrei machen! Elektrische Gefahr!
Die Arbeit am geöffneten BENNING IT 105 unter Spannung ist ausschließlich Elektrofachkräften vorbe-
halten, die dabei besondere Maßnahmen zur Unfallverhütung treffen müssen.
So machen Sie das BENNING IT 105 spannungsfrei, bevor Sie das Gerät öffnen:
- Schalten Sie das Prüfgerät aus
- Trennen Sie alle Anschlussleitungen vom Gerät
9.1 Sicherstellen des Gerätes
Unter bestimmten Voraussetzungen kann die Sicherheit im Umgang mit dem BENNING IT 105 nicht mehr
gewährleistet sein; zum Beispiel bei:
- Sichtbaren Schäden am Gehäuse,
- Fehlern bei Messungen,
- Erkennbaren Folgen von längerer Lagerung unter unzulässigen Bedingungen und
- Erkennbaren Folgen von außerordentlicher Trans port be an spruchung.
In diesen Fällen ist das BENNING IT 105 sofort abzuschalten, von den Prüfstellen zu entfernen und gegen
erneute Nutzung zu sichern.
9.2 Reinigung
Reinigen Sie das Gehäuse äußerlich mit einem sauberen und trockenen Tuch (Ausnahme spezielle
Reinigungstücher). Verwenden Sie keine Lösungs- und/oder Scheuermittel, um das Gerät zu reinigen.
Achten Sie unbedingt darauf, dass das Batteriefach und die Batteriekontakte nicht durch auslaufendes
Batterie-Elektrolyt verunreinigt werden.
Falls Elektrolytverunreinigungen oder weiße Ablagerungen im Bereich der Batterie oder des Batteriegehäuses
vorhanden sind, reinigen Sie auch diese mit einem trockenen Tuch.
9.3 Batteriewechsel
Vor dem Öffnen das BENNING IT 105 unbedingt span nungsfrei machen! Elektrische Gefahr!
Das BENNING IT 105 wird durch sechs 1,5 V-Mignon-Batterien/Typ AA (IEC LR6) gespeist.
Ein Batteriewechsel ist erforderlich, wenn in der Anzeige das Batteriesymbol I blinkt.
So wechseln Sie die Batterien (siehe Bild 8):
- Schalten Sie das BENNING IT 105 aus.
- Legen Sie das BENNING IT 105 auf die Frontseite und lösen Sie die Schrauben vom Batteriedeckel.
- Heben Sie den Batteriedeckel vom Unterteil ab.
- Heben Sie die entladenen Batterien aus dem Batteriefach.
- Legen Sie dann die Batterien in die dafür vorgesehenen Stellen im Batteriefach (achten Sie bitte unbe-

Chat with your Benning IT 105 manual using AI

Get instant AI answers from your Benning IT 105 manual

Ask anything about the Benning IT 105. Answers come from this manual, with the pages they are based on.

IT 105 Maintenance Schedule

Remind me when maintenance is due
Yearly
Calibrate the tester

Send the device to the Benning service center annually to maintain specified accuracy.

Show in the manual (page 21)
When indicated
Replace batteries

Replace all six batteries immediately when the battery symbol flashes on the display.

Show in the manual (page 20)
When indicated
Replace fuse

Replace the internal fuse only if the defective fuse symbol appears or after overload.

Show in the manual (page 21)
Regularly
Clean the housing

Wipe the exterior with a clean dry cloth. Do not use solvents or abrasives.

Show in the manual (page 10)

Free maintenance reminders

Timed to your purchase date. Always free, unsubscribe anytime.

By submitting you agree to the privacy policy. Unsubscribe with one click in any email.
M: QW-35-FL

Ask a Question

0/1000

Do you recommend IT 105?

Yes No
0
User Pic

Rosie Wood

8 months ago

Is this product solidly built, and does it come with good accessories?

0
User Pic

Manual.ly

8 months ago

Customers describe the device as having solid, well-finished workmanship and note that the included accessories are good. For the exact scope, please compare the package contents listed on the product page, since accessory sets can vary by bundle and region.

M: OA-GPT-5-NAN
M: OA-GPT-5-NAN

Frequently Asked Questions

A

The IT 105 measures voltage and frequency, phase sequence, insulation resistance (250/500/1000 V), low-resistance continuity (RLOW, 200 mA), loop/line impedance (ZS/ZI) in NO-TRIP and HIGH CURRENT modes, and RCD tripping time and trip current (RCDt, RCDI).

Is this answer helpful?

A

Yes. It supports automatic RCD tripping sequences (AUTO) and manual modes (½×, 1×, 5× IΔN) with selectable polarity and waveform (AC or pulsed Type A). The main display shows measured trip time and the unit monitors PE contact voltage, blocking tests if unsafe levels (>50 V) are detected.

Is this answer helpful?

A

Use the NO-TRIP mode which applies a low test current to usually avoid upstream RCD tripping. If residual fault currents exist the RCD can still trip; in that case retry or use measurement methods according to safety procedures.

Is this answer helpful?

A

The device is for dry environments (IP40) and operation between 0 °C and 40 °C, up to 2000 m elevation. Only qualified personnel should use it; observe CAT III limitations (max 300 V conductor to earth) and use supplied CAT-rated accessories for category III measurements.

Is this answer helpful?

A

It uses six AA (IEC LR6) batteries. The instrument indicates low battery on the display. Replace batteries when the battery symbol flashes. It contains a replaceable fuse (1.6 A, 1000 V FF). Regular cleaning and an annual factory calibration are recommended to maintain accuracy.

Is this answer helpful?

A

Included: tester, transport case, test probe with TEST key, test cable with shock-proof plug, measuring leads/alligator clips, 4 mm adapter, carrying strap, six AA batteries, fuse and calibration certificate. Optional: long measuring leads with reel (e.g., BENNING TA5 40 m) for protective conductor measurements.

Is this answer helpful?

A

Accuracy depends on function: voltage ±(5%+2 digits) up to 440 V; continuity RLOW ±(2%+5 digits); insulation RISO ±(5%+5 digits); loop/line impedance ZS/ZI ±(5%+5 digits) with finer resolution ranges; RCD times ±(5%+2 digits). Calibrate annually to keep specifications.

Is this answer helpful?

M: OA-GPT-5-NAN

Advantages and Disadvantages

Advantages

  • Comprehensive multifunction tester: voltage, RISO (250/500/1000 V), RLOW, ZS/ZI, RCDt/RCDI.
  • Clear backlit display with function keys, LOCK/AUTO features and TEST probe for easy operation.
  • Calculates prospective fault current (PFC) and short-circuit current (PSC) for protection assessment.
  • Meets IEC/EN safety and EMC standards; includes overload fuse and PE contact-voltage monitoring.
  • Supplied complete with leads, test cable, probe, 4 mm adapter, case, batteries and calibration certificate.
VS

Disadvantages

  • Not intended for wet environments (IP40) — limited water protection.
  • High-current loop tests can trip upstream RCDs and require care during measurement.
  • Battery-powered (six AA) — frequent field use requires spare batteries and periodic replacement.
  • Fuse replacement and deeper repairs require qualified service; user-accessible repairs limited.
  • Maximum safe measurement category limits (CAT III up to 300 V to earth) — observe limitations.
M: OA-GPT-5-NAN

Product Description

BENNING IT 105 Installation Tester

The BENNING IT 105 is a compact, multifunctional installation tester designed for electrical safety verification in accordance with IEC 60364-6 and EN 50110. Built for field technicians and qualified personnel, the tester provides a wide range of measurements including voltage, frequency, phase sequence, insulation resistance (RISO) at selectable test voltages (250/500/1000 V), low-resistance continuity (RLOW) with 200 mA test current, RCD timing and trip-current tests (RCDt, RCDI), and loop/line impedance (ZS/ZI) measurements with both low (NO-TRIP) and high (HIGH CURRENT) test currents. It also calculates prospective fault current (PFC) and short-circuit current (PSC) for assessing protective device operation.

Key product details

The tester features a clear backlit digital display with main and sub-displays for measured values, progress and status icons, and dedicated function keys (F1–F4) plus a TEST key for direct operation. A rotary function selector selects measurement modes including V, RISO (three voltages), RLOW, ZS/ZI (HIGH CURRENT and NO-TRIP), and multiple RCD test modes (AUTO, x½, x1, x5, ramp). The device monitors mains connection and contact voltage on PE to protect users during RCD testing and indicates overheating, low battery, or blown fuse conditions.

Ergonomically packaged, the BENNING IT 105 is delivered with measuring leads (black/blue/green), a test cable with shock-proof plug, a probe with TEST key, alligator clips, a 4 mm adapter, carrying strap, six AA batteries, a fuse, transport case and calibration certificate. The unit is rated IP40 for dry-environment use, works up to 440 V measurement range, and is specified for use up to 2000 m altitude. It meets relevant EN/IEC safety and EMC standards and includes built-in protections such as an internal fuse and polarity/adaptation safeguards.

Applications and workflow

Typical uses include routine electrical installation verification, RCD commissioning and periodic testing, motor and three-phase loop and line impedance checks, insulation and continuity testing, and fault-current estimation for protective-device coordination. The device supports AUTO-start functions, LOCK for continuous insulation testing, null compensation for lead resistance, and selectable RCD test current and waveform (AC or pulsed Type A). Calibration is recommended annually to maintain specified measurement accuracy.

Notes

  • Intended for qualified personnel only; follow all local electrical regulations.
  • Use only included CAT-rated leads and accessories for CAT III measurements.
  • Remove batteries for long-term storage and replace batteries/fuse as indicated by display symbols.
  • High-current ZS/ZI tests can trip upstream RCDs; use NO-TRIP mode when required.
M: OA-GPT-5-NAN

© Copyright 2026 Manual.ly