Manual.ly Logo

Benning CM 9-1 Manual

0.0 · 0 Ratings

PDF manual · 46 Pages

English

M: QW-35-FL
page

/ 46

Loading...
aef559a9656eecfc3bcfb6a4df0785377b25 page 13
10/ 2020
BENNING CM 9-1
19
Operating manual
BENNING CM 9-1
TRUE RMS leakage current clamp according to EN 61557-13 for
- measuring the leakage currents (differential current and protective conductor current) in
electrical systems and devices
- AC/ DC voltage measurements
- AC current measurements
- resistance measurements
- continuity tests
Table of contents
1. User instructions
2. Safety instructions
3. Scope of delivery
4. Device description
5. General information
6. Ambient conditions
7. Electrical specifications
8. Measuring with the BENNING CM 9-1
9. Maintenance
10. Technical data of measuring accessories
11. Environmental note
1. User instructions
This operating manual is intended for
- skilled electricians and
- electrotechnically trained personnel.
The BENNING CM 9-1 is intended for making measurements in dry environment. It must not be
used in power circuits with a nominal voltage higher than CAT IV 300 V or CAT III 600 V (More
details in Section 6. “Ambient conditions”).
The following symbols are used in this operating manual and on the BENNING CM 9-1:
Application around and removal from HAZARDOUS LIVE conductors is permitted.
Warning of electrical danger!
Indicates instructions which must be followed to avoid danger to persons.
Attention! Must comply with documentation!
This symbol indicates that the information provided in the operating manual must be
complied with in order to avoid risks.
CAT III
Measuring category III is applicable to testing and measuring circuits connected to the
distribution circuit of the low-voltage mains installation of a building.
CAT IV
Measuring category IV is applicable to testing and measuring circuits connected to the
feed-in point of the low-voltage mains installation of a building.
Do not use the device in external low-frequency magnetic fields with more than
30 A/m.
This symbol on the BENNING CM 9-1 indicates that the BENNING CM 9-1 is equipped
with protective insulation (protection class II).
Please observe the operating manual!
This symbol appears on the display to indicate a discharged battery.
This symbol designates the „continuity test“ field. The buzzer is intended for acoustic
result output.
(DC) Direct voltage
(AC) Alternating voltage or current
Ground (voltage against ground)

Chat with your Benning CM 9-1 manual using AI

Get instant AI answers from your Benning CM 9-1 manual

Ask anything about the Benning CM 9-1. Answers come from this manual, with the pages they are based on.

CM 9-1 Maintenance Schedule

Remind me when maintenance is due
Yearly
Calibrate the device at factory service

Send the unit to Benning Service Center for recalibration to maintain specified accuracy. Recommended interval is one year.

Show in the manual (page 26)
Regularly
Clean the housing with a dry cloth

Wipe the casing externally with a clean dry cloth. Do not use solvents or scouring agents. Ensure battery compartment is free of electrolyte leaks.

Show in the manual (page 26)

Free maintenance reminders

Timed to your purchase date. Always free, unsubscribe anytime.

By submitting you agree to the privacy policy. Unsubscribe with one click in any email.
M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend CM 9-1?

Yes No

Frequently Asked Questions

A

The device is rated for Overvoltage Category III with a maximum of 600 V and Category IV with a maximum of 300 V. It must not be used in circuits exceeding these limits to ensure user safety.

Is this answer helpful?

A

Press and hold the ZERO/LPF button for two seconds. This activates the filter between 40 Hz and 70 Hz, which helps suppress high-frequency noise from frequency converters.

Is this answer helpful?

A

The BENNING CM 9-1 is powered by two 1.5 V micro batteries, specifically the IEC LR03 or AAA type. Battery replacement is required when the low battery symbol appears on the display.

Is this answer helpful?

A

No, the BENNING CM 9-1 is designed exclusively for dry environments. It has an IP 30 rating, which offers protection against solid objects but no protection against water.

Is this answer helpful?

A

When the input exceeds the selected range, the digital display will show "0L." indicating an overload. Note that there is no specific warning signal for complete overload conditions.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • True RMS measurement capability ensures accurate readings on non-sinusoidal waveforms
  • Complies with CAT III 600 V and CAT IV 300 V safety standards for high-risk environments
  • Integrated low-pass filter effectively suppresses high-frequency interference from inverters
  • Acoustic continuity buzzer activates below 45 ohms for quick circuit verification
  • Large 4-digit LCD display with automatic range selection simplifies reading results
VS

Disadvantages

  • No built-in fuse requires careful handling to prevent internal damage during overloads
  • Battery life may decrease significantly if the backlight or acoustic tests are used frequently
  • Device cannot be opened or repaired by the user, necessitating professional service for issues
  • Limited to dry environments and cannot withstand moisture or water exposure
  • Accuracy can drift outside the specified temperature range of 18 to 28 degrees Celsius
M: QW-35-FL

Product Specification

Measurement Range

max. 60A, max. 600V, 600kΩ

M: QW-35-FL

Product Description

BENNING CM 9-1 Current Clamp Multimeter: Precision and Safety for Electrical Professionals

The BENNING CM 9-1 stands as a robust solution for electricians and technicians requiring precise measurements in complex electrical environments. Designed strictly according to DIN EN 61557-13, this True RMS leakage current clamp multimeter offers a comprehensive suite of diagnostic capabilities essential for maintaining modern electrical systems. Whether you are troubleshooting industrial machinery or inspecting residential wiring, this tool ensures accuracy where it matters most.

At the heart of the BENNING CM 9-1 is its ability to measure leakage currents, including differential and protective conductor currents, with high reliability. The device features a large 4-digit LCD display that clearly presents readings up to 6000 counts, ensuring that even subtle variations in voltage or current are easily visible. Its design prioritizes user safety, adhering to CAT III 600 V and CAT IV 300 V standards, making it suitable for use in distribution circuits and feed-in points without compromising operator protection.

Beyond leakage detection, the multimeter excels in measuring AC and DC voltages, alternating currents, and resistance values. The inclusion of a low-pass filter (LPF) allows users to suppress high-frequency interference signals often generated by frequency converters, providing cleaner data in noisy environments. For continuity testing, an integrated buzzer provides immediate acoustic feedback when resistance drops below 45 ohms, streamlining fault identification. The unit is powered by two standard AAA batteries, offering a battery life of approximately 40 to 60 hours depending on usage patterns.

This versatile instrument comes complete with safety-rated test leads, a protective carrying case, and detailed instructions in multiple languages. Its compact form factor and ergonomic opening lever make it easy to handle around various conductor sizes, with a maximum jaw opening of 23 mm. By combining rigorous safety protocols with advanced measurement technology, the BENNING CM 9-1 remains an indispensable asset for professionals dedicated to electrical integrity and safety.

M: QW-35-FL

© Copyright 2026 Manual.ly