Manual.ly Logo

Axkid Spinkid Manual

0.0 · 0 Ratings

PDF manual · 120 Pages

English

M: OA-GPT-5-NAN
page

/ 120

Loading...
cc67d1794ee67518609924ab7acd8897b42d page 12
18
Care and maintenance
The seat textile cover can be machine washed at 30º C on a gentle cycle. Do not put the cover in a dryer as this can damage the cover
and the padding may separate from the fabric. Visit www.axkid.com to find videos explaining how to remove and attach the cover.
Remove the textile cover:
• Loosen the harness by pressing the harness release button (K) and pull out both shoulder straps (F) at the same time.
• Carefully pull the cover o from the headrest (C).
• Lower the headrest (C) to the lowest position.
• Unlock the harness buckle by pressing the buckle release button (G) and remove the buckle cover.
• Undo the four buttons at the backrest on the inside of the car seat and gently remove the textile cover from the car seat. Be careful around
plastic covers not to damage the textile. Don’t pull to hard.
• Open the shoulder pads (E) and gently remove them from the Velcro.
Install the textile cover
• Reverse the steps from the instruction above to install the textile cover on the car seat again.
• Note that the shoulder pads can be installed at dierent positions. Install them in a position suitable for your child, the shoulder pads should
be positioned on top of the shoulder and on the chest of your child. Also make sure that the rubber side of the shoulder pad is facing your
child’s chest.
I
f the textile seat cover needs replacing, ensure only original products from Axkid are used. If other products are used, the Axkid car seat’s safety
system may be compromised and could lead to severe injury in case of an accident.
Any plastic parts of the Axkid car seat can be cleaned with mild detergent and water. Do not use aggressive chemicals containing solvents or
similar, as this can cause damage to the plastic and compromise the safety of the car seat.
Recycling your car seat
Axkid strongly recommends recycling of old car seats. Before leaving the seat at your local recycling station cut o the harness
straps from the seat, remove the textile cover, remove as many Styrofoam parts as possible, separate metal and plastic parts
if possible. The main part of the seat should be marked unsafe or expired (use a marker) to deter anyone from using it again.
Please check your local municipal guidelines for recycling instructions for the dierent materials.

Chat with your Axkid Spinkid manual using AI

Get instant AI answers from your Axkid Spinkid manual

Ask anything about the Axkid Spinkid. Answers come from this manual, with the pages they are based on.

Spinkid Maintenance Schedule

As needed
Wash textile cover

Machine wash at 30C gentle cycle. Do not use dryer as it may damage fabric and padding.

Show in the manual (page 18)
As needed
Clean plastic parts

Clean with mild detergent and water only. Do not use aggressive chemicals or solvents.

Show in the manual (page 18)
M: QW-35-FL

Ask a Question

0/1000

Do you recommend Spinkid?

Yes No

Frequently Asked Questions

A

Axkid SPINKID is approved for rear-facing use for children with a height between 40–105 cm and up to 18 kg. Use the infant insert for roughly 40–75 cm; remove it as the child grows beyond the insert’s fit.

Is this answer helpful?

A

Install SPINKID using its ISOFIX connectors: fold out the support leg, release and position the anti-rebound/front brace, extend ISOFIX until they click and indicators turn green, push the seat toward the vehicle seat, then lower and lock the support leg until its visual indicator turns green.

Is this answer helpful?

A

Do not install SPINKID on a seat with an active frontal airbag. If you must use that position, the vehicle’s airbag must be disabled following the vehicle manufacturer’s instructions; some vehicles require an authorized service center.

Is this answer helpful?

A

Adjust the headrest to position the harness height so shoulder straps are at or just above your child’s shoulders. Tighten the harness using the harness tension strap until you cannot fit more than one finger between the strap and the child’s shoulder; ensure no twists and that the buckle is fully locked.

Is this answer helpful?

A

Remove the textile cover following the manual and machine wash at 30°C on a gentle cycle; do not tumble dry. Clean plastic parts with mild detergent and water; avoid aggressive chemicals. Use only original Axkid replacement covers to maintain safety.

Is this answer helpful?

A

Replace the Axkid SPINKID after any crash, even minor. Invisible damage can compromise safety. Axkid advises against buying or using secondhand seats due to unknown crash history.

Is this answer helpful?

A

Axkid provides a 24-month warranty from purchase. It does not cover normal wear and tear, damage from incorrect use, negligence, accidents, third-party repairs, or UV-related fading of materials. Keep your purchase receipt for claims.

Is this answer helpful?

M: OA-GPT-5-NAN

Advantages and Disadvantages

Advantages

  • i-Size Enhanced approval (UN R129) for rear-facing safety up to 105 cm/18 kg
  • ISOFIX installation with visual indicators for secure, tool-free attachment
  • Adjustable headrest, removable infant insert, and four recline positions for growth and comfort
  • Support leg with visual green indicator to confirm correct floor contact
  • Removable machine-washable cover and straightforward cleaning instructions
VS

Disadvantages

  • Cannot be used forward-facing; rear-facing only may require more vehicle space
  • Must not be installed where an active frontal airbag is present unless disabled
  • Textile cover must be Axkid original to maintain safety—limits third-party replacements
  • Seat must be replaced after any accident; no recommended secondhand use
  • Installation requires correct vehicle ISOFIX/i-Size compatibility and following manual closely
M: OA-GPT-5-NAN

Product Specification

Group

i-Size

Weight class

0-39.68 lb

Age group

0-4Y

Harness type

Five-point safety harness

Installation

Rearward facing

Features

height-adjustable headrest and shoulder straps, side impact protection, adjustable seating position, recline position, swivel function, newborn insert, magnetic harness holder

Dimensions (WxHxD)

17.32x24.80x24.80in

Weight

32.06 lb

M: OA-GPT-54-NAN

Product Description

Axkid SPINKID — Axkid Spinkid Manual

Axkid SPINKID is a rear-facing, i-Size Enhanced child restraint designed for children 40–105 cm (up to 18 kg). Approved under UN Regulation No. 129, SPINKID installs using ISOFIX and is intended for i-Size compatible seating positions. The seat includes features to grow with the child: an adjustable headrest, removable infant insert (for ~40–75 cm), multiple recline positions, and a support leg with a visual indicator to confirm correct floor contact.

Key product features

SPINKID emphasizes safety and usability. It installs with ISOFIX connectors that click and display green when engaged. A front brace (anti-rebound bar) and adjustable support leg stabilize the seat. The harness is adjusted by moving the headrest; shoulder straps must sit at or just above the child’s shoulders and tightened so only one finger fits between strap and shoulder. The seat rotates to an outer locked position to ease placing the child in the seat. Four fixed recline positions allow comfort adjustments even when the child is strapped in.

The seat shell and textiles are serviceable: the textile cover is removable and machine washable at 30°C on a gentle cycle (do not tumble dry). Plastic parts clean with mild detergent and water; aggressive chemicals are prohibited. Replacement textiles and parts must be genuine Axkid products to preserve safety performance. After any collision the seat should be replaced; Axkid discourages buying secondhand seats.

Installation and positioning

SPINKID must be used rear-facing and is approved for i-Size seating positions. Never install on a seat with an active frontal airbag unless the airbag is disabled per vehicle manufacturer instructions. Installation steps include folding out the support leg, releasing and positioning the anti-rebound bar, extending and clicking the ISOFIX connectors, then lowering and locking the support leg (visual indicator turns green). To remove, collapse the support leg, fold the front brace, and retract ISOFIX connectors.

Maintenance and end-of-life

The cover can be washed at 30°C; do not tumble dry. Follow the manual’s removal and reinstallation steps to avoid damaging plastic components or harness parts. Axkid recommends recycling old seats: cut harness straps, remove cover and foam, separate metals/plastics when possible, and mark the shell as unsafe to prevent reuse.

Notes

  • Always follow manufacturer and vehicle manuals for seat placement and airbag guidance.
  • Replace the seat after any crash, even minor.
  • Use only original Axkid replacement parts and textiles.
  • Never leave a child unattended in the vehicle.
M: OA-GPT-5-NAN

© Copyright 2026 Manual.ly