Manual.ly Logo

Atika KSH 710 SDS Manual

0.0 · 0 Ratings

PDF manual · 176 Pages

English

M: QW-35-FL
page

/ 176

Loading...
4e358b1ba1162dbc7c70ea5df9874aadc702 page 9
9
Prüfen der Kettenschmierung
Benutzen Sie nie den Hochentaster ohne funktionie-
rende Kettenschmierung.
Sie überprüfen die Funktion der automatischen Kettenschmie-
rung, indem Sie den Hochentaster einschalten und ihn mit der
Spitze in Richtung eines Kartons oder Papiers auf dem Boden
halten.
Berühren Sie den Boden nicht mit der Kette. Sicherheitsab-
stand von 20 cm einhalten.
Zeigt sich beim Überprüfen eine zunehmende Ölspur, arbeitet
die Öl-Automatik einwandfrei.
Zeigt sich trotz vollem Öltank keine Ölspur
reinigen Sie den Ölflusskanal (26) und
reinigen Sie die Kettenspannbohrung (27)
Sollte dies zu keinem Erfolg führen, wenden Sie sich bitte an
den Kundendienst.
Inbetriebnahme
Vor jedem Einstellen oder Überprüfen des Gerätes Netzste-
cker ziehen.
Tragen Sie Schutzhandschuhe, um Verletzungen zu ver-
meiden.
Sägekette spannen
Überprüfen Sie die Sägekettenspannung
vor Arbeitsbeginn
nach den ersten Schnitten
während des Sägens regelmäßig alle 10 Minuten
Nur mit einer richtig gespannten Sägekette und einer aus-
reichenden Schmierung haben Sie Einfluss auf die Lebensdau-
er.
Bitte beachten Sie folgendes:
eine neue Sägekette muss öfters nachgespannt werden
bei Erwärmung der Kette auf Betriebstemperatur dehnt sie
sich aus und muss nachgespannt werden.
Nach Beendigung der Sägearbeiten die Sägekette wie-
der entspannen, denn bei Abkühlung würden sonst zu hohe
Spannungen in der Sägekette entstehen.
flattert die Kette oder tritt sie aus der Führung heraus, sofort
nachspannen.
Spannen der Sägekette:
Legen Sie den Hochentaster wie abgebildet auf eine
gerade Fläche.
Lösen Sie die Befestigungsschraube (3) um max. 1
Umdrehung.
Drehen Sie den Kettenspannring (4) schrittweise im
Uhrzeigersinn bis die richtige Kettenspannung erreicht
ist.
Die Befestigungsschraube (3) dreht sich mit, even-
tuell muss sie während des Spannvorganges wieder ge-
löst werden.
Die Sägekette ist richtig gespannt, wenn sie in der Mitte
des Schwertes um ca. 3 – 4 mm angehoben werden
kann.
Drehen Sie den Kettenspannring (4) gegen den Uhrzei-
gersinn, wenn die Sägekette zu stark gespannt ist.
Prüfen Sie, ob die Kettenglieder richtig im Führungs-
schlitz der Führungsschiene liegen.
Ziehen Sie die Befestigungsschraube mit der Hand wie-
der fest.
Anlegen des Schultergurtes
Legen Sie den Gurt (17) über die Schulter und stellen sie
die Gurtlänge so ein, dass sich die Gurtbefestigung (b)
auf Höhe Ihrer Hüfte befindet. Der Schnellverschluss
(18) befindet sich auf der Vorderseite.
Der Schnellverschluss kann dann mit der linken Hand
geöffnet werden.
Einstellen der Arbeitshöhe
Lösen Sie die Feststellschraube (10) Dann können Sie
die beiden Teleskopstiele (7, 11) auseinander- oder zu-
sammenschieben.
Einstellen des Arbeitswinkels
/ Drücken Sie die Winkelverstellung (6) und schwen-
ken Sie den Gerätekopf in die gewünschte Position
Netzanschluss
Vergleichen Sie die auf dem Gerätetypenschild angegebene
Spannung mit der Netzspannung und schließen Sie das Ge-
rät an die entsprechende und vorschriftsmäßige Steckdose
an.
geerdete Schuko-Steckdose, Netzspannung 230 V mit
Fehlerstromschutzschalter (FI-Schalter 30 mA).
Verwenden Sie Verlängerungskabel mit ausreichendem
Querschnitt.
Netzabsicherung
10 A träge
Anbringen des Verlängerungskabels
Stecken Sie die Kupplung des Verlängerungskabels auf
den Stecker des Gerätes.
Ziehen Sie das Verlängerungskabel als Schlaufe durch
die Kabelzugentlastung (14) und hängen Sie es ein.
Achten Sie darauf, dass das Verlängerungskabel genü-
gend Spiel hat und nach hinten von dem Hochentaster
wegführt, außerhalb des Bereichs Sägekette und Säge-
gut.
Ein-/Ausschalten
Benutzen Sie kein Gerät, bei dem sich der Schalter nicht
ein- und ausschalten lässt. Beschädigte Schalter müssen
unverzüglich vom Kundendienst repariert oder ersetzt
werden.
Beim Einschalten ist der Hochentaster sicher abzustützen und
mit beiden Händen festzuhalten. Kette und Führungsschiene
müssen frei stehen.

Chat with your Atika KSH 710 SDS manual using AI

Get instant AI answers from your Atika KSH 710 SDS manual

Ask anything about the Atika KSH 710 SDS. Answers come from this manual, with the pages they are based on.

KSH 710 SDS Maintenance Schedule

Every 10 minutes
Check and adjust saw chain tension

Check tension before work, after first cuts, and regularly every 10 minutes during sawing. Adjust if the chain flutters or comes out of the guide.

After each use
Clean the power pruner housing

Clean the case with a soft brush or dry cloth. Ensure ventilation slots are free. Do not use water, solvents, or polishing agents.

Show in the manual (page 12)
Regularly
Inspect and clean guide bar slot

Regularly inspect and clean the guide slot, clamping plate, and chain clamping boring. Remove burrs with a flat file.

Show in the manual (page 11)
After each chain change/sharpening
Turn the guide bar

Rotate the guide bar to avoid one-sided wear.

Show in the manual (page 11)
Regularly
Check chain wheel for wear

Check teeth of the chain wheel for wear or damage. Replace immediately via customer service if worn.

Show in the manual (page 12)
Before each start-up
Check oil level

Check the oil tank level. Refill immediately if it indicates MIN to prevent the chain from running dry.

Show in the manual (page 22)
Regularly
Check connection cables

Regularly check connection cables for damage and replace them if they are defective.

M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend KSH 710 SDS?

Yes No

Frequently Asked Questions

A

The maximum cutting length is 180 mm. You should not attempt to cut branches with a diameter larger than this limit to avoid damaging the machine or causing injury.

Is this answer helpful?

A

No, you must never operate the high reach trowel while standing on a ladder, scaffolding, or tree. Always stand on firm, level ground to maintain balance and control.

Is this answer helpful?

A

Turn on the machine and hold the guide bar tip near a piece of cardboard or paper at a safe distance. If an increasing oil track appears on the surface, the lubrication system is functioning correctly.

Is this answer helpful?

A

You must use bio-degradable chainsaw oil. Using recycled oil or non-approved oils will void the warranty and can damage the chain and guide bar.

Is this answer helpful?

A

Check the chain tension before starting work, after the first few cuts, and then regularly every 10 minutes during operation to ensure safe and efficient cutting.

Is this answer helpful?

A

No, this tool is designed exclusively for cutting wood. Using it on plastics, masonry, or other building materials is dangerous and can lead to severe accidents.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Powerful 710 W motor ensures fast and efficient cutting of thick branches
  • Telescopic pole allows adjustable working height for hard-to-reach limbs
  • Automatic chain lubrication system protects the saw chain and guide bar
  • Comprehensive safety features include insulated handles and clear warnings
  • Compact design makes transport and storage easy for home gardeners
VS

Disadvantages

  • Requires regular sharpening and tensioning of the saw chain for best results
  • Cannot be used on unstable surfaces like ladders or trees due to safety risks
  • Not suitable for professional forestry work or cutting down entire trees
  • Must purchase specific biodegradable oil separately as it is not pre-filled
  • Heavy vibration levels require anti-vibration accessories for extended use
M: QW-35-FL

Product Specification

Type

Pole Saw

Power

710W

Bar Length

7.1 in

Chain Speed

42.65 ft/s

Chain Pitch

3/8"

Oil Tank Capacity

5.07 fl oz

Features

Extra handle, telescopic (8.1-10.08 ft), automatic chain lubrication

Vibration Level

11.81 ft/s²

Noise Emission

103dB(A)

Weight

10.14 lbs

Package Contents

Saw chain (Oregon), carrying strap

M: QW-35-FL

Product Description

Atika KSH 710 SDS Electric High Reach Trowel Manual Overview

The Atika KSH 710 SDS is a specialized electric high reach trowel designed for efficient pruning of tall branches on standing trees. This powerful tool features a robust 710-watt motor that delivers a saw chain speed of 13 meters per second, ensuring clean cuts even through thicker wood. The telescopic pole allows users to adjust the working height effortlessly, making it ideal for private gardens and allotments where reaching high limbs is necessary without ladders.

Safety is paramount with this device. The manual emphasizes strict adherence to safety protocols, including wearing protective gear such as helmets, eye protection, and hearing guards. Users must maintain a safe distance of at least six meters from bystanders and ten meters from overhead power lines. The tool includes a built-in oil tank for automatic chain lubrication, which extends the life of the saw chain and guide bar while maintaining optimal cutting performance.

Assembly is straightforward, involving the connection of the upper and lower telescope rods and the attachment of the front handle. Before operation, users must ensure the saw chain is correctly tensioned and sharp. The manual provides detailed instructions on avoiding kickback by using the lower edge of the guide bar and never cutting with the tip. Regular maintenance, including cleaning the air vents and sharpening the chain, is essential for longevity and safe operation.

Important Notes

  • Always use biodegradable chainsaw oil specifically designed for this equipment.
  • Do not operate the machine in wet conditions or near flammable liquids.
  • Ensure the extension cable has a sufficient cross-section to prevent voltage drop.
  • Never work on unstable surfaces like ladders or trees.
  • Store the device in a dry place with the chain guard attached.
M: QW-35-FL

© Copyright 2026 Manual.ly