Manual.ly Logo

Atika KSH 710 SDS Manual

0.0 · 0 Ratings

PDF manual · 176 Pages

English

M: QW-35-FL
page

/ 176

Loading...
4e358b1ba1162dbc7c70ea5df9874aadc702 page c
12
Kettenrad
Die Beanspruchung des Kettenrades (24) ist besonders groß.
Überprüfen Sie die Zähne des Kettenrades regelmäßig auf
Abnutzung oder Beschädigung.
Ein abgenutztes oder beschädigtes Kettenrad vermin-
dert die Lebensdauer der Sägekette und sollte deswegen un-
verzüglich vom Kundendienst ausgetauscht werden.
Reinigung
Reinigen Sie den Hochentaster sorgfältig nach jedem Ge-
brauch, damit die einwandfreie Funktion erhalten bleibt.
Reinigen Sie das Gehäuse mit einer weichen Bürste oder
einem trockenen Lappen.
Wasser, Lösungsmittel und Poliermittel dürfen nicht
verwendet werden.
Achten Sie darauf, dass die Lüftungsschlitze für die Motor-
kühlung frei sind (Gefahr der Überhitzung).
Demontieren Sie nach längerer Einsatzdauer (1 – 3
Stunden) die Abdeckung (5), die Führungsschiene (1) und
die Kette (2) und reinigen Sie sie mit einer Bürste.
Säubern Sie die Sägekette bei starker Verschmutzung mit
einem handelsüblichen Kettenreiniger.
Befreien Sie das Kettenrad (24) und die Führungs-
schienenaufnahmen (a) mit einer Bürste von allen Anhaf-
tungen.
Säubern Sie den Ölflusskanal (26) mit einem saube-
ren Lappen oder einem Pinsel.
Tansport
Vor jedem Transport Netzstecker ziehen.
Transportieren Sie den Hochentaster nur mit aufgesteck-
tem Kettenschutz.
Lagerung
Bewahren Sie unbenutzte Geräte an einem trockenen, ver-
schlossenen Ort außerhalb der Reichweite von Kindern auf.
Beachten Sie vor einer längeren Lagerung folgendes, um die
Lebensdauer des Hochentasters zu verlängern und ein
leichtgängiges Bedienen zu gewährleisten:
Führen Sie eine gründliche Reinigung durch.
Entfernen Sie das Öl aus dem Öltank.
Tipp:
Einige Kettenöle neigen nach längerer Zeit zur Verkrustung.
Deswegen sollte das Ölsystem vor einer längeren Lagerung
mit einem handelsüblichen Kettensägenreiniger durchgespült
werden. Füllen Sie den Reiniger bis zur Hälfte (ca. 50 ml) in
den Öltank. Verschließen Sie den Tank. Schalten Sie den
Hochentaster ohne montierte Führungsschiene und Kette so-
lange ein, bis der ganze Reiniger aus der Ölöffnung des
Hochentasters ausgetreten ist.
Legen Sie die Sägekette nach dem Reinigen kurz in ein
Ölbad und wickeln sie anschließend in ein Ölpapier.
Stecken Sie den Kettenschutz auf.
Gerätebeschreibung / Ersatzteile
Pos. Bestell-Nr. Bezeichnung
Pos. Bestell-Nr. Bezeichnung
1 364447 Führungsschiene (Schwert)
16 hinterer Handgriff
2 364406 Sägekette (90JG033X)
17 364409 Tragegurt
2 364437 Sägekette (90PX033X)
18 Schnellverschluss
3 Befestigungsschraube
19 364410 vorderer Handgriff
4 Kettenspannring
20 364413 Öltankverschluss
5 364475 Abdeckung
21 364417 Buchse
6 Winkelverstellung
22 364415 Sechskantschraube M 6 x 65
7 Oberer Teleskopstiel
23 364416 Flügelmutter
8 364444 Aufnahme
24 364414 Kettenrad
9 364408 Feststellschraube (Aufnahme)
25 364476 Spannplatte
10 Feststellschraube
26 Ölflusskanal
11 Unterer Teleskopstiel
27 Kettenspannbohrung
12 Einschaltsperre
28 364412 Kettenschutz
13 Ein-/Ausschalter
29 364404 Sicherheitsaufkleber
14 Kabelzugentlastung
30 364448 Kohlebürstenpaar (ohne Abb.)
15 Geräteleitung mit Stecker
31 400144 Sägekettenöl 1 l (ohne Abb.)

Chat with your Atika KSH 710 SDS manual using AI

Get instant AI answers from your Atika KSH 710 SDS manual

Ask anything about the Atika KSH 710 SDS. Answers come from this manual, with the pages they are based on.

KSH 710 SDS Maintenance Schedule

Every 10 minutes
Check and adjust saw chain tension

Check tension before work, after first cuts, and regularly every 10 minutes during sawing. Adjust if the chain flutters or comes out of the guide.

After each use
Clean the power pruner housing

Clean the case with a soft brush or dry cloth. Ensure ventilation slots are free. Do not use water, solvents, or polishing agents.

Show in the manual (page 12)
Regularly
Inspect and clean guide bar slot

Regularly inspect and clean the guide slot, clamping plate, and chain clamping boring. Remove burrs with a flat file.

Show in the manual (page 11)
After each chain change/sharpening
Turn the guide bar

Rotate the guide bar to avoid one-sided wear.

Show in the manual (page 11)
Regularly
Check chain wheel for wear

Check teeth of the chain wheel for wear or damage. Replace immediately via customer service if worn.

Show in the manual (page 12)
Before each start-up
Check oil level

Check the oil tank level. Refill immediately if it indicates MIN to prevent the chain from running dry.

Show in the manual (page 22)
Regularly
Check connection cables

Regularly check connection cables for damage and replace them if they are defective.

M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend KSH 710 SDS?

Yes No

Frequently Asked Questions

A

The maximum cutting length is 180 mm. You should not attempt to cut branches with a diameter larger than this limit to avoid damaging the machine or causing injury.

Is this answer helpful?

A

No, you must never operate the high reach trowel while standing on a ladder, scaffolding, or tree. Always stand on firm, level ground to maintain balance and control.

Is this answer helpful?

A

Turn on the machine and hold the guide bar tip near a piece of cardboard or paper at a safe distance. If an increasing oil track appears on the surface, the lubrication system is functioning correctly.

Is this answer helpful?

A

You must use bio-degradable chainsaw oil. Using recycled oil or non-approved oils will void the warranty and can damage the chain and guide bar.

Is this answer helpful?

A

Check the chain tension before starting work, after the first few cuts, and then regularly every 10 minutes during operation to ensure safe and efficient cutting.

Is this answer helpful?

A

No, this tool is designed exclusively for cutting wood. Using it on plastics, masonry, or other building materials is dangerous and can lead to severe accidents.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Powerful 710 W motor ensures fast and efficient cutting of thick branches
  • Telescopic pole allows adjustable working height for hard-to-reach limbs
  • Automatic chain lubrication system protects the saw chain and guide bar
  • Comprehensive safety features include insulated handles and clear warnings
  • Compact design makes transport and storage easy for home gardeners
VS

Disadvantages

  • Requires regular sharpening and tensioning of the saw chain for best results
  • Cannot be used on unstable surfaces like ladders or trees due to safety risks
  • Not suitable for professional forestry work or cutting down entire trees
  • Must purchase specific biodegradable oil separately as it is not pre-filled
  • Heavy vibration levels require anti-vibration accessories for extended use
M: QW-35-FL

Product Specification

Type

Pole Saw

Power

710W

Bar Length

7.1 in

Chain Speed

42.65 ft/s

Chain Pitch

3/8"

Oil Tank Capacity

5.07 fl oz

Features

Extra handle, telescopic (8.1-10.08 ft), automatic chain lubrication

Vibration Level

11.81 ft/s²

Noise Emission

103dB(A)

Weight

10.14 lbs

Package Contents

Saw chain (Oregon), carrying strap

M: QW-35-FL

Product Description

Atika KSH 710 SDS Electric High Reach Trowel Manual Overview

The Atika KSH 710 SDS is a specialized electric high reach trowel designed for efficient pruning of tall branches on standing trees. This powerful tool features a robust 710-watt motor that delivers a saw chain speed of 13 meters per second, ensuring clean cuts even through thicker wood. The telescopic pole allows users to adjust the working height effortlessly, making it ideal for private gardens and allotments where reaching high limbs is necessary without ladders.

Safety is paramount with this device. The manual emphasizes strict adherence to safety protocols, including wearing protective gear such as helmets, eye protection, and hearing guards. Users must maintain a safe distance of at least six meters from bystanders and ten meters from overhead power lines. The tool includes a built-in oil tank for automatic chain lubrication, which extends the life of the saw chain and guide bar while maintaining optimal cutting performance.

Assembly is straightforward, involving the connection of the upper and lower telescope rods and the attachment of the front handle. Before operation, users must ensure the saw chain is correctly tensioned and sharp. The manual provides detailed instructions on avoiding kickback by using the lower edge of the guide bar and never cutting with the tip. Regular maintenance, including cleaning the air vents and sharpening the chain, is essential for longevity and safe operation.

Important Notes

  • Always use biodegradable chainsaw oil specifically designed for this equipment.
  • Do not operate the machine in wet conditions or near flammable liquids.
  • Ensure the extension cable has a sufficient cross-section to prevent voltage drop.
  • Never work on unstable surfaces like ladders or trees.
  • Store the device in a dry place with the chain guard attached.
M: QW-35-FL

© Copyright 2026 Manual.ly