Manual.ly Logo

Atika KSH 710 SDS Manual

0.0 · 0 Ratings

PDF manual · 176 Pages

English

M: QW-35-FL
page

/ 176

Loading...
4e358b1ba1162dbc7c70ea5df9874aadc702 page 16
22
Is the power pruner in good and safe condition?
Is the oil tank filled?
Check the oil level on a regular basis. Replenish
immediately oil when oil level indicates
„MIN“ so that the saw
chain does not run dry.
Is saw chain clamped correctly?
Observe the points in paragraph
„Clamping saw chain“.
Is saw chain sharpened correctly?
Use only well sharpened saw chains as edgeless saw
chains increase not only the risk of backstrokes but also
charge the motor.
Is handhold clean and dry
– free of oil and resin?
Is workplace free of risks to stumble?
Do you wear the required protective equipment?
Did you read and understand all advices?
Is the power plug and the extension cable in good
condition?
Do not use any defective cables.
Is the extension cable correctly placed?
Work instructions (saw techniques)
Do not cut thin branches or bosks. The power pruner is not
suitable for those works.
Cut larger branches into several sections to avoid splintering
and breaking.
Do not cut any branches where their diameter is greater
than the cutting length of the device.
Do not stand directly underneath a branch to be cut.
Watch out especially for falling branches.
Also look out for branches snapping back.
Always wear a helmet in order to protect yourself against
perches falling down.
Step cut
For horizontal branches without being top heavy
The branch section falls down in a controlled manner
without tipping over.
Set the first cut from below, approx. one third of the
branch diameter.
The second cut is made on the same level as the first cut
or moved further toward the inside (negative breaking
step).
Remove the remaining branch section.
Attention: Step cut error!
If the cut is made offset toward the outside (positive breaking
step) and exceeded, the power pruner can be pulled along.
Maintenance and cleaning
Before each maintenance and cleaning work
− switch off device
− Wait for standstill of the power pruner
− Pull out power plug
Maintenance and repair work other than those described in this
chapter is only allowed to be carried out by service staff.
For maintaining and cleaning, removed security devices must
unconditionally be mounted properly and proved again.
Use only original parts. Other parts can result in unexpected
damages and injuries.
Maintenance
In order to avoid possible injuries wear gloves.
To guarantee a long and reliable usage of the power pruner
carry out the following maintenance works regularly.
Check the power pruner for
−
loose or damaged saw chain
− loose fastenings
− wear, especially chain, guide bar and chain wheel
− worn or damaged components
− correct assembly and faultless covers and protective
devices.
Necessary repair works or maintenance have to be carried out
before using the power pruner.
Saw chain and guide bar
Saw chain and guide bar are exposed to a great extent of
wearing. Replace the saw chain and the guide bar without any
delay if their proper function is no longer ensured.
“Installing
the guide bar and the saw chain
”.
Sharpening of saw chain
You can only work safely and well with a sharp
and clean saw chain. Damaged or incorrectly
sharpened saw chains increase the risk of
kickbacks.
The saw chain has to be sharpened if
instead of wood shavings only saw dust is ejected
you have to press the power pruner through the wood during
cutting
For sharpening a saw chain some expertise is necessary. The
saw chain must be regrinded in a specialised shop.
You can also sharpen your saw chain yourself by using our
electric sharpener KSG 220 A (article-no.: 302360).
Cleaning of guide bar
Regularly inspect and clean
the guide slot (c) of the guide bar and
the clamping plate (25) and the chain clamping
boring (27)
Remove any burr using a flat file and emery paper.
Turn round the guide bar after each chain
exchange/sharpening to avoid single-side wearing.
Immediately replace a damaged guide bar.

Chat with your Atika KSH 710 SDS manual using AI

Get instant AI answers from your Atika KSH 710 SDS manual

Ask anything about the Atika KSH 710 SDS. Answers come from this manual, with the pages they are based on.

KSH 710 SDS Maintenance Schedule

Every 10 minutes
Check and adjust saw chain tension

Check tension before work, after first cuts, and regularly every 10 minutes during sawing. Adjust if the chain flutters or comes out of the guide.

After each use
Clean the power pruner housing

Clean the case with a soft brush or dry cloth. Ensure ventilation slots are free. Do not use water, solvents, or polishing agents.

Show in the manual (page 12)
Regularly
Inspect and clean guide bar slot

Regularly inspect and clean the guide slot, clamping plate, and chain clamping boring. Remove burrs with a flat file.

Show in the manual (page 11)
After each chain change/sharpening
Turn the guide bar

Rotate the guide bar to avoid one-sided wear.

Show in the manual (page 11)
Regularly
Check chain wheel for wear

Check teeth of the chain wheel for wear or damage. Replace immediately via customer service if worn.

Show in the manual (page 12)
Before each start-up
Check oil level

Check the oil tank level. Refill immediately if it indicates MIN to prevent the chain from running dry.

Show in the manual (page 22)
Regularly
Check connection cables

Regularly check connection cables for damage and replace them if they are defective.

M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend KSH 710 SDS?

Yes No

Frequently Asked Questions

A

The maximum cutting length is 180 mm. You should not attempt to cut branches with a diameter larger than this limit to avoid damaging the machine or causing injury.

Is this answer helpful?

A

No, you must never operate the high reach trowel while standing on a ladder, scaffolding, or tree. Always stand on firm, level ground to maintain balance and control.

Is this answer helpful?

A

Turn on the machine and hold the guide bar tip near a piece of cardboard or paper at a safe distance. If an increasing oil track appears on the surface, the lubrication system is functioning correctly.

Is this answer helpful?

A

You must use bio-degradable chainsaw oil. Using recycled oil or non-approved oils will void the warranty and can damage the chain and guide bar.

Is this answer helpful?

A

Check the chain tension before starting work, after the first few cuts, and then regularly every 10 minutes during operation to ensure safe and efficient cutting.

Is this answer helpful?

A

No, this tool is designed exclusively for cutting wood. Using it on plastics, masonry, or other building materials is dangerous and can lead to severe accidents.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Powerful 710 W motor ensures fast and efficient cutting of thick branches
  • Telescopic pole allows adjustable working height for hard-to-reach limbs
  • Automatic chain lubrication system protects the saw chain and guide bar
  • Comprehensive safety features include insulated handles and clear warnings
  • Compact design makes transport and storage easy for home gardeners
VS

Disadvantages

  • Requires regular sharpening and tensioning of the saw chain for best results
  • Cannot be used on unstable surfaces like ladders or trees due to safety risks
  • Not suitable for professional forestry work or cutting down entire trees
  • Must purchase specific biodegradable oil separately as it is not pre-filled
  • Heavy vibration levels require anti-vibration accessories for extended use
M: QW-35-FL

Product Specification

Type

Pole Saw

Power

710W

Bar Length

7.1 in

Chain Speed

42.65 ft/s

Chain Pitch

3/8"

Oil Tank Capacity

5.07 fl oz

Features

Extra handle, telescopic (8.1-10.08 ft), automatic chain lubrication

Vibration Level

11.81 ft/s²

Noise Emission

103dB(A)

Weight

10.14 lbs

Package Contents

Saw chain (Oregon), carrying strap

M: QW-35-FL

Product Description

Atika KSH 710 SDS Electric High Reach Trowel Manual Overview

The Atika KSH 710 SDS is a specialized electric high reach trowel designed for efficient pruning of tall branches on standing trees. This powerful tool features a robust 710-watt motor that delivers a saw chain speed of 13 meters per second, ensuring clean cuts even through thicker wood. The telescopic pole allows users to adjust the working height effortlessly, making it ideal for private gardens and allotments where reaching high limbs is necessary without ladders.

Safety is paramount with this device. The manual emphasizes strict adherence to safety protocols, including wearing protective gear such as helmets, eye protection, and hearing guards. Users must maintain a safe distance of at least six meters from bystanders and ten meters from overhead power lines. The tool includes a built-in oil tank for automatic chain lubrication, which extends the life of the saw chain and guide bar while maintaining optimal cutting performance.

Assembly is straightforward, involving the connection of the upper and lower telescope rods and the attachment of the front handle. Before operation, users must ensure the saw chain is correctly tensioned and sharp. The manual provides detailed instructions on avoiding kickback by using the lower edge of the guide bar and never cutting with the tip. Regular maintenance, including cleaning the air vents and sharpening the chain, is essential for longevity and safe operation.

Important Notes

  • Always use biodegradable chainsaw oil specifically designed for this equipment.
  • Do not operate the machine in wet conditions or near flammable liquids.
  • Ensure the extension cable has a sufficient cross-section to prevent voltage drop.
  • Never work on unstable surfaces like ladders or trees.
  • Store the device in a dry place with the chain guard attached.
M: QW-35-FL

© Copyright 2026 Manual.ly