Manual.ly Logo

Atika KS 2002/40 Manual

1.0 · 1 Ratings

PDF manual · 167 Pages

English

M: QW-35-FL
page

/ 167

Loading...
eb6ffe989cfeae2f852cf6aee59cfdb9363c page 1c
27
Safeguard the dangerous zone (D) before cutting.
Make sure that there are no persons or animals in the
fall area. Danger to life!
Make sure that the working area around the trunk is
free of risk to stumble and that you have an escape route (F)
which is free of obstacles.
Before cutting the tree down decide on the felling
direction (C). Before chopping the tree decide on the
chopping direction.
Consider in this case the balance point
of the treetop, neighbour trees, slope direction, state of
health of the tree and the wind direction.
On this side the
kerf is cut in.
Remove interfering branches, scrub and obstacles from the
working area at the trunk and make sure that you have a
safe standing position.
Thoroughly clean the trunk foot – sand, stones and other
foreign objects make the saw chain edgeless or may
damage it.
Consider the state of health of the tree – be careful with
trunks with damages or deadwood (droughty, rotten or dead
wood).
Chopping a tree:
Cut a kerf with the saw of approximately one third of the tree
diameter into the trunk. First of all place the horizontal cut
and then as secondly a cut from top in an angle of 45°.
Shout the warning "Caution" or "Tree is falling" before
starting the fell cut.
Now saw on the opposite side of the trunk a horizontal
chopping cut.
This cut should be placed a bit higher (appr. 4
cm) than the horizontal cut of the kerf.
By no means cut through the trunk.
Appr. 1/10 of the trunk
diameter must remain.
If the tree starts falling ahead of time
pull out the chain saw immediately out of the cut and step
back or to the side.
Push a key into the horizontal chopping cut in order to make
the tree falling.
Pay attention, when tree starts falling, to perches or twigs
falling down.
Maintenance and cleaning
Before each maintenance and cleaning work
switch off device
wait for stop of chain saw
pull out main plug
Further maintenance and cleaning works than described in this
chapter shall only be carried out by the manufacturer or
companies named by the manufacturer.
For maintaining and cleaning, removed security devices must
unconditionally be mounted properly and proved again.
Use only original parts. Other parts can result in unexpected
damages and injuries.
Maintenance
In order to avoid possible injuries wear gloves.
To guarantee a long and reliable usage of the chain saws carry
out the following maintenance works regularly.
Check the chain saw for obvious defects such as
loose, hung out or damaged saw chain
loose fastenings
worn or damaged components
Check the chain saw after each application for
wear, especially chain, guide bar and chain wheel.
correctly assembled and faultless covers and protective
devices.
Necessary repair works or maintenance works have to be
carried out before the usage of the chain saw.
Sharpening of saw chain
You can only work safely and well with a sharp
and clean saw chain. Damaged or incorrectly
sharpened saw chains increase the risk of
kickbacks.
The saw chain has to be sharpened if
only wood dust is thrown out instead of shavings
you have to press the chain saw through the wood during
cutting
Inexperienced users: Have the saw chain sharpened by a
specialist/service workshop.
You can also sharpen your saw chain yourself by using our
electric sharpener KSG 220 (article-no.: 302360).
Saw chain type Oregon 91 PJ 057X
Depth gauge distance T 0,64 mm (.025“)
Sharpening angle α 30°
Breast angle β 85°
Planing tooth length a min. 3 mm
Exchanging saw chain and guide bar
Saw chain and guide bar are exposed to great wearing
demands. Immediately exchange saw chain and guide bar
when the faultless function is not guaranteed.
Put the chain saw on an even face.
Remove the cover (10) by loosening the fastening
screw (11).
Turn the chain clamper (21) anti-clockwise in order to
release the saw chain a bit.
Take off the guide bar with saw chain.
Clean the guide slot thoroughly when only the saw chain is
exchanged.
When assembling, pay attention that the chain links
are lying correctly within the guide slot and on the chain
wheel (13).
Turn the chain clamp (21) clockwise until the saw chain is
clamped.
Now, refasten the cover (10).
Clamp the saw chain as described in paragraph „Clamping
of saw chain“.

Chat with your Atika KS 2002/40 manual using AI

Get instant AI answers from your Atika KS 2002/40 manual

Ask anything about the Atika KS 2002/40. Answers come from this manual, with the pages they are based on.

KS 2002/40 Maintenance Schedule

Before each use
Check chain brake function

Start engine, hold saw with both hands, press front hand guard. Chain must stop immediately. Do not use if brake fails.

Show in the manual (page 26)
During use (every 10 mins)
Check and adjust saw chain tension

Check tension after first cuts and regularly every 10 minutes during sawing. Adjust until chain lifts 3-4mm in center of guide bar.

Show in the manual (page 26)
After each use
Clean the chain saw

Clean case with soft brush or dry cloth. Ensure ventilation slots are free. Clean oil flow channel and remove debris from chain wheel.

Show in the manual (page 29)
After each use
Inspect for wear and damage

Check chain, guide bar, and chain wheel for wear. Verify all covers and safety devices are correctly assembled and intact.

Show in the manual (page 28)
Regularly
Check chain wheel teeth

Inspect chain wheel teeth for wear or damage. Replace immediately via customer service if worn to avoid reducing chain life.

Show in the manual (page 29)
As needed
Sharpen the saw chain

Sharpen when only dust is produced or pressing is required. Use correct angles: 30 deg sharpening, 85 deg breast angle. Depth gauge 0.64 mm.

Show in the manual (page 28)
Before long-term storage
Flush oil system and clean saw

Thoroughly clean saw. Drain oil tank and flush system with chain cleaner to prevent encrustation. Store chain in oil bath and wrapped in oil paper.

Show in the manual (page 29)
M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend KS 2002/40?

Yes No
0
User Pic

tross68

5 months ago

How long does this chainsaw typically last before breaking down?

0
User Pic

Manual.ly

5 months ago

Based on user feedback, some units have experienced failures after approximately 22 months of light use. While the purchase price is low, we recommend registering your product for warranty support if you encounter defects within the coverage period.

M: QW-35-FL
M: QW-35-FL
0
User Pic

Roderick Schaden

4 months ago

Is it worth buying this saw given reports of early failure?

M: QW-35-FL

Frequently Asked Questions

A

You should only fell trees where the trunk diameter is smaller than the 400 mm guide bar length to ensure safety and proper control.

Is this answer helpful?

A

No, the Atika KS 2002/40 is strictly designed for cutting wood. Using it on masonry, plastic, or metal is dangerous and will damage the tool.

Is this answer helpful?

A

Check the chain tension before every start, after the first few cuts, and regularly every 10 minutes during continuous use to prevent accidents.

Is this answer helpful?

A

No, the oil tank is not filled at delivery. You must fill it with biodegradable chain saw oil before the first use to prevent damage.

Is this answer helpful?

A

No, minors are strictly prohibited from operating this chainsaw. Only persons with sufficient experience and training should use it.

Is this answer helpful?

A

If the chain jams, switch off the machine immediately, remove the plug, and use a wedge to free the guide bar before restarting.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Powerful 2000 W motor for efficient cutting
  • Chain brake stops the saw in under 0.1 seconds
  • Claw stopper provides stability during cutting
  • Automatic chain lubrication system included
  • Suitable for private garden and hobby use
VS

Disadvantages

  • Not suitable for professional forestry work
  • Corded design limits mobility compared to battery models
  • Requires regular sharpening and maintenance
  • Cannot be used in wet conditions or rain
  • Must avoid cutting above shoulder height for safety
M: QW-35-FL

Product Specification

Type

Chainsaw

Power

2668.3W

Bar Length

15.75in

Chain Speed

44.29ft/s

Chain Pitch

0.375"

Chain Oil Tank

6.76fl oz

Features

Softgrip, Additional Handle, Brushless Motor, Tool-Free Chain Tensioning, Automatic Chain Lubrication, Chain Brake, Claw Stop

Vibration Level

16.04ft/s²

Noise Emission

109dB(A)

Weight

12.57lb

Package Contents

Saw Bar (Oregon), Saw Chain (Oregon), Bar Guard

M: QW-35-FL

Product Description

Atika KS 2002/40 Electric Chainsaw Review

The Atika KS 2002/40 is a robust electric chainsaw designed specifically for private use in home gardens and hobbyist projects. With a powerful 2000-watt motor, this tool delivers efficient cutting performance for tasks such as sawing logs, branches, wooden beams, and boards. The machine features a 400 mm guide bar, making it ideal for handling medium-sized wood pieces without the bulk of larger professional models.

Safety is a primary focus with the KS 2002/40. It includes a chain brake that stops the saw chain in less than 0.1 seconds upon activation via the front hand guard or release of the trigger. This feature significantly reduces the risk of injury from kickback, a common hazard when the tip of the guide bar hits an object. The device also comes with a claw stopper that acts as a lever to help stabilize the saw during cuts, further enhancing user control.

Operation is straightforward once assembled. Users must ensure the chain is correctly tensioned and lubricated before starting. The oil tank holds approximately 235 ml, allowing for extended periods of work before refilling. The automatic chain lubrication system ensures the chain remains cool and sharp throughout operation. For power, the saw connects to a standard 230 V outlet. When using extension cords, it is crucial to select one with sufficient cross-section to prevent voltage drops that could reduce motor performance.

Maintenance is simplified by accessible components. The cover can be easily removed to check the chain wheel and replace the saw chain if necessary. Regular cleaning of ventilation slots prevents overheating, while sharpening the chain keeps cuts clean and safe. The manufacturer recommends using only original spare parts to maintain safety standards and warranty validity.

Important Notes

  • Do not operate the saw above shoulder height or on unstable surfaces like ladders.
  • Always wear protective gear including eye protection, hearing protection, and cut-resistant gloves.
  • Never cut materials other than wood, such as plastic or masonry.
  • Ensure the area is free of people and animals before starting work.
M: QW-35-FL

© Copyright 2026 Manual.ly